No video :(

How to Make a Police Utility Rack | How to Make a Tactical Rack / Beginner CNC Project

Подписаться 3,8 тыс.

Просмотров 7 тыс.

50% 1

In this video I share with you how to make a simple police utility rack. I also incorporate the help of my CNC but it not required for this project.
Hope you enjoy and are able to take something away from this video.
As always, thank you for your support!!
Facebook: aetimberandpine
Instagram: aetimberpine
Etsy Link to SVG File: www.etsy.com/a...
Setup in Carbide Create: • How to Make A Police U...
Total Dimension: 12"x31.75"
- Flag Dimensions: 12"x31"
- Top Piece: 3.5"x31"
- Side Pieces: 3.5"x (Width is cut to size during build)
Hardware: all hardware is 3/4" threading
2x flanges: amzn.to/3gq53HD
3x close nipples: amzn.to/3rseDQu
3x caps: amzn.to/3L4Id6u
2x 4.5" nipples: amzn.to/34A2xMu
1x 45 degree elbow: amzn.to/3Htvok3
1x T-Fitting: amzn.to/3LbLP6P
CHECK OUT THE MERCHANDISE: aetimberpine.c...
Materials/Equipment Used
Glue: amzn.to/3uu2Z9Q
Mask: amzn.to/3gnOhc3
Brad Nails: amzn.to/3rtAqri
screws: amzn.to/3GqDNTX
Glue Bottle: amzn.to/3AXQhBk
Router: Bauer Trim Router
1/4” Upcut Endmill: amzn.to/3GuBFug
90 Deg V-Bit: amzn.to/3rrqKxb
60 Deg V-Bit: amzn.to/34wswEq
XFasten Double Sided Tape: amzn.to/3Hu95Ld
Keyhole Bit: amzn.to/3GxpKfk
Table Saw: amzn.to/3B1e6bv
Miter Saw: amzn.to/3B0kZd1
sand paper: amzn.to/3rsuLl9
sanding block: amzn.to/3ruLLqM
Behr Mega Blue: Home Depot
Varathane Ebony: amzn.to/3LatzL2
Spray Poly: amzn.to/3J83lH4
Sweet Tooth by Blacksheep!: / blacksheepdenv. .
Music provided by Free Vibes: goo.gl/NkGhTg

Опубликовано:

29 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 17

@patrickdepass9031 Год назад

Thank you for taking the time to post and share. You do awesome work.

@aetimberpine Год назад

Thank you Patrick. I appreciate these comment.

@jamesinstone7377 2 года назад

Nice content.

@aetimberpine 2 года назад

thank you for checking it out and your feedback! I appreciate it!

@tony97gt Год назад

Solid work my friend

@aetimberpine Год назад

Thank you Tony 🙏

@sergiothehandyman Год назад

Awesome work, what size is the union. Thank you.

@aetimberpine Год назад

Thank you Sergio. It’s tough to say because I am using a cnc and I make the entire flag fit within the dimensions of the piece of wood not just the union. If I were to give you a starting point I would use 14.875 (14 7/8) (wide) x 10.5” (tall). This is the dimensions of the unions I make when making flags with a separate union. I also have a video where I go through the carbide create setup if you need to see how I did that. ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-Z5kqa8hQOtg.html

@sergiothehandyman Год назад

@@aetimberpine Thank you, i'm going to check the other video..

@AuntShellycom 8 месяцев назад

beautiful work ! how do you hang this to a wall?

@aetimberpine 8 месяцев назад

Thank you Auntie! I use keyholes in the back of the flag board. I cut those in before starting. I like how it lays flat against the wall.

@SbfWill Год назад

This is beautiful! But do you think those 3/4 screws will be able to hold a 20 pound vest? Also How much are you selling them for?

@aetimberpine Год назад

Thank you! I'm between 250.00 and 300.00 for this piece depending on any additional customizations. The hardware can add up quick though too. I recommend getting it off of Amazon because HD can be expensive which is where I've been getting it from.