Great video! Here is the translation for the sprocket parts: HTD / RPP Zahnriemen 370-5M-9 mm breit Teilung 5 mm HTD / RPP timing belt 370-5M-9 mm wide, pitch 5 mm 60-5M-09 HTD Zahnscheibe - Typ 6/6W Zähne: 60 60-5M-09 HTD sprocket - type 6 / 6W, teeth: 60 20-5M-09 HTD Zahnscheibe - Typ 6F Zähne: 20 20-5M-09 HTD sprocket - type 6F, teeth: 20 SDP/SI should carry them in the U.S. As other comments have stated, it is for small parts otherwise the motor will not hold. It will be rotated by the cutting force.
For the 4th axis I use the nccad9 (kosy) only. A simpe interface for the 4th axis is build in nccad9. So far I used the 4th axis not so often and I‘m not shure to invest the time to find out how PP and Fusion360 work with the 4th axis.
Super gebaut. Ich bin zurzeit auch am planen um mir eine 4.te achse auf meine Kosy2 a3 massiv zu bauen. Ich finde allerdings die Pol belegung im Stecker nicht. Wissen Sie wie die Pole belegt sind damit ich meinen Stepper motor richtig anschliessen kann? Freundliche Grüsse aus der Schweiz Florian
Hallo Florian, sende mir Deine email adresse auf hilmar.theiss bei googlemail. Ich sende Dir dann gerne ein Bild mit der Belegung der U Karte vom meiner Steuerung
Hallo Hilmar, schönes und informatives Video (wie immer). Ich nutze ebenso die MCS von MAX mit NCCAD Vers. 9. Dabei stellte ich fest, dass ich U-Achse im Programm nicht "nullen" kann ("G54 U0"). Wie ist dazu deine Erfahrung? Leider hat mir MAX diesbezüglich keine Rückmeldung gegeben. Gruß Stefan.
Hallo Stefan, Bei mir funktioniert es, wenn Du möchtest dann maile mir Deine Telefonnummer, ich rufe zurück und helfe Dir. Da kann ich Dir schon einige Tips geben. (hilmar.theiss) auf googlemail punkt com.
Hallo Hilmar, vielen Dank für dir Rückmeldung. Die von dir aufgezeigte G-Code Folge funktioniert, war mir auch bekannt. Ich nutze den G54 Befehl um innerhalb eines Programms einen neuen Nullpunkt zu setzen. Bei der MAX Steuerung funktioniert das bei der XYZ-Achse aber nicht bei der U-Achse. Der folgende G-Code soll dies verdeutlichen: ;----------------------------------------------------------- ;Annahme - U-Achse steht auf 0 Grad ;----------------------------------------------------------- G00 U10 ;U-Achse wird von 0 auf absolut 10 Grad gefahren G54 U0 ;U-Achse wird "genullt" G00 U90 ;U-Achse wird auf absolut 90 Grad gefahren Bei mir ist es nach Abarbeitung der Befehle so, dass die U-Achse nicht auf absolut 90 Grad sondern auf absolut 100 Grad steht (10 + 90 Grad, G54 Nullung ohne Effekt). Das ist meines Erachtens so nicht richtig, da im Code mit "G54 U0" die 10 Grad auf 0 Grad gesetzt werden. Deckt sich das mit deiner Steuerung bzw. Erfahrung?
Hallo Stefan, das deckt sich mit meiner Erfahrung. Ich gehe davon aus das Du am Referenzpunkt auch als erstes den absoluten 0 Punkt gesetzt hast. In Deinem Beispiel setzt Du dann auf 10 Grad einen absoluten neuen 0 Punkt und dann gehst Du von diesem 90 Grad weiter. Dann bist Du 100 Grad vom Referenzpunkt entfernt. In einem Telefonat geht so was aber schneller zu klären. VG Hilmar
hi can u give some more info of that gifted part ? is it harmonic drive in box ? if yes what is part number ... i planing to build one too but ,,planetar, harmonic ,mix of 2 .just dont know which will be good but easy to make
This is a direct drive solution (no harmonic drive). This solution without a break is only useful for creating small parts.I look for a electronic break bud did not find a any so far.
You could try a traditional electric motor break, couple it to the secondary pulley, or axle depending on what you can get, normally closed and simply have it on has the motor receive movement signal, would try to enclose the pulley´s if I were you though, good luck