How to Make TDA2030 Stereo Amplifier | Tda2030 Amplifier Module

Подписаться 16 тыс.

Просмотров 26 тыс.

50% 1

How to Make TDA2030 Stereo Amplifier | Tda2030 Amplifier Module
TDA2030 Module Description:
1. On-board TDA2030A audio power amplifier chip.
2. Mono 18 w power amplifier circuit design.
3. On-board speaker terminal block
4 On-board 10k adjustable resistance, can adjust the volume of the amplification.
5. On-board power light.
6. Chip has lead to the main pin, can directly input audio signal.
7. Working voltage: 6 -12 v.
8. Board size: 31.6 (mm) x23.2 (mm).
Components Needed:
1. Tda2030 amplifier module
2. Heatsink
3. Wires
4. Sound speaker
5. DC socket
6. Audio Jack
7. 12v adaptor
8. Soldering
Subscribe to my channel and click the bell button to be updated on my next video. Thank you for watching♥️Enjoy and have a great day.
Subscribe to this channel: / javiersdiy
Related DIY videos:
DIY RC Car from Cardboard:
• How to Make RC Car Fro...
DIY 12v Power Supply:
• How to Make 12v Power ...
DIY 13000 mAh Powerbank:
• How to Make a 13000 mA...
DIY Sander Disk from Old DVD/CD player:
• How to Make a Mini San...
3 in 1 Power Supply:
• How to Make a 3 in 1 P...
DIY VU Meter:
• How to Make a VU Meter...
DIY Face shield:
• How to Make DIY Face S...
DIY Tester:
• How to Make Test Light...
DIY Flashlight:
• How to Make Emergency ...
DIY RC Car:
• How to Make RC Car Fro...
DIY Generator:
• How to Make Generator ...
DIY Air Cooler:
• How to Make a Powerful...
DIY Water Pump:
• How to Make Powerful W...
DIY Air Pump:
• How to Make an Air Pum...
#TDA2030amplifier
#TDA2030StereoAmplifier
#TDA2030amplifiermodule

Опубликовано:

6 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 63

@veyselyazc2879 2 года назад

Bravo👏👏👏

@amitghosh6966 2 года назад

What should be the heatsink size (length and width) for single tda2030A ic if it is to deliver 10 watts@4 ohms on 12-0-12 V transformer supply ?

@JaviersDIY 2 года назад

Just to be sure sir please put a fan so that the heat will normalize

@BrianCraigKeith31mm 3 года назад

Thanks again. Great video.

@JaviersDIY 3 года назад

Thank you sir

@info_bits 2 года назад

This gets very hot.

@JaviersDIY 2 года назад

That's why i put a bigger heatsink sir.

@MACFiFth 2 года назад

i got this amplifier module too and the power output was 15 watts at 4 ohm unlike the one in datasheet and the IC was TDA2030a so i would say that the fake tda2030a soldered in the module has the same specs of original tda2030 also use 470uF 25v Capacitor or 1000uF 25v for better results on the output of module (replacing capacitor) its just worth $1

@JaviersDIY 2 года назад

As you can see on the module sir it's looks small so it means the output wattage will be also small.

@gilman7608 2 года назад

Is 1000uf 25v really improve performance? I read somewhere it increases the base

@JaviersDIY 2 года назад

@@gilman7608 no sir.

@kerimcls 2 года назад

Can we plug one 10k potentiometer into two circuits?

@JaviersDIY 2 года назад

Yes sir. You can

@kerimcls 2 года назад

@@JaviersDIY how about?

@anti_mainstream6960 3 года назад

I use this modul with a 5 inch 20 watt 6 ohm speaker plus tweeter. At below half volume the sound feel good. But when I turn the volume over half the sound become bad. Do you know why this happen? Thx

@JaviersDIY 3 года назад

Because of your powersupply.

@anti_mainstream6960 3 года назад

@@JaviersDIY then how much minimal current need??

@JaviersDIY 3 года назад

3-5 A

@MACFiFth 2 года назад

@@JaviersDIY actually you can use 20v 1a or 14v 1.5a or 20 watts of power supply.

@asuspentium4 2 года назад

So does there have to be a jumper between vcc, gnd (signal) and gnd (power) of each module? the only one that does not have a bridge is In+? Thank you.

@JaviersDIY 2 года назад

No sir. Just look my connection again. Thanks

@asuspentium4 2 года назад

@@JaviersDIY I already saw it, you joined vcc + with vcc + then current negative with current negative and finally signal negative with signal negative, then you joined that signal negative bridge with the gnd of the jack and L and R of the jack with each positive signal (in+).

@JaviersDIY 2 года назад

@@asuspentium4 yes correct sir.

@karthikeyankarthikeyan5886 11 месяцев назад

Hi sir 12 volt transformer power supply ok or 12 volt adaptor

@JaviersDIY 11 месяцев назад

any of that supply sir as long as the current is sufficient

@satyajeetpatra7920 3 года назад

Sar mono 2 channel stereo diagram bataiye

@JaviersDIY 3 года назад

Please speak english for better understanding sir.

@aksinstituteoflearningengl7176 Год назад

Sir can i run this module on 9 volt with a 4 inch speaker

@JaviersDIY Год назад

No sir

@aksinstituteoflearningengl7176 Год назад

But this module is from 6-12 volt Then it must be run on 9 volt

@aksinstituteoflearningengl7176 Год назад

@@JaviersDIY sir could you please suggest a 9volt amplifier module running with a bettery

@mltube9975 2 года назад

Any heat problem?

@JaviersDIY 2 года назад

The heat is normal sir it is because I put a bigger heatsink

@SSchannel_353 2 года назад

Sir how many amps it would require minimum

@JaviersDIY 2 года назад

2 amperes sir

@ManinderSingh-ox4uf Год назад

What is watt of the speakers

@JaviersDIY Год назад

50W sir

@kirildimitrov1912 2 года назад

How many volts are they?

@JaviersDIY 2 года назад

12V sir

@poketamizha3708 3 года назад

Bro can i use 5v 1a will it give full output?

@JaviersDIY 3 года назад

No sir. Less input also have less output.

@djnoisechile Год назад

se escucha pesimo, es el microfono de la camara cierto ?

@JaviersDIY Год назад

For better understanding please use the universal language

@djnoisechile Год назад

@@JaviersDIY español latino es el universañ, qie te ciesta traducir

@rampr735 Год назад

Yah do speaker bajar sakta hai

@JaviersDIY Год назад

For better understanding please use the universal language

@erwinkarsindu2127 11 месяцев назад

Maaf seblmnya kak.. Terlalu cepat.. sy yg pemula bingung apalagi tdk tdk ada kata2 nya.. mana yg + mana yg - kabel jg banyak gk tau arusnya kak ?! 😭😭😭😭😭

@JaviersDIY 11 месяцев назад

for better understanding please use the universal language