How To program DEI Directed ( Viper Python Avital Sidewinder Boa Valet and Hornet ) Alarm Remote Transmitter Fobs, Basically all Directed brand remote controls. To buy replacements come by our site at lesscosales.com
1998 dodge ram 2500 (manual trans.) with Python 1200XP/473P remote. Bought the truck used, key fobs had dead batteries. Replaced batteries and nothing. These instructions worked perfectly to program the new fobs. Just follow his instructions, pause the video as you go if you have to. Thank you for this video!
Thank you very much! With my Viper 7701, I had to use channels 2, 3, 4 and5; I still had to go through channel 1 with valet button part of process, but skipped step with actual remote. This saved me time, money and stress! Thanks a lot!
Thanks for making this tutorial. I had to replace my Avital transmitter and your video made much more sense than the directions. I just had to get channel 1 setup and it remembered all the other commands as well (since it was a replacement, not a new install).
@smallm86 same way as I show, on that one remote start will program automatically after you program channel one, typically you hold lock and unlock on that model to start the car
This is also valid for Python 7701 p/v/x, I just tried for Toyota Sienna 2009 and manage to do in first go.....Thanks Lessco Electronics.......you are the best
Hey, this worked for my AutoMate Remote start/Alarm combo! Thank you so much! I programmed a cheapo aftermarket transmitter from Ebay that was $17! WooHooo!
This worked excellent, I just did it on my car... I have a Viper alarm with replacement remote I472, I had a 2-way at first but they keep breaking i'm just going to stick to this basic one. The chirps worked a little different than at first it was 2 chirps for lock 3 chirps for unlock 1 chirp for Remote Start, and 4 chirps for AUX on this remote! Worked great though definitely a good video
Well done Exactly what i needed. i was sure my remote had just lost its sync with the alarm system. couple of minutes watching the video and a couple doing it and all is well!
does it work with the alarm but not with the factory switch? that tells you where the issue is coming from right there. iof the alarm does but not the cars switch the circuit is bad on the car side since the alarm throws its own 12v+ to the relays externally
Thanks for the compliment, The only 2 ways that work on that are the 479v, 479p and the clifford comp. That 7701 is totally different, different frequency and all unfortunately
So I have one of these 7701, the unlock button isn't working too well. Can I buy a 471 which only has 2 buttons to assist with the unlocking if it can be program to work with the 7701?
Hi! I just discovered my car previously had remote start. It was installed at least 15 years ago before we got it. Anyway I followed the antenna wire to the box. It's a DEI Valet model 552T. I obviously don't have a remote, and it doesn't have a valet switch. I jumped the terminals in the blue plug and got nothing... Did the installer disable it before they sold it?? Thanks a lot!!
for channel one you push the valet button once (and hold) thats the 1st channel you learned successfully, after hat hit the valet button 2x and hold it (you should hear 2 chirps for channel 2) then you learn ch2's button, same for 3 (but 3x) and 4 (but 4x). and ALL the remotes MUST be done at the same time, if you dont the old one will be deleted. Good luck
Hi, thanks for the help! My remote start now works for the first time since owning the vehicle (purchased used)! However, I must have done something wrong as the doors will not lock or unlock with the remote. Thoughts?
on non alarm type units, you dont need the door wire input, just do the programming minus that part. Do key on press valet button 1x then press and hold, then hit the transmitter to learn in the new code.
great video - if the device is a auto start and alarm combo; do you need to program the remote start function as well? or is it automatically programmed thanks
You need to program ch1 as lock, channel 2 as unlock, then 3 and 4 respectively, try that, if you still have trouble, try skipping programming ch2, Ive seen that work before as well.
hope i can figure this out with your help , i have the valet 551R worked great for 2 years with good range from inside my upstairs and i have seemed to lost Range of my remote , sometimes i need to be next to my truck , other times it will work from 20 feet away , i have changed new batterys twice and checked all connections and all are good , any ideas ?
Thanks for the video but I gotta quick question I have a busted Clifford sst 7701 remote and I want to program the new remote to my car. I currently have the 4 buttons, lock, unlock, a trunk button and a star button. I don't think the trunk button is programmed for my truck but the star button starts my car. When I go thru the process you showed do I still need to program the trunk button on channel 3? Or do I skip and program the star button?
Hello, just had to replace the brain on an avital 3100 in my 1996 tahoe that had been installed by a shop a few years back. I have got everything working but the rear hatch release. I have tried all options in the manual and it does not want to program for the hatch using the trunk button on the remote. What am I missing or doing wrong? This was working before. Any help would be greatly appreciated. Thank you!
Some system have the chirp feature ommited (or be so weak you have a hard time even hearing it), that may be all there is to it, Dont let it deter you, follow through with the programming just as I do it.
I can only seem to program the first channel onto my new remote, there isn't a 2nd chirp after finishing the first chirp. Also, do I need to reprogram my old remote? It still works, and I just want to add a new one so do i just follow your directions to add in the new remote.
For me, I have I think the viper 3500 alarm (the small grey and black remote) would it be the same, except instead of the aux it'd be Trunk, and instead of the startup, it'd be panic? (My buttons are Lock, Unlock, AUX, and a "*" which I'm guessing is panic. Would I do the same?
Hi I have a python 1400xp remote starter and the python 474p transmitter. Can I buy any other 1-way DEI transmitter to program to my 1400, or does it have to be the 474p transmitter? My transmitter shell broke and I would like to buy a more modern looking transmitter. Thanks for the vid!
I just ordered a new Viper 7701, to replace my Python 7701 as it has broken. I still don't get the chirps when I try to press once and hold down the Valet Button. Does the car door need to be opened ALL THE WAY?
I have a Viper 500 ESP installed and yes it's old i think i bought in 2001 but still works really good, i heard you say any remote can be programmed even the 2-way with LCD display, you think I'll be able to program one of the 2-way with LCD with my 500 ESP? please let me know I'll really appreciate it. Thank you.
How do you program it if you have a valet switch instead of a button? I bought two of your remotes that were the same exact thing as the old one that came with my vehicle and I am just having a hard time programming it with the switch instead of the button.
Hi sir, we boght a repo car and has DEI system. How do we purchase a matching remote with the car system? And the wires by the windshield is broke, does these wires has any significant to the remote? Thanks!
Not sure on system, but I have a viper 479v fob. It's blue and looks like a small phone, very common fob. It has always worked. I tried your method and got half way through. Got a chirp after holding valet and that was as far as I got. After I heard the chirp I pressed the lock button on the fob and did not get a tone confirming it read the fob. It has a remote start and alarm system to lock and unlock the vehicle.
Instead of hittting the valet once and holding after the first channel learns, try pressing the valet 2x then holding it, Ive done that a few times myself to get them going if theyre stubborn.
Hello, Great video I used 2 years ago! I bought a new replacement transmitter my 3rd or 4th and it didn't work. How can I delete all the remotes that are programmed so my new remote will work? Thanks
I have the one with lock and unlock as one button and then the trunk and remote start. So do i press the lock button for channel one and the again the same button for unlock for channel 2?
hey, just got done installing a viper 5706V however when i go to remote start it gets ready to start, accessory, ignition but it doesn't engage the starter and im getting 4 flash "Transmitter shutdown error" any advice? thank you
Hey there, thanks for that! I've tried to add a remote to my DEI SST (1 mile range), but it's not working. The alarm only came with one remote, and I'm trying to add a non lcd 4 button. Is this my problem?
Hello I have a dei 552t and want to upgrade to a 2 way lcd remote system, I like to find one that would be the same wiring as the 552t valet,.. Can you recommend one or two?? if there are any?? Please
Seems I can't get a new remote to pair with my crap viper 500. Have check with bit writer the system is unlocked but when I follow your instructions the alarm gives me a loins siren after a few seconds on step one can't get to step two. I do hear the chirp after one and one more then hold. Any suggestions? Thanks
Is there a way to reset all the settings on a Viper Remote alarm system? I have a 479V/P/C (model 791xv) and the previous owner of the vehicle never left me any information on how it was programmed. I believe the starter kill feature is enabled and I can never start the car with the key but only with the remote start feature on the remote.
I just purchased a vehicle that has the DEI 5X03 module, it’s missing the fob , do you know what fob it uses or can I use any DEI fob? Also where can I get the fob ? Great content btw, appreciate your reply...
I have a Sidewinder auto start. When trying to program a new remote, the lock button works to lock and unlock, none of the other buttons work. Is there a reset sequence to wipe the system? I’ve tried just restarting the sequence, but still only the lock button works.
Do I need the door locks grounded? I cant get my remote starter to program. I have no power locks. The LED on the module is not turning on. I have it grounded and also grounded the neutral saftey switch wire, but cannot seem to get it to work? Im not sure what im doing wrong any help is appreciated. THanks
Lessco I purchase additional remotes from you a while ago off of eBay for my 474v. I turned he key to the on position while the driver's side door was open and then pressed and released the valet button then press and held down the valet button until the audible chirps the only remote the system is acknowledging is my original remote not the new remotes while programming the lock button.
hi I have the viper 7142v alarm system,tge problem is I only had one remote,I ordered a spare but lost the one I was using,the cat is armed,can I still program in the new remote and b if so,what is the procedure?
i have a question but im not sure if you have the answer. I have a viper 791xv responder alarm with remote start. When i use my remote start my truck startsand idles for about 1minute and shuts off. Before i had this issue my truck would idle for about 10min. I would greatly appreciate it if you can walk me through fixing the problem . I have my owners manual but it doesnt have the programming for the issue . thanks
I have a Clifford CS3000 Smart Start system. I talked to shop into a remote for when I don't have cell signal. I want to add an additional remote. I have previous remote from a vehicle I don't have any more. Can I program 2 different style remotes to the same system?
I have a valet 552t that hooked up out side car so i can program the remote before install and the light just flashes when given power and wont stop or go in to program mod any idea why thanks.
You may need to go to channels higher than channel four. After playing around a bit (restarting the sequence over a few times) starting out with only the lock working using the panic button, I eventually got the channels to match the buttons. I skipped the first three channels and used channel 4 and 5... and then it worked (matched for lock and unlock.) I don't have an aux and the panic did work! Go figure.
Viper 160XV does not sound horn after pressing and holding the remote button on the control you want to teach. Valley bottom no horn after holding the button on second holed. Just light flashes once or twice or three times or four times. Please help.
hi im hoping you might be able to help me i have a hornet 564T alarm and i was using a 477T LCD remote it did work fine till i removed it from the car i wanted to check it was still working fine as it hadnt been fitted in a car for a month or so ..I have it hooked up like you have in the video but my 477T remote isnt showing it sending a signal out from the remote as it did from before from little transmitter symbol..is my remote naffed has it had it thanks in advance
great video, just replace my old transmitter a 479v, all I had to do was 1. open door 2.turn key to ON position 3.press valet switch once. let go, then press and hold till hear a chirp 3.while still holding ON the valet switch I press and released the lock Button on my transmitter then heard a beep on it, follow by chirps on the car 4. turn the key to the OFF switch position (and again follow by chirps) and that was it. all I had to press was one single button on my transmitter and it learn all the other ones by it self,(lock, unlock,trunk,remote start all with the respective buttons) cool huh!
Thanks you. Still not coding , It is matter if I have a 4 wires antenna receiver or 3 wires on the plug ? I have 4 wires . But I saw some have only 3 wire on the plug. Could 4 wires it for 2 way receiver (I took it from viper 791xv ).? I just cut the extra wire on the receiver plug still not coding. Any info be greatly appreciated.
Hi i have a replacement 2 way the 479v that apparently replaced the 489v , i tried this and its not working. Am i missing something or are there alternative ways? The dealer said that the 479v 2 way is compatible with the 489v so it should be no problem. SHOULD!
I tried following your instructions. After I pressed the valet button and released tqhen pressed and held till I heard the chirp, I let go and pressed the lock button on the remote but nothing happened. I called direct and the recording said to press trhe Valet, release, then press and hold. once I hear the chirp, I am to continue to hold the valet button in till after I press the remote button and get a confirmation sound.