How To Make A Lower Cabinet Base - WOOD Magazine 

Nice. I like the corner clamp supports shown. I am going to make some. Solves one of my bigger challenges. Thanks.

Good video, easy to follow with some very good tips that will help with other projects.

Educational...thanks

Excellent! Thanks!!!

If the cabinet is in the middle of a run leave the good sides for the interior. It’ll make your cabinets seem more expensive

Very interesting Sir

Edge banding done after cab is assembled or prior to assembly?

This is a great video! When/how do you attach the back panel? I didn’t see it in the other videos but I may have missed it. Thanks!

I really like this mans presentation. He explains everything well. I wish I could get hold of him. I would like his take on faceless cabinets. Not sure if there is more to do than just complete cabinet as he has and trim the faces with iron on or wood strip? Or is there are other considerations due to the weakening due to no face frame.

How long you have keep it clamped before u instal face frame

Nice one! Looking forward to the next video!

What dado set do you use?

What are the clamps called that you used for your sacrificial fence

I wonder, are you using fine or course thread pocket screws?

Nice build! So the back stretcher is visible? Did the back panel go on behind the stretcher or did I miss something?

At 4:28 you say the dado is 4" up from the bottom. At 5:48 you say 4-1/8" up from the bottom. What changed?

Assembling the cabinets with pocket screws must be a new thing at one point they were only used for the face frame and the box was Assemble by nailing it with a 15 gauged nail gun but I like the pocket screw way better looks more professional

What type of would do you use?

What issue of the magazine would I find the plans for the tapered outfeed support stands he used?

a piece of masking tape works great for stopping tearout

Nice video, I just wish it would have better resolution

Labor extensive and a good table saw required

No material list on sizes?

Hate plywood, I made basically the same thing using 3/4” black walnut and it looked fantastic

I like the video and you show excellent skill and processes so please don't take this the wrong way: I am bemused by the American style of building kitchen cabinets. I do understand that you prefer the "traditional" style of framed faces and we actually have that sometimes here (Europe) in fact the last kitchen I installed (at my sister's house) is furnished with separate frames and doors on special hinges which wrap around the frame. They look very nice, (I hate them but I am a minimalist to the core) especially in a cottage style kitchen. My biggest query is why do you still make the cabinet box to the floor and cut in the "toe-kick" while we stopped doing that on all kitchens about 45 years ago? Even cheap cabinets are made all over Europe with a rectangular box roughly 700mm (28") high (base and wall) with four adjustable plastic feet fitted under each base cabinet as they are installed. Once the cabinets are adjusted for height to compensate for any uneven floors they are joined and fixed to the wall then a continuous 150mm (6") plinth board is clipped across the front of each cabinet run. Ideally this plinth has a soft plastic trim on the floor contact edge to prevent minor spillage of liquid under the cabinets. The major advantage of this style is that our commercial kitchens are made from high density chipboard because it is strong and rigid and faced with melamine it is always dead flat and even 15mm (1/2") board is suitable for cabinets; there is one drawback which is that if the chipboard becomes wet it blows out and becomes useless so we avoid contact with the floor in case a kitchen flood occurs! The dishwasher and washing machine or even the plumbing at the sink or a large pan or container can quickly soak a floor and ruin the woodwork. Probably the best style is the Spanish system in which the base cabinets are fixed to the wall with a space underneath so the tiled floors can be washed easily from wall to wall. I love to watch North American woodwork videos and I admire your excellent work but please: why wood to the floor?

Ah, are you Ahmish?

You lost me soon as you started. You never showed cutting the carcass to begin with. You went directly to cutting toe kicks. ??

enough with the pocket screws. dowels, biscuits, dovetails, half-lap, dado, domino, bridal, or a combination of a dado and dowels. there are so many good woodworking joinery techniques but pocket jigs are not part of this group. they were developed by high production cabinet manufacturers so sped up their line and save money, it’s a cheesy way to do things. there are new comers to this industry and they think this is normal. it’s not !