Тёмный

How to make raised panel cabinet doors in MDF  

Peter Millard
Подписаться 264 тыс.
Просмотров 202 тыс.
50% 1

This is a beginners guide to making loose tenon raised panel cabinet doors in MDF.
There are many ways to make raised panel cabinet doors, and having tried most, if not all of them, I can honestly say that loose tenons and lots of glue is the simplest way to achieve repeatable results, quickly and cheaply.
This video will guide you through the process - enjoy!
Please use the ‘Like’ button if you liked this video.
Please subscribe if you think you’d like to see more.
If you haven't already seen it then my video for Shaker-style panel doors is probably worth watching first:- • Shaker-style Panel Doo...
As an Amazon Associate, I earn from qualifying purchases made through these links:-
As an eBay Partner Network member, I earn from qualifying purchases made through these links.
Woodworking stuff:-
Blum hinges - amzn.to/2oOiiYG (US: amzn.to/2oOodgt)
Hinge drilling guide - amzn.to/2oYBHqk
Self-centering drill bit - amzn.to/2pVQ6kl (US: amzn.to/2oZ7Fmq)
Lost-tite screws - amzn.to/2pGnUFD (US: amzn.to/2pVKqa6)
Hultafors Talmeter tape measure - amzn.to/2pHwnbH (US: amzn.to/2oqLQc9)
Heavy duty groover - goo.gl/Ht1TU4
Arbor for above - goo.gl/xdE9PU
Panel raising bit - goo.gl/GceCdJ
Japanese folding pocket saw - goo.gl/DlcyPw
Spax MDF screws - amzn.to/2pj5FX5 (US: amzn.to/2oOh7Zu)
Spax screws - amzn.to/2oYWydc (US: amzn.to/2oOjkDT)
Tongue-tite screws - amzn.to/2ouKU5I (US: amzn.to/2pGBVk3)
Bahco 6” combi square - amzn.to/2oumhX4 (US: amzn.to/2ouSg9k)
Festool Domino - amzn.to/2pVSnMk (US: amzn.to/2o7E22Q)
Festool Domino assortment - amzn.to/2piZjHa (US: amzn.to/2pGv1Lx)
Festool Domino 5 x 30mm - amzn.to/2oTq5CZ (US: amzn.to/2oOqyrL)
Festool TS55 Tracksaw - amzn.to/2pGvzDS (US: amzn.to/2oOgGhw)
Festool Kapex 120 - amzn.to/2oYOXeq (US: amzn.to/2o7D3zL)
Workwear (seriously, somebody asked!)
TuffStuff Extreme 700 trousers - amzn.to/2oqeBpq
Scruffs Drezna trousers - amzn.to/2o7n44H (US: amzn.to/2oTAVbX)
Karrimor Supa 4 (not safety wear) - amzn.to/2oYYfHA
Dewalt Apprentice safety boot - amzn.to/2oYN8OP (US:amzn.to/2pVWLLr)
Photo/video gear
Seriously, gear doesn’t matter
• Casey Neistat's Guide ...
But if you like me, you quite like gear and you’re curious about what I use, then here’s the list:-.
Main camera Panasonic Lumix G80 - amzn.to/2o7uPrx (US - G85: amzn.to/2ouTwJV)
Second camera Panasonic FZ200 - amzn.to/2pj8p6Z (US: amzn.to/2oYSGJ0)
‘Walk-around’ camera Panasonix TZ55 - amzn.to/2pGqtVq (US: amzn.to/2o7vNnG)
Rode Videomic Pro - amzn.to/2oTAr5W (US: amzn.to/2oOp54A)
Rode SmartLav+ - amzn.to/2piXXw2 (US: amzn.to/2pGqRTU)
Backup mic K&F concept - amzn.to/2oYFt2W
Audio recorder Tascam DR 05 - amzn.to/2oTzJFT (US:amzn.to/2oZ2N0K)
Gorillapod - amzn.to/2ouOZqC (US: amzn.to/2o7I5fN)
Ball-head - amzn.to/2o7mpjH (US:amzn.to/2o7JUcJ)
QR plates - amzn.to/2pG4AWd (US: amzn.to/2oqgN0c)
Smartphone mount - amzn.to/2pGLAtt (US: amzn.to/2oOlL9D)
Magic arm - amzn.to/2oOoTlV (US: amzn.to/2pGmrwa)

Опубликовано:

 

3 окт 2024

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 267   
@bmc5180
@bmc5180 7 лет назад
Your videos are a gift and a curse. I find myself watching and rewinding these videos instead of actually working during the day. Thanks for sharing!
@10MinuteWorkshop
@10MinuteWorkshop 7 лет назад
Thanks - I think! If it's any consolation, I find myself wanting to make videos instead of working, too, LOL! Appreciate the feedback, all best & thanks for watching! P
@brianmosse
@brianmosse 3 года назад
This is a great method, never dawned on me before (and me a 50 year veteran of sawdust production) to do doors like this , good job mate.
@10MinuteWorkshop
@10MinuteWorkshop 3 года назад
Thank you! 👍
@rickgordon8377
@rickgordon8377 3 года назад
Feel compelled to thank you for helping me catch-up on skills and knowledge I don't have that much time left to learn on my own. You are an artist and clever genius when it comes to space and production. Appreciate you
@10MinuteWorkshop
@10MinuteWorkshop 3 года назад
Thanks Rick! And I appreciate you taking the time to make the comment. 🙌👍👍
@benitoruiz1615
@benitoruiz1615 2 года назад
Magnifico....me gusta mucho hacer puertas con MDF 3/4" .....siempre las hago haciendo un grabado con routers....pero esto esta mucho mejor....gracias......Saludos desde San Luis Río Col. Sonora. Mexico....
@heystarfish100
@heystarfish100 4 года назад
Hello Peter, I’ve been binge watching your channel and still have hours and hours more content to view. You sir are a Master of MDF woodworking. I look forward to learning more of your brilliant techniques. Thank you so much for your efforts in making this information readily available. 🇺🇸🙋🏻‍♂️
@10MinuteWorkshop
@10MinuteWorkshop 4 года назад
Thank you! Very much appreciated. 👍👍
@DesandSam
@DesandSam 7 лет назад
I didn't think I needed a track saw until I saw the set up you used in this video. It inspires all sorts of ideas for practical use! Thank you. Excellent door making process too, btw.
@10MinuteWorkshop
@10MinuteWorkshop 7 лет назад
+DesandSam Thanks!
@chrisE815
@chrisE815 3 года назад
What I'm realizing is once I build a track saw cutting station, I don't need a table saw. Look how accurate the cuts are when he cuts the excess tenon off.
@michaelstiller2282
@michaelstiller2282 6 лет назад
Holy mother of feather boards on a router table! Love it!
@10MinuteWorkshop
@10MinuteWorkshop 6 лет назад
Thanks! 😂😂👍👍
@berndheiden7630
@berndheiden7630 4 года назад
I‘m new to your channel (sub and bell!) and I‘m very pleased with your 10 min format! When I retire at night I like to watch a video or two on YT and I don‘t want to engage in a 45 min video format at that time. And they do say that you can talk about anything but not over 10 min. Keep up the clear and concise work and thank you for sharing!
@10MinuteWorkshop
@10MinuteWorkshop 4 года назад
Thanks, and welcome! Some of the videos do get a little longer - I have more to say sometimes - but I try and stay as close to 10 minutes as I can. 👍👍
@rick91443
@rick91443 7 лет назад
Yes, your track saw is very convincing(and I have TWO table saws.) Can never get over your logical, highly efficient way of doing things and explaining while you go...rr
@10MinuteWorkshop
@10MinuteWorkshop 7 лет назад
+Richard Rider Thanks! 👍
@Mrfreezeee1
@Mrfreezeee1 7 лет назад
Seen a lot of ways to make cabinet doors ,this is one of the easiest ive seen in a while ,can to do one on corner cabinet doors ,one piece and/ or two piece
@10MinuteWorkshop
@10MinuteWorkshop 7 лет назад
Thanks! Never done one this way, but don't see why corner cabinet doors should be a problem.
@karlpopewoodcraft
@karlpopewoodcraft 4 года назад
These videos really do help inspiring professionals Peter thank you. Such clear concise instructions as always.
@10MinuteWorkshop
@10MinuteWorkshop 4 года назад
Thanks Karl! Really pleased that these older vids can still be of use! 👍
@karlpopewoodcraft
@karlpopewoodcraft 4 года назад
@@10MinuteWorkshop oh I didn't realise it was an older video 😅 it just pop up on my feed so I assumed it was a new one. Obviously I've not seen this one yet so that's good 😁 I think I'll purchase a triton 1/2 inch router to mount under my table once I've secured my Domino, I'm just trying to find a good second hand domino at the moment but there hard to find around these parts. I have seen a few down south but nothing around me at the moment. 🙄
@10MinuteWorkshop
@10MinuteWorkshop 4 года назад
@@karlpopewoodcraft Ha! Yes, #11 - barely had a grey hair ion my head back then... 😂I think I've just posted #412! 😬 The Triton's a great router for under the bench; newer ones have above-bench height adjustment (mine doesn't) which would be handy. I think used Domino's are like hen's teeth - certainly at a decent price - as they hold their value incredibly well. Best of luck with the search - and let me know if/when you get hold of one, I'd be interested to hear what real-world prices are like, if you're happy to share. Cheers, Peter 👍
@karlpopewoodcraft
@karlpopewoodcraft 4 года назад
@@10MinuteWorkshop just made a offer on one in Huddersfield waiting on a response 🙄
@10MinuteWorkshop
@10MinuteWorkshop 4 года назад
@@karlpopewoodcraft Fingers crossed! 🤞👍
@michaelburton4521
@michaelburton4521 2 года назад
Nice one Peter I've got one of those raised panel bits and the same router as you ( b4 you got the new fancy one) Always scared me a bit but ive neen messing around with it tonight and with mdf it is straightforward. If anyone asks me to make raised panel doors I'll say yes.
@10MinuteWorkshop
@10MinuteWorkshop 2 года назад
Hey Michael, yeah, it’s the biggest bit I own, I think! Works fine in MDF though. 👍👍
@samartin745
@samartin745 7 лет назад
Thanks for the video Peter. Excellent timing as I'm about to do a kitchen refit with raised panels in Mrmdf. Keep producing the great videos. Like the style and format too.
@10MinuteWorkshop
@10MinuteWorkshop 7 лет назад
SA Martin Excellent, hope it helps! All best with the kitchen, and thanks for watching! P
@mickey533
@mickey533 Год назад
Bravo!
@marka9292
@marka9292 6 лет назад
That's a nice way to make doors.
@10MinuteWorkshop
@10MinuteWorkshop 6 лет назад
Thanks - works well! 👍
@Newspacehospitality
@Newspacehospitality 7 лет назад
very professional and skillful craftmanship, good!
@10MinuteWorkshop
@10MinuteWorkshop 7 лет назад
Jerry Hotel Furniture Ltd Thanks!
@michaelodonovan1908
@michaelodonovan1908 7 лет назад
Have a massive envy every time I watch you flip it down and cut with it : )
@10MinuteWorkshop
@10MinuteWorkshop 7 лет назад
👍 Best part about it is that you get your bench back every time you flip it out of the way! More detail about this in my recent workshop tour video btw 👍
@GosforthHandyman
@GosforthHandyman 7 лет назад
Great vid of a job being done properly. Greetings from Andy Mac up in Newcastle! :-)
@10MinuteWorkshop
@10MinuteWorkshop 7 лет назад
+Gosforth Handyman Why aye man! 😆
@GosforthHandyman
@GosforthHandyman 7 лет назад
Don't do the accent! 😆
@10MinuteWorkshop
@10MinuteWorkshop 7 лет назад
Gosforth Handyman Never 😂
@pcb1962
@pcb1962 7 лет назад
Thanks Peter, that's very useful
@10MinuteWorkshop
@10MinuteWorkshop 7 лет назад
Pleasure, glad you liked it! P
@joelfredricksen7895
@joelfredricksen7895 7 лет назад
nicely done
@10MinuteWorkshop
@10MinuteWorkshop 7 лет назад
Thank you!
@bombaydan
@bombaydan 6 лет назад
Great video thanks
@10MinuteWorkshop
@10MinuteWorkshop 6 лет назад
Thanks👍👍
@dustyhush
@dustyhush 7 лет назад
great now i can try one ! thanks Peter
@Dinny.
@Dinny. 5 лет назад
Hi Peter, you made this look very easy...I've got the gear but unfortunately not the space..still saving for a larger workshop...current "shed" 12ft x 6ft..can't swing a cat. Desperately in need of new kitchen unit doors and drawer fronts...your videos are inspirational..thank you 😊
@martinmackett2758
@martinmackett2758 5 лет назад
Hi Dinny. Don't give up I have an 8 x 6 shed and it's full of junk, so I built my whole kitchen including the doors on my deck, which is only 5 x 10 . Finding somewhere to put all the cabinets after making them was the worse part.
@silverfox8801
@silverfox8801 7 лет назад
Your loose tennon idea changed my life!? 😂 where did you learn that technique?? Been using cope and stick cutters for ages!! 👍
@10MinuteWorkshop
@10MinuteWorkshop 7 лет назад
+Big Guns Glad to hear it! Loose/floating tennis have been around forever, happy to pass the knowledge along... 👍
@talokanitv8432
@talokanitv8432 4 года назад
thank you sir for sharing
@nathanbuckley8977
@nathanbuckley8977 7 лет назад
this is brilliant
@10MinuteWorkshop
@10MinuteWorkshop 7 лет назад
Nathan Buckley Thanks! 👍
@Hasy84
@Hasy84 7 лет назад
Very neat and informative ..
@10MinuteWorkshop
@10MinuteWorkshop 7 лет назад
Hasy84 Thank you!
@chleq
@chleq 7 лет назад
great video Peter
@10MinuteWorkshop
@10MinuteWorkshop 7 лет назад
Thank you! Appreciate the feedback; new video up every Friday at noon, GMT.
@shifty277
@shifty277 4 года назад
Puts a smile on my face to see such craftmanship in this video, it might not seem much to you as i'm assuming carpentry is your day job and bread and butter. But especially in London whilst on large scale and small scale sites its so often I come across wood butchers who don't so the trade justice. The headless nailing at the end with the mitre saw for the panel pieces with the special saw, I've never even seen or heard of such a saw which is to be expected as i'm in the brickwork trade. Just out of curiosity whereabouts in the country do you carry out your work! Thumbs up.
@10MinuteWorkshop
@10MinuteWorkshop 4 года назад
Thanks! Yes, was a full-time cabinetmaker, now about 90% retired and concentrating on RU-vid/content creation. I’m based in West London, W12; Hammersmith, Chiswick, around there. 👍👍
@johnreinhart860
@johnreinhart860 7 лет назад
amazing job
@10MinuteWorkshop
@10MinuteWorkshop 7 лет назад
John Reinhart Thanks!
@smnhpkns
@smnhpkns 7 лет назад
excellent Peter, thanks for sharing
@10MinuteWorkshop
@10MinuteWorkshop 7 лет назад
Simon Hopkins Pleasure, thanks! P
@therighttoopenlydiscusside993
@therighttoopenlydiscusside993 7 лет назад
really nice job.
@carllamb6711
@carllamb6711 3 года назад
Peter mate Your bloody good mate Your going to cost me a lot of money I can see lol 👍👍👍👍
@10MinuteWorkshop
@10MinuteWorkshop 3 года назад
Haha, every video should come with a wallet warning! And thanks! 👍👍
@cassiya100
@cassiya100 7 лет назад
Nice easy way to make up shaker doors if you have a workshop with a router table but for me I build all my wardrobes and cabinets in situ working in peoples bedrooms and front rooms. I'd be lucky if they had a garden to do all my cuts. So I make them the other way in your video using 12 + 6mm MDF 9mm if I use mouldings. I always use concealed Euro hinges with 10mm screws so It 'doesn't push the 6mm apart how you pointed out in your other video. Just subcribed.. loving your work Peter..
@10MinuteWorkshop
@10MinuteWorkshop 7 лет назад
+cassiya100 Thanks, and welcome 👍
@philippendlebury4518
@philippendlebury4518 3 года назад
Hi Peter. Noticed you used thinner 18mm stock for the panel. We have 22mm MR MDF in stock - and prefer to use this if recommended. Thanks Phil First Wood.
@oseiasfaztudo9407
@oseiasfaztudo9407 4 года назад
you helped me a lot, here in Brazil this yma fever essd kitchen style, but as we were standing by the old standards, these techniques are not taught here, on youtube i am looking for days and i found you explaining it very well, if you have any tips on how painting the door teaches me.🙏🏻🤝🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷🇧🇷
@10MinuteWorkshop
@10MinuteWorkshop 4 года назад
Thank you! Video #029, ‘Painting & Finishing’ - ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-dgTN2QPgoD8.html 👍👍
@oseiasfaztudo9407
@oseiasfaztudo9407 4 года назад
@@10MinuteWorkshop and difficult to understand, if it had a Spanish translation it would help ja 😊
@MonkeyMagic78
@MonkeyMagic78 7 лет назад
thanks great work.
@10MinuteWorkshop
@10MinuteWorkshop 7 лет назад
Thanks!
@8leg.studio
@8leg.studio Год назад
Thanks this is great. Can I ask why you add the floating tenons in such a way rather than hidden and parallel with the rail? Is it simply speed/ efficiency when weighing up the routing techniques involved?
@10MinuteWorkshop
@10MinuteWorkshop Год назад
Thanks. Yes, simply the most efficient process. 👍👍
@iwantcheesypuffs
@iwantcheesypuffs Год назад
Could you also make the inside panel 1/4 in smaller on all sides and do a 1/4 round over on the inside of the rails and styles for a very similar effect?
@10MinuteWorkshop
@10MinuteWorkshop Год назад
Yes, that would have a similar effect, but not the same as a raised panel. 👍
@Filmchippy
@Filmchippy 7 лет назад
Nice one Peter hope you're well, might invest in a raised panel cutter. Nice when you need something a bit better than standard shaker doors...Chris
@10MinuteWorkshop
@10MinuteWorkshop 7 лет назад
Hey Chris. Yes, well thanks. Very impressed with the Wealdon cutter (link in the description) certainly handles MR MDF with ease :). Cheers, P
@dagored100
@dagored100 7 лет назад
Awesome. Thank you
@10MinuteWorkshop
@10MinuteWorkshop 7 лет назад
An absolute pleasure, thank you for watching! Glad you found it useful, and much appreciate the feedback. P
@bradleymasson1777
@bradleymasson1777 3 года назад
Love your channel; you're a natural. However, I would not glue the panel in place, it will cause the panel to warp. On a small door it should not be too much of a problem, but on larger doors it "definitely" will.
@10MinuteWorkshop
@10MinuteWorkshop 3 года назад
Thanks. I've made - literally - thousands of doors this way, and they've all been fine because everything is made from MRMDF which is just about the most stable board you can get. If you live somewhere where there are extremes of humidity or temperature then sure, but here in the UK where I live and work it really isn't an issue. 👍
@kamarudinbinhanipah7918
@kamarudinbinhanipah7918 5 лет назад
Not too many equipment needed yet a very good end product
@TrimasJaya
@TrimasJaya 2 года назад
Hi..can you inform us what kind of router bit we have use if our MDF thickness is 18 mm for making raised panel door?
@jimmymack9440
@jimmymack9440 4 года назад
A note to newbies: Do observe the manufacturers max recommended cutter speed (often written on the shaft) especially on larger diameter cutters where the peripheral speed is higher and the max speed (or N max) should be lower to reduce the forces on the cutter shaft and router spindle. *Avoid cheap, poorly balanced cutters*
@garrysmythe
@garrysmythe 5 лет назад
very good build, and a great video as always Peter, from Garry in Barnsley
@10MinuteWorkshop
@10MinuteWorkshop 5 лет назад
Thanks Garry! 👍👍
@fortifiedgentleman8827
@fortifiedgentleman8827 2 года назад
It’s heavy doors after while the Hinges not gonna hold them , but made well
@10MinuteWorkshop
@10MinuteWorkshop 2 года назад
This vid is getting on for 5 years old, and the doors & hinges are holding up just fine. 👍
@leegugino1467
@leegugino1467 Год назад
5:24 if humidity shifting is a concern how should you glue this door together?
@10MinuteWorkshop
@10MinuteWorkshop Год назад
With a fast grab water-resistant pva. 👍
@awstewar
@awstewar 6 лет назад
Do you have to sand the edges down at all? It would seem that the corners would be very sharp.
@10MinuteWorkshop
@10MinuteWorkshop 6 лет назад
They’re given a ‘once-over’ with a sander just to clean them up before painting; how far that goes depends on the finish. For spraying I’m starting to use an arris roundover bit in a router on the edges, but for hand painting it’s usually enough to knock the edges back with a sanding pad 👍👍
@michaelkilner5031
@michaelkilner5031 5 лет назад
Enjoyed that. Instead of using the slot cutter would it be possible to turn the piece 90 degrees on to its side and use a straight cutter. Best regards Mick.
@10MinuteWorkshop
@10MinuteWorkshop 5 лет назад
Thanks! Yes, but you need to take it much mor slowly with a thin straight cutter. A grooving bit is faster. 👍
@daviddoody3836
@daviddoody3836 6 лет назад
Hi Peter, great information as usual, just wondering why you don't you stile and top and bottom cutters to make joint and grooves that come with panel cutter in sets
@10MinuteWorkshop
@10MinuteWorkshop 6 лет назад
Thanks! The client wanted the profile of the panel to match some skirting board I made for the room, and you don't get this profile in a raised panel set AFAIK.
@peckelhaze6934
@peckelhaze6934 6 лет назад
Is it possible to veneer mdf? Very useful video.
@10MinuteWorkshop
@10MinuteWorkshop 6 лет назад
Yes, absolutely. Or buy it pre-veneered. And thanks! 👍👍
@peckelhaze6934
@peckelhaze6934 6 лет назад
I didn't realise they sold it veneered. Thanks for that.
@BethKjos
@BethKjos 7 лет назад
@5:50 the biggest reason not to worry about gluing it all around is that you are using MDF. unlike solid wood, MDF has isotropic expansion.
@10MinuteWorkshop
@10MinuteWorkshop 7 лет назад
+Ian Kjos 👍
@mururoa7024
@mururoa7024 7 лет назад
Isn't MR MDF less/not prone to that?
@Moe7133
@Moe7133 7 лет назад
I hate working with MDF! I hate all the dust it makes. Just make sure you are cutting in a good air filter area and wear a breathing mask.
@10MinuteWorkshop
@10MinuteWorkshop 7 лет назад
All wood dust is hazardous - I'm asthmatic, so particularly sensitive to it. Check out a few of my other videos, you'll rarely see me using a tool that doesn't have a hose attached. Take a look at my shop tour, you'll see the air scrubbers that run all the time I'm not shooting video. 👍
@BethKjos
@BethKjos 7 лет назад
A scrubber is near the top of my list of projects. Probably right after upgrading my centrifugal separator.
@ThePhiloctopus
@ThePhiloctopus 7 лет назад
I love watching your videos! Just wondering; you use loose tenons to fill the gap between the rails and stiles. Is there any reason you don't route a tongue into the ends of the rails and slot them straight into the stiles? Is is simply a trade off between an extra bit change and cutting some loose tennons, or is there another reason? Cheers!
@10MinuteWorkshop
@10MinuteWorkshop 7 лет назад
Thanks! Using a loose tenon made of the same material & thickness as the panel just makes for a faster build - one cutter, one set-up, one panel & tenon thickness. I use your suggested method (AKA a stub tenon) when I make solid doors that will have a natural finish i.e. not painted, as I prefer the aesthetics. Will probably do a video on that process at some point, so stay tuned 😁 👍
@lucianosalt2396
@lucianosalt2396 6 лет назад
Hi loving the videos, what extraction do you use in the workshop to effectively remove the MDF dust?
@10MinuteWorkshop
@10MinuteWorkshop 6 лет назад
Thanks! I have an old Festool, CTL 22 as the main shop vac, and a CTL Midi dedicated to the mitre saw. Good vacs 👍Oh, and all wood dust is hazardous, not just MDF, btw.👍
@rzholland
@rzholland 6 лет назад
2 Questions - How do you stop your router turning when tightening the bit retaining nut, I have a Trend T10 and the only way of stopping it is holding in the button on the side - How have you arranged the raising and lowering of your router - Cheers Robin
@10MinuteWorkshop
@10MinuteWorkshop 6 лет назад
It’s the big Triton router slung under the bench, it auto-locks the shaft when the collet reaches full extension. And for raising & lowering I just reach under the bench and turn the knob. Later versions of this router had ‘above bench’ adjustment via a handle. 👍
@rzholland
@rzholland 6 лет назад
That auto lock does sound handy. I have realised since that I should have bought a T11 not T10 as you can alter the height from above - Hey Santa are you listening!!!
@10MinuteWorkshop
@10MinuteWorkshop 6 лет назад
Yes, the T11 is meant as a bit more of a bench/table mounted router - I have one as a trial right now, and it's quite a lump hand-held 👍
@michaelburton9638
@michaelburton9638 5 лет назад
@@10MinuteWorkshop yeah I was wondering that too , I've got a router table with a big trend router in it and have to reach under to lock it which is a real pain in the ah ha ha ha
@housechase
@housechase 6 лет назад
Hello Peter, just watched the "raised panel door video and I am impressed I am going to make a bedroom wardrobe with six MDF doors 2100 X 600mm and the original plan was to have 9mm MDF inserts around a 25mm thick poplar softwood frame. Would that size door work, all MDF, with all the panels glued up using your video method or is the door too long? Thanks
@10MinuteWorkshop
@10MinuteWorkshop 6 лет назад
Hi Paul. Yeah, 2100 x 600 is a pretty big door. Sorry, but did you mean to make a raised panel door as in this video, or a shaker-style loose tenon door with a 9mm panel? A raised panel door is going to be pretty heavy, but 25mm rails & stiles (mid- rail at that size, obvs) and a 9mm panel should be fine. Don’t know where you’d buy your MDF from, but worth checking that it’s nice and flat for those rails and stiles. 👍👍
@housechase
@housechase 6 лет назад
Thanks for your reply Peter, thinking about weight I will revert back to poplar stiles and rails and a 9 or 12mm MDF insert shaker style door and use the raised panel idea on another project
@virtuaviolin
@virtuaviolin 5 лет назад
Great video tutorial, thank you very much for sharing. I would like to ask you a question: I want to build my kitchen doors in MDF and I see that it is almost always done by assembling parts, could not it be done directly by routing an entire panel to give relief?
@10MinuteWorkshop
@10MinuteWorkshop 5 лет назад
Thanks! It’s so-able, but unless you can spend time squaring off the corners of the routes relief, it won’t look great. But it can be done, yes. 👍
@annehanda475
@annehanda475 5 лет назад
Hi, how do I stop MDF doors from warping, my small kitchen doors are fine but the tall doors see to have warped.
@10MinuteWorkshop
@10MinuteWorkshop 5 лет назад
What thickness MDF? Was it MR MDF or regular? Painted both sides or just one? Laid flat/on edge to dry, or just leaning? IME a 22mm rail & stile door from MR MDF won't warp / bend after painting if it's laid flat or on edge to dry. HTH P
@Asta-wl8jz
@Asta-wl8jz 7 лет назад
I have never seen an MDF cabinet door before. It is a waterproof MDF though. I don't think I've ever seen it here in Texas....I'll look. Thanks for your videos that was quite informative. Do the hinges do ok in MDF or do they loosen up after time?
@10MinuteWorkshop
@10MinuteWorkshop 7 лет назад
Asta Not waterproof, but 'moisture resistant' , or MRMDF - very common in the UK and Europe. Euro-style concealed hinges hold up very well over time, no problems at all as long as you,use a decent brand. 👍
@muffinsmeow
@muffinsmeow 7 лет назад
Go to Home depot and Loews, they are selling MDF
@barryhayward2911
@barryhayward2911 3 года назад
Hi Peter, Another excellent video. Previously made standard Shaker style doors using different techniques but after watching your video thought I'd give the loose tenon technique a go - very impressed thanks very much. My only question is with regard to your grooving bit. Mine is a Trend one and only provides a 10/11 rebate from memory, where as yours appears to be deeper. Can you tell me the make/spec of it? Thanks again for the excellent videos
@10MinuteWorkshop
@10MinuteWorkshop 3 года назад
Thanks Barry. Links are in the video description - these ones were from Wealden tool. Heavy duty groover - goo.gl/Ht1TU4 Arbor for above - goo.gl/xdE9PU Panel raising bit - goo.gl/GceCdJ
@barryhayward2911
@barryhayward2911 3 года назад
Many thanks Peter, much appreciated. Keep up the good work. I'll remember to check the links next time 👍
@5e34nut
@5e34nut 7 лет назад
Hi Fantastic job as always Can you do a video on euro hinges please I'm forever out by mill or two many thanks
@10MinuteWorkshop
@10MinuteWorkshop 7 лет назад
Thanks! Not sure I could do an entire vid on euro hinges, but I'm doing some wardrobes this week, so I'll put in an extra little section on the hinges in there, OK? Cheers, P
@5e34nut
@5e34nut 7 лет назад
I thank you for your rapid reply please continue with the fantastic videos A real pleasure and informative
@thomasclarke7611
@thomasclarke7611 4 года назад
Hi Peter...brilliant videos. I was wondering what setup you use to adjust the height of your router? Thanks, Tom.
@10MinuteWorkshop
@10MinuteWorkshop 4 года назад
Thanks Tom! In the table? I’ve taken the springs out, and just use a firm shove from underneath to get it to slightly over the right height, then fine-adjust it down to the correct depth of cut. Slightly newer versions of my router (Triton TRA001) have above-table adjustment, but this one doesn’t. And yes, I only discovered that after I bought it! 😂🤷‍♂️
@MREJ63
@MREJ63 7 лет назад
Great video - thanks. I was just wondering which Router you had as guide to the type of Router you would need to do this kind of work, especially the Raised Panel part with such a large bit?
@10MinuteWorkshop
@10MinuteWorkshop 7 лет назад
Thanks! I have a big old Triton slung under the workbench - it's been there so long I'd have to check to see what model number it is I'm afraid! But yes, you need a 1/2" router with some grunt to use a panel raising bit. Cheers, Peter
@HamidKhan-po1px
@HamidKhan-po1px 5 лет назад
Beautiful work. Do we need wood beading as a frame to give more strength? Or is it enough..
@10MinuteWorkshop
@10MinuteWorkshop 5 лет назад
Thanks! No, beading is for aesthetics only. Plenty strong enough as it is👍👍
@HamidKhan-po1px
@HamidKhan-po1px 5 лет назад
@@10MinuteWorkshop thanks...
@AliHasan-us4jq
@AliHasan-us4jq 3 года назад
Wow...
@martinurquhart7112
@martinurquhart7112 7 лет назад
Hey Peter. I think that I have watched pretty much all of your videos and have revisited this one a couple of times to prep for a cabinet and drawer set build this weekend. Thanks for all of the instructional stuff - it is super useful for someone with limited experience like me. I love it all; please keep up the good work and I hope that you will extend your experiment past its year deadline. If you have the time, can you help with a couple of questions please? 1. Is the Junckers lacquer the ProFinish one? Do you bother with the PreLak? 2. From this and your saker door video - why do you use MR MDF? and why 22mm over 18mm (more meat for the Blum hinges?)? Cheers M
@10MinuteWorkshop
@10MinuteWorkshop 7 лет назад
+Martin Urquhart Hi Martin, and thanks! The Junkers lacquer I use is this one:- www.decoratingdirect.co.uk/viewprod/j/JUNSTG/ in semi-matt finish. And no, I don't bother with pre-lak, not on a drawer-box. I use MR MDF because it's a much better quality board for not much more money - seriously, if you haven't tried it, give it a go. And 22mm over 18, simply because it has a bit more heft to it - makes the doors a bit beefier, especially bigger wardrobe doors. HTH 👍 P
@martinurquhart7112
@martinurquhart7112 7 лет назад
Thanks Peter.
@markhaley4952
@markhaley4952 4 года назад
Great video Peter I am new to your tutorials and have just converted part of my garage into a workshop for my 3d printing and laser cutting machines also for woodworking as well. Have one question for you what sash clamps are you using and if possible where to buy some.
@10MinuteWorkshop
@10MinuteWorkshop 4 года назад
Thanks Mark and welcome. All my sash clamps are cheap & cheerful ones, either silverline or unbranded ones from eBay. There are links at the ‘stuff I use’ section of the companion website at 10minuteworkshop.com 👍👍
@andrewlawrence990
@andrewlawrence990 3 года назад
What was the brand name of your manual mitre saw?
@10MinuteWorkshop
@10MinuteWorkshop 3 года назад
It’s an old Nobex ProMan. Great saws. 👍
@sanbucaone
@sanbucaone 6 лет назад
Hi Peter, the link for the medium raised panel cutter gives the choice of three. What is the part no of the one you use? I can’t see a bearing I guess that would restrict the tongue size on this application. Finally ... I have the tritón router mof001 which I believe is 2 hp would this be up to the challenge of the panel cutter? Many thanks Peter as always Great instructional video. 👍
@10MinuteWorkshop
@10MinuteWorkshop 6 лет назад
I used the T1930 - all depends on wether you want a straight edge or one with a radius, that's the only difference between the bits on that page. And no, no bearing on these as it would interfere with the cut. I have the same Triton slung under my bench - works great 👍
@sanbucaone
@sanbucaone 6 лет назад
Many thanks for quick response. Cheers Peter.
@didanoff
@didanoff 3 года назад
Thanks for the video. Do you use any dust collector with vacuum?
@10MinuteWorkshop
@10MinuteWorkshop 3 года назад
No, just the L-class Vacuum. 👍
@didanoff
@didanoff 3 года назад
@@10MinuteWorkshop do you use filter bags?
@ug45cwb
@ug45cwb 3 года назад
Good method, but why don't you just stop the grooving bit before the end on the horizontal panels, save the need to have loose tenons?
@10MinuteWorkshop
@10MinuteWorkshop 3 года назад
Thanks! And because loose tenons are the dmfasrest easiest way to make a panel door, by far. 👍
@ug45cwb
@ug45cwb 3 года назад
@@10MinuteWorkshop I don't understand. Using this method you have to make to loose tenons, then glue them in, cut them to size then sand them down. As opposed to simply stopping the grooving bit a little bit before you reach the end!
@EdwardT9
@EdwardT9 3 года назад
@@ug45cwb you need to hold the rails and stiles together with something other than the panel, otherwise the door falls apart in time. The 4 tenons do that.
@glenwelder
@glenwelder 4 года назад
How do you hinge your saw track to your work bench, it seems to make square cuts so easy.
@10MinuteWorkshop
@10MinuteWorkshop 4 года назад
It’s an off-the-shelf Festool MFT or Multi-function table & the hinged rail comes as standard. See videos #182 and #183 for more details. 👍
@houma1984
@houma1984 4 года назад
You have a new subscriber, thank you for this beautiful video, can you recommend a router table? Im trying to do a small project by my house, and i would like to make my doors cabinets by my self, thank you!
@10MinuteWorkshop
@10MinuteWorkshop 4 года назад
Thank you and welcome! I’ve honestly never used a commercial router table, but the Trend ones seem decent enough. 👍👍
@thomaskitchin3517
@thomaskitchin3517 7 лет назад
Dear Peter, thanks very much for these excellent videos. Very helpful! Could I ask how you prep/finish the routed into mdf for the panel cuts? Many thanks Tom
@10MinuteWorkshop
@10MinuteWorkshop 7 лет назад
Thomas Kitchin My pleasure, thanks for watching! I have a painting & finishing video planned, but short answer is I usually use a water-based acrylic primer/undercoat, followed by a water-based topcoat, usually in an eggshell finish. Cut edges of the MDF gets two coats of primer with a thorough sanding after the first one, and usually two or three topcoats, all applied with a foam roller. HTH Peter
@thomaskitchin3517
@thomaskitchin3517 7 лет назад
Thanks! I'm a water based convert (well (90% of the time) but think its the sanding back technique I need to crack to really get a top finish. Thanks for the heads up on the finishing vid looking forward to it! Very best Tom
@blackadder1966
@blackadder1966 7 лет назад
Peter Millard i was just about to ask about painting too.
@10MinuteWorkshop
@10MinuteWorkshop 7 лет назад
I'm working on it, I promise!
@michaelodonovan1908
@michaelodonovan1908 7 лет назад
Sorry really stupid question but what is the Festool hinge about? I can't find it on the net anywhere, just the saw and rail for sale.
@10MinuteWorkshop
@10MinuteWorkshop 7 лет назад
HaHa - understand completely! It's a Festool Multi Function Table, or MFT for short; the hinged rail comes as part of the package. Festool will sell the spare parts to put your own together, but at a pretty steep price unfortunately. If you have the time check out my Festool vs Cheap Tool video 3-parter on the tracksaw; at the end of that I explain I'll be doing a 'tracksaw workshop' series, and a mobile workbench with a hinged rail assembly is part of that plan, provided I can make it work! 👍
@marppp28
@marppp28 5 лет назад
Hi it’s nicely done, just wondering where did u get moisture resistant mdf?
@10MinuteWorkshop
@10MinuteWorkshop 5 лет назад
I get mine from a local timber yard, (ajferguson.co.uk) but you can get MR MDF in lots of places - where are you based?
@marppp28
@marppp28 5 лет назад
I’m in norwich, can’t buy 9mm in many places mostly 18mm
@redsam6881
@redsam6881 4 года назад
I have tried to make molding out of MDF - The profile coves & beads always comes out fuzzy & would require tons of prep to get a smooth painted finish - what am I doing wrong? Thanks for any help!!
@10MinuteWorkshop
@10MinuteWorkshop 4 года назад
You need to use MRMDF - Moisture Resistant - much better quality board for not much more money. 👍👍
@glumberty1
@glumberty1 7 лет назад
Could I do this with regular MDF or ultralight if I paint it? I've never seen moisture resistant MFD before.
@10MinuteWorkshop
@10MinuteWorkshop 7 лет назад
glumberty1 Haven't used regular MDF for a long time - I'm sure it would work, but I suspect you'd need to do a lot of prep on the cut edges before painting, e.g. a shellac-based primer like Zinnser Bin. If you try it, let me know how it works out 👍
@alaskanawesomeness9017
@alaskanawesomeness9017 7 лет назад
I am curious why you use MDF? Over here it is Garbage wood. Great video!
@10MinuteWorkshop
@10MinuteWorkshop 7 лет назад
Alaskan Awesomeness Over here (UK, Europe, Oz, NZ etc...) it's the mainstay of the fitted furniture business - a flat stable board that machines easily and takes paint well, widely available in different thicknesses. Just to be clear, this is MR (moisture resistant) MDF - different animal altogether from what you might be used to. And thanks! 👍
@alaskanawesomeness9017
@alaskanawesomeness9017 7 лет назад
I figured it had to be better than over here but was just checking. Thanks
@10MinuteWorkshop
@10MinuteWorkshop 7 лет назад
Alaskan Awesomeness My pleasure. I think I may have to do a quick video about MDF... 👍😬
@craigcoe2804
@craigcoe2804 6 лет назад
Hi Peter, just curious as to whether you have a variable speed router or not? If not, how easily/safely does the raised panel cutter cut mrmdf. I have a fixed speed (28000rpm) makita router and didn't want to try it at that speed!! I'm a one man band cabinet maker myself and your videos are great!
@10MinuteWorkshop
@10MinuteWorkshop 6 лет назад
Hi Craig. it is variable speed, but I have it set permanently to 11 😬 I probably should have slowed it down some, for a bit that size, but it worked fine in MR MDF - though as always, run a test cut or two first 👍
@craigcoe2804
@craigcoe2804 6 лет назад
@@10MinuteWorkshop thank you - I had hoped this was the answer! That saves me borrowing / buying a new router. It'll be a brand new bit if I do go down this route (depending what the customer wants) so at that rate it should be ok 😬. I'm also about to place an order for the fence dogs - what a great idea!
@10MinuteWorkshop
@10MinuteWorkshop 6 лет назад
Pleasure - let me know how you get on! And yes, fencedogs are such a great idea - be sure to mention my name when you order! 👍😆
@tjbrison
@tjbrison 5 лет назад
I really, really, wouldn't run a large panel bit at 28K RPM - this would produce very high tip speeds. If you have a saw table, raised panels can be made very easily, or failing that, use a straight cutter and an incline jig to get the same result.
@10MinuteWorkshop
@10MinuteWorkshop 5 лет назад
@@tjbrison Are you in the US Tim? Here in the UK any commercial workshop running an unguarded blade can find themselves liable to a 5-figure fine, as it's considered one of the most serious breaches of health & safety regulations. So with respect, I really, really wouldn't recommend that method, here. I don't disagree with you re the router speed - I should have slowed it down - but it worked fine in MR MDF. Plus the OPs post is from 2 months ago, so pretty sure the job's been done. 👍
@luisromero3734
@luisromero3734 7 лет назад
Very very very well explained!!!! Now, how do you avoid having the end grain show after it's been painted? How do you seal it? Thanks!!! I just subscribed to your channel
@10MinuteWorkshop
@10MinuteWorkshop 7 лет назад
Luis Romero Thank you! With MDF (especially MR MDF) there's no end grain, as such, so I use my regular method of a couple of coats of water-based acrylic primer/undercoat, (usually) followed by a couple of coats of water-based eggshell. Thorough rub-down between coats, of course. I'll be doing a 'painting and finishing' video before too long, so stay tuned for that, and thanks for watching! P
@luisromero3734
@luisromero3734 7 лет назад
Peter Millard thanks for your response... i will be on the watch for your next videos. Thanks!!!
@couplandsj
@couplandsj 7 лет назад
Peter, I was going to ask about your painting process and what brands of primer & paint you use, so will wait with baited breath for this video...;-) I'm planing on painting some of my workshop cabinets so am looking for a paint/finish that is hard wearing..any tips on that will be very welcome.
@10MinuteWorkshop
@10MinuteWorkshop 7 лет назад
Simon Coupland Thanks! Paint brands are almost always either Dulux or Leyland, water-based acrylic paints and usually in an eggshell finish, though I have some satinwood coming up - honestly, I don't know how I'm going to cope, lol!
@saeed6811
@saeed6811 5 лет назад
Can I do this job with the Bosch miter saw? I am new to wood work but already bought a bosh beveled miter saw, Bosch table saw. Also I want to buy some Kreg pocket hole tools. Are they ok for MDF?
@10MinuteWorkshop
@10MinuteWorkshop 5 лет назад
Hi. You could cut the rails and stiles to width with a table saw, and to length with a mitre saw, but you’ll want a router in a table to cut these grooves safely. Not really a pocket-hole user, but the times I’ve used them I’m MDF they’ve been fine, though a lot will depend on what you’re using them for, exactly. 👍👍
@drewbs86
@drewbs86 7 лет назад
Hi Peter, really enjoying your videos! Do you ever use tulipwood? I ask because I see a lot of Americans use this (poplar to them) and I wondered how available it is here in the UK, and how it compares to the MRMDF? Thanks
@10MinuteWorkshop
@10MinuteWorkshop 7 лет назад
drewbs86 Thanks! I haven't used tulipwood, no, as my local timber yard don't stock it. I think Ash might be more widely available, but I don't use a lot of natural timber so wouldn't want to say for sure. You'd need to allow for some movement with either of them, of course,, but I would absolutely expect it to be harder-wearing than MR MDF; if the finished piece is to be painted, I guess the question would be, how much harder-wearing do you really need? For example, I've been making these doors out of MR MDF for ~15 years or so and haven't had a single failure. Literally, not one. Great question though - I think I have one more door video in me, and this may be a good thing to add into the mix! 👍 Thanks, Peter.
@drewbs86
@drewbs86 7 лет назад
Thanks for the reply Peter, that's really helpful information. I haven't seen see you mention your timber supplier, do you use a local independent? I think that would be a really interesting video to watch! All the best
@10MinuteWorkshop
@10MinuteWorkshop 7 лет назад
My pleasure. I do use a local independent - hoping to do a little video with them before too long actually, been slightly delayed as they're just investing in a big CNC, and understandably are keen to have that featured. They're a great yard - ajferguson.co.uk over 100 years old - and literally 5 minutes from me. I know from comments here that I'm very fortunate to such a good place so handy; there are always alternatives, but they've helped me out more than once and are a great bunch of guys. Recommended, if you're anywhere in West London 👍
@salvatoregagliardi48
@salvatoregagliardi48 4 года назад
Is that the 3-1/4hp Triton router?
@10MinuteWorkshop
@10MinuteWorkshop 4 года назад
It’s the big Triton, yes, the TRA001. 👍
@xw6968
@xw6968 7 лет назад
Ofcourse im not a pro but i hear a lot of warning talks about MDF and health. Have a mask on and watch out for the dust of it.. Are there different kinds of MDF or ?.
@10MinuteWorkshop
@10MinuteWorkshop 7 лет назад
+xander witt All wood dust is hazardous. Dust extraction at the tool is always better than a face mask, and ideally air scrubbers running to pick up the fine dust. Check out my recent workshop tour video for more info on the dust extraction/collection. And yes, there are many grades of MDF 👍
@GrahamOrm
@GrahamOrm 7 лет назад
Peter, nice job. I'm thinking seriously about the Domino machine. However, I'd want it to make bigger items such as garden gates. Do you think the 500 could cope with that or would it be wiser to get the 700?
@10MinuteWorkshop
@10MinuteWorkshop 7 лет назад
+Graham Orm Thanks! In an ideal world you'd have both; I have twitter pals who have the 700 and wish they had the 500 for smaller stuff, because the 700's a much bigger machine. I made some French doors with my 500 - bought it for that job specifically and the job paid for it, basically - and they've held up well, but I think for garden gates etc... you'd want the 700. Depends what the bulk of your work is, I guess??
@GrahamOrm
@GrahamOrm 7 лет назад
As you say ideally both machines, but I certainly couldn't get that past the committee. Hmmmm, I'll have to think. Initially it's for a pair of hefty Iroko gates, after that who knows? How deep will the 500 plunge?
@10MinuteWorkshop
@10MinuteWorkshop 7 лет назад
+Graham Orm Max plunge in the 500 is 25mm, for the 50mm doms. Sounds like you need to aim for the 700 tbh - and honestly, once you have it, you'll use it 👍
@GrahamOrm
@GrahamOrm 7 лет назад
Thanks for the feedback Peter.
@blackadder1966
@blackadder1966 7 лет назад
i can get 18mm mr mdf but next step up is 25mm would that be too much for rails and stiles?
@10MinuteWorkshop
@10MinuteWorkshop 7 лет назад
Hi. 25mm is a little bit heavy - you'll be at or close to the limit of most concealed hinges, for example - though it depends on the size of your doors, of course. I find 22mm to be the sweet spot for the kind of doors I do, but for larger doors, if the choice was 18mm or 25mm, then I'd go 25mm, provided the hinges were OK. Cheers, Peter
@PitmanCabinetmaking
@PitmanCabinetmaking 7 лет назад
Blum make a hinge suited for thicker panels such as 25mm
@10MinuteWorkshop
@10MinuteWorkshop 7 лет назад
PitmanCabinetmaking 👍
@sburge1989
@sburge1989 5 лет назад
Would you be able to make a door like this from a single mdf piece on the CNC?
@10MinuteWorkshop
@10MinuteWorkshop 5 лет назад
Theoretically, yes - you’d need a CNC big enough to do it, obviously - but the biggest issue would be that you’d be exposing a lot of the MDF core on the panel, which isn’t the best of materials, so could be tricky to finish. 🤔🤷‍♂️👍
@sburge1989
@sburge1989 5 лет назад
@@10MinuteWorkshop worth a try with your new cnc? Just to test and compare maybe
@10MinuteWorkshop
@10MinuteWorkshop 5 лет назад
Yes, when it’s finished, absolutely. 👍
@blackrainb0w
@blackrainb0w 7 лет назад
Hi Peter, great videos on the MDF doors, will definitely try this method. May i ask where you bought the part that splits your dust extraction hose into two at 1:47. I was after something similar.
@10MinuteWorkshop
@10MinuteWorkshop 7 лет назад
Thanks! I've had the Y piece for so long I don't remember where I bought it, I'm sorry - probably eBay or Amazon. It's a waste hose fitting from a caravan, I seem to remember. I'm away just now, but I'll have a dig around and see if I can find a link when I'm back. 👍
@blackrainb0w
@blackrainb0w 7 лет назад
Thanks Peter.
@10MinuteWorkshop
@10MinuteWorkshop 7 лет назад
Yep, it's a 28.5mm waste hose connector, bought mine off eBay, like this one:- goo.gl/Xxsj1n HTH. P 👍
@blackrainb0w
@blackrainb0w 7 лет назад
Excellent! Thanks Peter.
@JBSeymour
@JBSeymour 7 лет назад
subscribed! where do you live out of interest (no great disparity in humidity?)
@10MinuteWorkshop
@10MinuteWorkshop 7 лет назад
thesey Thanks! I live and work in London, UK.
@petesoebekti2022
@petesoebekti2022 4 года назад
what brand of router do you use ? :)
@10MinuteWorkshop
@10MinuteWorkshop 4 года назад
Under the bench? It a big old Triton TRA-001 - particularly good as the plunge is deep enough for the colt to clear the bench. 👍👍
@luisromero3734
@luisromero3734 7 лет назад
Very very very well explained!!!! Now, how do you avoid having the end grain show after it's been painted? How do you seal it? Thanks!!! I just subscribed to your channel
@alth1586
@alth1586 2 года назад
why wouldn't you just use a solid piece of mdf and rout the retail ?
@10MinuteWorkshop
@10MinuteWorkshop 2 года назад
Take a look at the profile, then tell me what cutter you had in mind… 🤷‍♂️
@johnchown3539
@johnchown3539 5 лет назад
Where can I purchase MDF in the south east of England that’s good quality
@10MinuteWorkshop
@10MinuteWorkshop 5 лет назад
The South-East’s a pretty big area! I buy mine locally, from www.ajferguson.co.uk, but they only deliver in London. I’m sure there are plenty of suppliers - look for Medite or Caber brands of MR MDF, they’ve always been solid when I’ve used them. 👍👍
@johnchown3539
@johnchown3539 5 лет назад
Thank you Peter, love the show.
@thesparky61
@thesparky61 4 года назад
were do you buy mr mdf
@10MinuteWorkshop
@10MinuteWorkshop 4 года назад
I buy from a local timber yard, ajferguson.co.uk. Great yard, great guys. 👍👍
@paulelliott4954
@paulelliott4954 7 лет назад
Hi Peter. Can you let us know where you buy your mr mdf thanks
@10MinuteWorkshop
@10MinuteWorkshop 7 лет назад
Paul Elliott Hi Paul. I buy mine from a local timber yard - www.ajferguson.co.uk - who are very good, although AFAIK most decent yards will stock MR MDF. If you're in the U.K. (sorry, can't tell) you can also buy it from Wickes, Travis Perkins, Builder Depot, some B&Q branches, all the usual suspects - though I'd always advise seeking out a local timber yard as you'll get better service (and often prices) from them, as well as them being far more knowledgeable, and generous with their advice. HTH, Peter👍
@paulelliott4954
@paulelliott4954 7 лет назад
Thanks Peter. I am in Mansfield, Nottinghamshire
@10MinuteWorkshop
@10MinuteWorkshop 7 лет назад
+Paul Elliott Not my beck of the woods so can't advise in a local yard, but a quick Google should throw up some likely suspects 👍
@andycaudwell2583
@andycaudwell2583 7 лет назад
Hi Paul I Live In Mansfield Too Have You Tried Rainworth Fencing Ask For Craig
@paulelliott4954
@paulelliott4954 7 лет назад
Thanks Andy will do
@ihaulscrap
@ihaulscrap 7 лет назад
Where did you get the router bit and what brand is it?
@10MinuteWorkshop
@10MinuteWorkshop 7 лет назад
I get pretty much all my bits from wealdentool.com - outstanding quality and service. The panel raising bit is here - goo.gl/GceCdJ Incidentally, there are links to the majority of the items 'used/featured in this video' in the vid. description, directly beneath the video (click 'show more' if you don't see it) and a full list of 'stuff I use' at www.10minuteworkshop.com.
@ihaulscrap
@ihaulscrap 7 лет назад
Thanx. Very helpful.
@ihaulscrap
@ihaulscrap 7 лет назад
Crap they don't ship to Canada.
@10MinuteWorkshop
@10MinuteWorkshop 7 лет назад
Hmmm - I wasn't aware of that. I've shot them a quick email asking them to confirm, and will post back here. Could be they just don't list shipping outside the EU on their site, or it could be that they've decided shipping relatively small items over large distances isn't worth the hassle, of course... I'll post the response when I get it. 👍
@ihaulscrap
@ihaulscrap 7 лет назад
They said it was bc of insurance reasons.
@hishamk.b5175
@hishamk.b5175 7 лет назад
well don
@10MinuteWorkshop
@10MinuteWorkshop 7 лет назад
hisham k.b Thank you!
@dhatchbernier
@dhatchbernier 4 года назад
Nice work, but dear god I hate raised panel doors and MDF.
@10MinuteWorkshop
@10MinuteWorkshop 4 года назад
Thanks! Well, MR MDF is a slightly different animal, but yes, console the agree re raised panel doors! 😂👍
Далее
How To Make A Raised Panel Cabinet Door
18:54
Просмотров 211 тыс.
🎙Пою РЕТРО Песни💃
3:05:57
Просмотров 1,3 млн
How to paint MDF - DIY tips!
24:05
Просмотров 1,2 млн
Shaker-style doors in MDF [video 405]
9:48
Просмотров 98 тыс.
Painting MDF Doors [video 407]
17:26
Просмотров 551 тыс.
How To Make Raised Panel Doors on a Router Table
15:15
Raised Panel Cabinet Doors in MDF [*Ad] [video 548]
10:26
Cabinet Door Sizing [*Ad] [video 549]
13:15
Просмотров 98 тыс.
MDF shaker doors / how to make shaker doors
15:08
Просмотров 282 тыс.