How to modify fsia6b receiver to get battery voltage telemetry

Подписаться 464 тыс.

Просмотров 39 тыс.

50% 1

My rc video playlist
👉 • Rc video playlist
Hello friends today in this video i have shown how to modify flysky fsia6b receiver to get battery voltage telemetry on the transmitter. Normally the receiver voltage shown on the fs-i6 transmitter is the BEC voltage we feed to the receiver. Which is useless as we all know the voltage of a BEC which connected to receiver. But with this modification we can get real-time battery voltage in our transmitter. It will be very helpful if you don't use any external telemetry device.
Please take help from a skilled person if you have bad soldering skill.
Thank you very much for watching
if you have enjoyed this video then please like, share, comment and don't forget to subscribe.

Опубликовано:

14 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 48

@magneresjuan 2 года назад

Hello ! Great vid. I conect oposite voltage baterry to my fs ia6 receiver AND saw smoke... any ideas for the repair

@anhntcover7971 5 лет назад

Simple, concise, awesome 😆

@PeterAbt 4 года назад

Do you know if there is any way to turn of the Voltage Alarm? Because when I have my motor on - full throttle the voltage drops down quiet drastically - so low - that the alarm goes off. But I want to keep the high- low-voltage settings so that there I can keep the beautiful battery animation at the top right corner of the display. Besides that: Thank you for the video was a great help and works flawlessly!

@ashishpawar2261 3 года назад

Great video, it's working perfectly, thanks for such informative video

@rcbuildmaster6192 4 года назад

Nice info , but I think we get flysky voltage sensor which can connect to ibus sensor port directly on FSIA6B

@yashsoni7137 3 года назад

It will distroye your rx

@Baz4antify 3 года назад

Awesome video! Thanks, I'm going to make this modification!

@feltav5719 2 года назад

After this mod can you still get altitude telemetry as well as the rx voltage?

@mush0847 3 года назад

The specification shows 4.2 to 6.5v max, but 11v battery can be used?

@dominikap.7399 4 года назад

What parameters to set on the transmitter for the 11.1V battery? How much for low, high and for alarm? The alarm rings even at full battery.

@marinaartandcraft8662 5 лет назад

Bhai mere pas ek transmeter hai jisme 16mhz crystal laga huaa hai jo programmable nahi hai. Ye kis resiver ke sath binde karega.

@demodelbouwloods987 Год назад

how much voltage can it handle? can it handle a 6s battery?

@harrymoman2682 4 года назад

is putting wire from charging plug actually putting any extra volts into the reciever , i did this mod and just removed the power cable from my ppm cable and just ran the wire to the charge plug on the single cell , therefore i can use low voltage alarm on my remote , so thats only putting up to 4volts into the reciever , not the 12.6 you are ,,, also the cut and wire mod from the resistor to the cut pin , what is that actually doing as i never did it that way... thanks

@HomeDronen 5 лет назад

I appreciate the info...cheers!

@kickfliph 2 года назад

Hello there, I'm trying to replicate the mod, so far I have made the cuts for the pin, in the front side, and in the back. But when I measure with the voltmeter I still have continuity, I scraped all that I believe makes the connection to the other pins in line but looks like It's still connected to the others. My board is like your brown color and not green as I see in some others videos posts, is that make any difference? I should do something else for this model/version board for the mod to work?

@hoath99 2 года назад

I think I have the same board as you, at the reverse of the pin, cut right into the corner on both the vertical & horizontal board. When i worked this out it cut continuity for me.

@jc_fpv_ec 4 года назад

function for 4s battery ???

@technoroid 4 года назад

Hello, do you know what is lowest voltage and highest can be monitored? I plan to use 6S LiPo and want to keep up with voltage monitoring, will it work? Thank you in advance

@TechIdeasAG 4 года назад

It's just simple, whatever battery you use just use 3s to the receiver, you can easily get it from your battery's charging connector. Hope you understand.

@finleeover 4 года назад

@@TechIdeasAG Thank you. I understand.

@SimjimX0 5 лет назад

Hello nice video How do you cut the wire to the rx fsia6b please?

@k1ortia 3 года назад

Just buy the £3 FS-CVT01 Sensor. plug and play in 5 seconds. job done

@DLM517 3 года назад

THANKS.

@DLM517 3 года назад

what country coinage is it as my keyboatd doesn't have it, thanks.

@jimstewart6720 2 года назад

Looks pretty risky......I bought the sensor!

@Infinitymotivation 5 лет назад

Amazing

@TechIdeasAG 5 лет назад

Thank you

@prabalsingh3622 5 лет назад

Nice Video 👌 But please make a video on monster amplifier... Can you make ?

@prajvalbs8787 3 года назад

Will this work for 4s , will it burn on 4s , please reply

@TechIdeasAG 3 года назад

It'll damage getting very hot

@prajvalbs8787 3 года назад

Ok tq

@prajvalbs8787 3 года назад

Can i use 3s

@melvi8834 3 года назад

the video is not very good as it does not show at all well where it needs to be cut. I managed to make this change which is not very simple and not for everyone. I repeat the video does not show at all well where to cut in the part below.

@DLM517 3 года назад

No comment!

@yashsoni7137 3 года назад

When i give it power a theer face black ic which placed between two yellow ic is heating too much