How to make a Scroll Saw Bowl - woodworking 

Saw your video through Steve Good's Scroll Saw workshop. This is the best video ever to show how to make a bowl like this. Thanks so much.

Thanks for the feedback. I actually put in an order for a Shop Fox 16" last night, so we will see how it does. I am really looking forward to a scroll saw. I bout it along with a Grizzly bandsaw that I have wanted and saved for for a long time, so my woodworking is about to take some interesting new directions.

Really nice ! And, all that sanding paid off. Thank you for sharing your technique. Eric

Thankyou ever so much, I learned something new today. I often wondered about the angle compared to the wood thickness. Thankyou for sharing your expertise.

Really nice bowl and love the clamp,might have to give this a go.....

I would like to thank and congratulate you for you share with all of us all those projects, enabling all of us who are starting in carpentry as hobi and be able to do so many wonderful things. Big hug.

Looks great!

muy bonito, me encanta

I don't own a scroll saw and likely never will, however, I watched this entire video... Twice. Very cool. :)

Nice clamping system :)))) good job!

Awesome job

May I congratulate you on using gravity for clamping, and a tree stub on which gravity may act. You have there a nice bit of geometry how one can get a voluminous effect from a small thickness plank. There is good logic how to obtain that angle for the cut.Problems like this should be given to school children to find solutions to problems. Once I had a mathematics teachers who could not see how his mathematics are applied in three dimensions and to him mathematics were simply remembering formulas. Once I made model out of straight lines to make hyperbolas and cones and parabolas and when I told him that is what he teaches me, he was surprised that I could depict what he told me in three dimensions as in this case. Congratulations, this bowl has much more richness in knowledge that one can show on a video. Hope that many children see this.

Nice first time bowl.

it beautiful :). awesome

contrasting wood would definitely be an improvement! The scroll saw is a Rexon VS4003A. It vibrates heavily, so I would not buy it again.

OBRA DE ARTE

hermoso trabajo, felicitaciones jorge de argentina

If you look under the table of your pillar drill there is a nut that you can loosen and then you can tilt your pillar drill table to any angle you desire. Just do the nut up again when you reach the desired angle you want to work at.

Maravilha de trabalho, parabéns!

You're so clever!

thank you :)

great work. have subscribe!

I added the link in the description

Отлично! Лайк!

genious

My wife really liked it, so did I. Especially for your first! I think it might look nice to add one (maybe more?) rings of a contrasting color. Can I ask what kind of scroll saw you have, and do you like it?

A very good video but could you please advise the lines you made regarding finding the tilt of the table? How did you develop the spacing and what did it turn out to be. Also what is the wood and more importantly what is its thickness. I look forward to your reply if you would be so kind. Thanks again.

Well done! Is slightly curved wall section achievable by varying pad angle?

thank you

A little trick with polydraw. If you make the # of waves negative you get petals. If you make the # of waves negative and the wave amplitude negative, you get a burr. Dave

Oi boa noite gostei muito da sua criatividade pós sou iniciante em arte seria pocivel me manda uns gabaritos das suas artes. (Caneca,jarro,etc.)

Hahaha. "Sanding sanding sanding sanding sanding ...... sanding" i know that feeling Looks very nice

respect! 8-)

You're welcome

Very nice, what kind of wood did you use?

nice job! Do you need to drill pilot holes on each rings? Thank you And what kind size is the pilot holes?

Oi boa noite gostei muito sua criatividade pós sou Artesã iniciante

Did you use a skip tooth? Curious as to what blade. Love how it turned out.

Fabian It is always nice to see people successfully designing bowls with Polydraw. (available at scrollmania.com) Great job/

Where can I buy that long flap sander for the drillpress?

Otherwise the rings would not lock into each other. They would simply slip through, because of the material cut away by the blade.

Thanks, I used pear wood.

mit welchem programm wurde die schablone gemacht ?

what is name of your scroll saw? I using proxxon 460 and I think that its impossible to make same with proxxon. What type of wood you using??

du findest die Software hier: scrollmania (dot) com

points for using mask during sanding, not all use :)

The wood is 1.7 cm thick pearwood. Regarding the lines, I'm not sure I understand your question. The lines have the exact same spacing as the rings. Just take a scrap piece of the same piece of wood, and extend the lines downwards using a combination square. Did you look at the template in the description?

Good night, Fabian's. I wonder what angle you used to make the cuts for this BOWL? Thanks and a big hug.

Sir, why do you cut at an angle?

with taht much Sanding, you could start your very own private Dessert.. :p

where can i download the template??

do you have a website where i can find all patterns?

Excellent job. Unfortunately, I hate sanding but I can see it is a necessary evil. I want to make a set of "nut" bowls for a few friends but now, I'm wondering how good of friends they are. LOL.

Wirklich schöne Videos! Lässt mich meine Dekupiersäge mit ganz anderen Augen sehen... :) Darf man fragen, was das bei 4:10 für ein Aufsatz an der Standbohrmaschine ist? ist das ein Eigenbau? Beste Grüße,

Ist diese Schale wasserfest oder kann man da nur feste Stoffe rein tun?

Where did you get the pattern>=?

Is that a Pegasus scroll saw ?

DONDE PUEDO ENCONTRAR EL DIBUJO PARA HACERLO UN SALUDO DESDE ESPAÑA

Muy bueno, pero Dios, lija y lija y lija... (sanding, sanding, sanding...)

मैं