How To Make Fast Charging Station 

Cheap alternative But the thrill of making a working project is missing

Shut up

ㅋㅋ'ㅋㅋㅋ

I was thinking the same thing lol

Hi I could not understand your question? Did you mean that 0.5A for each usb is not sufficient? I do not have the answer to your question as I am a beginner and I am trying to understand your question.

Well...after this video you know less. If you have more than 2 ports connected your phone wont be charged in 4x the amount it did before. 2 ports...about normal. 1 port...then it's a fast charger

Because it needs a charging protocol charger + and - and TX and RX pins need to be connected to an charging ic if else your phone won't charge if charging it's not charging it's damaging the charge protection and charge ic in your phone which leads to replacement of an ic mostly they won't replace ic instead motherboard needed to be replaced

You are absolut Right! But, how can i make this only with 5V y 4Amperes? Do you know?

@@suiyen ebay buck boost converter , cost 10 bucks. 6-40v in --1.2-35 v out at 20 amps. 300w CC CV

ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-XpxoFkLgy0M.html

ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-XpxoFkLgy0M.html

Ok

ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-XpxoFkLgy0M.html

@@easytechzones he commented something great an you just replied OK??? THAT IS RUDE!

@@easytechzones bhai Jan ye Sara saman khn se milega

@@easytechzones plz guide me

There's no way it can work properly as shown, let alone as a fast charger. At a minimum the data pins need shorting together and last time I checked glue is not a conductor 🙂 Then those buck converters are not the right tool for the job (even in the video you can see the voltages are all over the place and risk frying your device). There's also some pretty major safety fails, for example not even heat shrink covering the mains solder connections meaning one loose wire inside could kill you or your devices (the boards that get hot are held together with hot melt glue FFS which is just stupid and likely to kill someone if it's knocked and comes loose)! Seriously folks, don't try and build something like this, like that. At best it won't work properly, at worst you'll kill someone.

Shut up

Thankyou

@@easytechzones wkskjsj

👍djddj to get a good morning ma'am please see the attached screenshot for the prayers

Thankyou 🙏

ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-XpxoFkLgy0M.html

Yes you have pointed out this flaw correctly.

Would the charger be rapid? After replacing resisters. Are there already resisters after TI431?

He's wrong use the buck converters there capable of 4 amps I believe

@@emilyhouse9642 how can buck converter give more Amper more than 12v charger although 12v charger is powering buck converter

You are right bro I am thinking that thing Nice work bro without data pin any phone couldn't take aftre from 10 watt And also his voltage and current is not stable And also buck converter is lass less efficient than any fast changer

He has 6 out put every out give around 7 to 8 watt because of loss in buck converter And also his computer power brick / main power supply give 12v at 5 amp = 60 watt at maximum so every usb get 10 watt So this is a power supply which have 6 usb ports and give around 9 ~ 8 watt in every socket Sorry for the creator but you make a power supply to a useless thing

I agree with you.The buck converter has no charging function, so it's not fast charger. It's only the 5V adapter.

it's an advice for everyone, I'm actually using a 3A buck converter from 9V old classic style transformer to staple 5V DC and but i use a car double usb female heads only because its has resistors between data pins it's fast and efficient but not 40W

Thank you for honest comment I like it much I am a beginner and learning from you . ang I also learned from other comments

Don't try it, you will stuff up your phone's charging IC

Not possible

@@easytechzones Can you explain why is not possible to use all the USB at a time?

In this video i didn't use any arduino

In previous video use 5 v

In Any ardinuo only we will generate 5v or any high volt

Bro my mobile was supported 20w fast charging so can I generate 20watts or only 5v

5v 5mA dc

وحيش

Amazon pe cutting mate search kijiye

@@easytechzones sir bhuttt time lga kl dundhne me tb jaa k mila thank you sir

Thankyou 🙏

@@easytechzones Welcome sir

How u can say that it's fast 🔋⚡

Super bro

It's hardly fast if you consider how many ports there are. Why do people do this lying thing all the time?

RIP Powerbank module I charge With Ic7805 (5v regulated)

No dont make it you are wasting your money

Thankyou 🙏

Thankyou

Thankyou 🙏

Welcome 😊

Q

U

@@easytechzones *Brother ye table kaha se purchase kiye ho* *please btao please* 🙏🏻😟

Thanks

Use 12v 10amp smps

ok

this is fast charging project!!! ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-rpP9qRbDZtY.html

ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-XpxoFkLgy0M.html

Thanks 😊

Thanks

You will get 2.5 amp from each port(1st 4 porr)

This one is garbage for more than 2 ports and will only fast charge on one

Nice one

Yes. Easily available

@@easytechzones yes

Of course

@@easytechzones 😂yeah

Thankyou 🙏

@@easytechzones yiu make for me

It wont work. There are laws of physics that are broken here. If you think this guy has discovered a way to break ohms law, be my guest. Just so you know...he didn't. The more units you connect the less power each unit receives. It quickly becomes an ultra slow charger as you connect devices. Don't fall for this. Research everything you see online

Thankyou 🙏

@@easytechzones welcome bro