This is a video on How to make a 2004 2005 2006 Jeep Liberty 3.7 Engine work in a 2002 or 2003 Jeep Liberty. Need additional info feel free to contact us at 616-430-3114. www.engine-guru.com
The reason we did the video was because the 2002 and 2003 engine are hard to come buy and cost more than a thousand dollars extra than a 2004 2005 or 2006 because they are hard to find.
I done the motor swap but didn’t realize my original motor was ngc and the donor is jtec but it runs completely normal wit the ngc tone wheel and the jtec reluctor but won’t rev past 2400 and act like the crank sensor is bad I also have the proper reluctor ordered through airram
just a little heads up to help a install go smoother. there is a collar in the flywheel side of the crank shaft you must remove to fit the earlier model years.
It will bolt up they are the same . I have seen where people do not take out the pilot bearing for the clutch and therefore think it does not work .We have done many of these with no problems.
Very informative, great video. Will this work for me? I swapped 2001 3.7 from Jeep liberty into 2004 Durango 3.7. However, vehicle will not start. Can I use this kit to correct issue?
I have a 2005 Jeep Liberty v6 37.1 I change the water pump I change the spark plug it still won't stay cranked unless I keep my foot on the gas I took it to the mechanic shop to ask him to put a crankshaft on there he said it wasn't no need because the engine was gone is that true
So would I need a crank position sensor and a cam position sensor for a 2006, 3.7 l engine? I've replaced my 2002 engine with a 2006 engine and it won't start. I've purchased and installed 2002 cam and crank sensors.
I suppose it would be the opposite if I wanted to put a 2004 into a 2008? Meaning put all the 2008 ring and gears into my 2004. Besides all the other plugs and intake etc.
Hello is that just for the old transmission if you wanna put a new engine in a old transmission or can I just take out my 2004 liberty jeeps engine and transmission and put it on the 2002 liberty. Or.would I have to take the computer and wiring harness out the 2004
Can you install a new 3.7 engine into a 2002 or 2003 Jeep Liberty that had a 2.4 engine. Can one convert it from a 2 wheel drive into a 4 wheel drive and keep the 5 speed manual transmission? Thank you
I have an 02 I bought new for the wife. Just turned over 30k miles on it because she doesn't use it a whole lot. My question is two fold. Is it a question of when this engine will blow not if? I mean is a new motor in my future if we keep this? If so and I decide on a remanufactured motor or your kit does this fix the problem that brought this about or do I yet again face it with the new one too? Thanks
Is the '04, '05, and '06 v6 more sturdy than earlier models? I don't understand how the discussed differences materialize, for example, maybe in areas such as engine performance/longevity.
i liked the video. i have heard that the engine will not bolt up to the trans. can some one let me know about this. i am on my third engine for my o2 thanks
Hello Kevin I needs some help if you can. I have a 2008 Jeep Grand Cherokee with a 3.7 engine which is bad. Well I found a 2005 Jeep Liberty with a 3.7 engine with low miles and I was wondering would the 2005 Jeep Liberty 3.7 engine work in my 2008 Jeep Grand Cherokee 3.7?
So if I have the old engine out of my 2002 and I purchase a engine for a 2004,2005,2006 coulndt I just remove the gear and ring from my old engine and pit it on the new engine? Will they not work?
hi, i have liberty jeep 2001 limited edition the engine does not fire and it three of the plugs soak oil. i have change the fuel pump, service the nozzles, check the coils, check the valves but the problem still remain. one repairer suggested changing the brain box while another buying of new engine. i don't know what to do please someone should help me
before I buy the kit,, can I swap my camshaft sprocket and the crankshaft ring from my 2002 to the 2005 newer engine ? also does this has to be done on dodge 3.7 rams ? thank you very much
I have a 2002 Liberty 3.7 and just got a 2004 3.7 engine... can you just change the tone wheel and Relucker ring crank shife from each other?....like just switch them from the each other....well it work that way too or do you have to get the kit?....
Good afternoon I have a jeep 2004 3.7-liter engine , automatic transmission , limited edition, more than 2 years ago I had problems with the engine and decided to change it, the mechanic who made me work I install a motor 2005 , and since making the change the car has had problems with ignition and does not advance to more than 2500 rpm , talk to a new mechanical and tells me that the problem might crankshaft trigger phaser ring not match my truck, opened the engine and showed me the part to buy that really has to go. You could tell me if they support the 2004 and 2005 , or tell me that the bug is in my car. I appreciate your help
Hello sir. Quick question. I have a Jeep Liberty 2005 with a working motor of 2002. But it doesnt crank over to start. Do I need to get a different kit for a new to older?
Ok what about the computer and harness's, the 2006 has a 4 connector computer and my 2003 has a 3 plug computer??? How do I get around that, motor is in, but those are different???
Hi, I'm actually about to install a 2006 liberty engine in my 2002. You mention that you can buy the reluctor ring and the timing kit from you directly. I'm trying to find a website or something for you so I can check into purchasing these from you. Can you please let me know how I can find you? Thanks!
Hi Kevin. I have an 04 that decided to grenade on me. So am I safe in stating that a 05/06 will be a straight swap? What about a 07 and newer model? Thanks.
kevin you seem to know whats up with jeeps...im in a bind and my engine blew in my 3.7 v6 out of my liberty (2004) would you know of a good place to get a used engine? i did the math and with me doing the work myself it cost just as much to buy a motor then it does to rebuild it properly everyplace ive found wants 1500 or more
a este instructivo le faltan muchas cosas como que mo solo tienes que cambiar el cranshaf es necesario cambiar volante bulbo de aceite maniful de admicion retirar un aro que sentra la turvina porque de lo contrario el motor no acopla con la transmision y por ultimo antes de desarmar el tiempo del motor crea tus propias marcas en sigueñal y ejes de leva por si el tiempo del motor no coinside con el manual lo digo por experiensia
is the '04, '05 and '06 v6 more reliable than the '03 engine? Basically, I'm asking why would someone want to do an engine swap being the horsepower and torque ratings are very similar.
I have had some conflicting information about being able to swap a 2003 engine into a 2002 Liberty. Some say yes some say no. are the reluctor ring and the tone wheel the same for the 2002 and 2003?
Will a 2012 3.7 still work in a 2002 with this kit? I know I may have to tap some bosses, but will the change in cam and valve spring size cause any issues?
Kevin. I have a 2002 3.7 Liberty 3.7 and the right cam wheel has jtec stamped on it. I also have a 3.7 from a 2003 Liberty and the right cam wheel is also stamped jtec. Does that mean that I can put the 2003 engine in the 2002 as is?
I have a 2004 Jeep Liberty and have access to a free engine from a 2002 Jeep Liberty. Would the process be the same in my situation? Just pull the tone wheel and reluctor off the old 04 engine?
I’m axing everybody around can you put a 2011 jeep liberty sport engine 3.7 into a 2011 Jeep liberty 3.7 or can you put it engine from a jeep liberty 2008 and put it into a 2011 Jeep libertyor you could put a 2009 or a 2010 or 2012 jeep liberty 2011
I'm in the process of putting an 06 engine in an 03, but im going a different route and swapping the wiring bundle, the ECU and fuse box, ect... I'm down to the security/ICM to get ign spark, but since none of the wire colors match up its kind of a headache. Disassembling the motor probably would've been easier now that i I'll look back at it.
Shawn Sohayda did you ever get it to work? I have an 02 liberty that had an engine fire and original harness burned up with a bunch of electronic damage. I have a used 04 engine with complete harness computer etc. I think in my case changing computer and everything is going to be easier. Did it work for you?
The 45rfe setups didn't use a pilot bushing in the crank, the 42rle setups, did. No dimensional changes were ever changed in the casings of the 3.7 cranks in terms of when they migrated to 42rle. If you compare the 02 parts fische to the 04 fische , 04 will list the bushing, etc.
04,05,06 used engines cost the same as 03 and 02 so why would anyone care? This guy is right though this is all covered on jeepkj forum. The only hard part about swapping yourself is the transmission disconnect because the converter and clutch disconnect procedures. They are covered in the Chilton book though. You can do Dakota and 1500 engines in to liberties too and automatic and manual engines are the same. Watch out for the oil pumps failing on these engines.. Even aftermarket. Engine killer.
egje EORWIJ there are some things that changed. the main thing is the newer engines fixed the valve seat issues with the 02 and 03s. the 04 and ups have better lash lifters. along with a different profile cam. they fixed some of the oiling issues also in the ones used in the 07 and up.
Hello. I have a problem.. I have a 2002 liberty and tried to put in a 2003 engine.. The toqure converter wont fit into the crank of the engine.. I was told that 2002 and 2003 engine only.. Why wont the converter fit into the engine and how do i fix this problem... I am ready to burn this liberty..its a 3.7 L . Any input would be helpfull Thank you
i have a 2004 dodge truck, and the motor is a 4.7 with ring conversion 32 and i put a motor 4.7 and it has a 12 ring conversion. but it wont turn on. what should i do?
I have an 02 liberty and put the 3.7 from an 06 in it. I took the reluctor ring and cam sprocket off my old motor and swapped it but now the torque converter won't fit into the flywheel