How to Program Remote Control duplicator

Подписаться 8 тыс.

Просмотров 1,1 млн

50% 1

Newer version, more compatible ： • How to Program Remote ...
www.aliexpress.com/item/32678...
Link from DE: www.amazon.de/dp/B09GF789Q8
In the configuration and selling process, most clients wish to replace the original remote control with a general remote control, while such remote control has not be developed. You may configure your remote control within 2 seconds if you meet the following three conditions:
Condition I: the original remote control may be used normally
Condition II: frequency of original remote control is 433Mhz
Condition III: IC model of original remote control is 2262 2260 1527 2240 and compatible IC (rolling code remotes will not work)
Application method:
1.Clear the copy remote controller: Long press the above two keys at the same time and release your hand when the light flash quickly.
2.Copy: Press the button of the copyed remote control with one hand, and press the button of the new remote control with the other hand, keep for a few seconds
3.Use:If all the above operation succeed, the romote control can be used dirtectly. If it can not work, please operate again from Clearing
4.Recover: If you meet misoperation and cancle useful codes, before re-copy, you can press the below two keys at the same time for 2 seconds and release when the lights flash quickly, then the control will be recovered

Наука

Опубликовано:

7 сен 2016

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 149

@RomanVideos1 2 месяца назад

I did copy the signal but the gate still doesn't open...

@qiachip 2 месяца назад

I'm glad you asked the question, I hope I can help you First of all, you need to figure out whether the signals you copy are the same, because the signals have different frequencies, such as: 433,315; and the signals also have different formats, including 16-bit and 32-bit; the signals also have different ways of changing: For example, the ordinary 1527 has no change, but there is a rolling code that changes; You need to ensure that these are the same, i.e. you want to confirm; What frequency does your remote control have, what format is it, and is it a rolling code? Is your clone remote capable of replicating this type of remote? By solving the above questions, you will know what products you need to purchase; Now from the analysis of your words, you copied successfully, but you can't open the door. Based on our experience, we judge that your original remote control should have a rolling code, so although it can be copied, it cannot open the door. You need to replace it with one that can be copied. Copy remote control for rolling codes Hope the answer can help you Also looking forward to your follow-up feedback

@RomanVideos1 2 месяца назад

@@qiachip My remote is 433. i figured out that the gate accepts a different frequency so it doesn't recognize my remote. i've ordered a different one that can copy multiple range of frequencies. but thanks for the help.

@nunosilva513 10 месяцев назад

You really helped. I was not getting my remotes copyed untill I understood that they has to touch each other. Thanks !!!!!!

@supinac17 3 года назад

I found several stupid tutorials but yours is only usefull. Thanks

@victorko5671 Год назад

Wow, you just saved us time and money! Thank you!

@vbp6159 10 месяцев назад

Only the text with explanation was alittle fast but the info from this video was very usefull. thank you sir.

@lebeyes 3 года назад

This works perfectly with the Hörmann HSM4-868

@slovenec88 7 лет назад

Thank you! It works on a generic one, just remember to put antennas together.

@qiachip 6 лет назад

Oh, thank you so much for your advice.

@user-ij3hp1km6g 5 месяцев назад

I don’t know for you guys but for me it works perfectly and with two different types!! Thanks for the informations Sir!! You saved me 60€!!

@Arneby 4 года назад

After watching this it's easier to understand why so man parts of the world just don't work. Imagine this guy being in charge of just about anything.

@brettsalter3300 2 года назад

Agreed, Unclear which buttons are pressed, their thumbs obscure any accurate demonstration.Terrible, and frustrating.

@TJBiker1200 4 года назад

Thank you!

@rodi9876543211234567 7 лет назад

thank's, your video is complete!

@alwave 4 года назад

Please do not buy but if you are watching this its too late. It does not work. You can keep looking at all the videos you want, it simply does not work.

@vebez5993 3 года назад

It’s because you have a different model genius

@1988nProud 10 дней назад

Lmao before buying did u open the remote to figure out chip hz? Also this only works for "dumb" or lowtech pairs that well remain static.

@miftachulhuda6341 4 года назад

I have remote nd both have same code how i can get another code without cloning another remote?

@olsitafaj3571 4 года назад

Thank bro😀

@letechnochat 3 года назад

thx for your video

@paricutin149 Год назад

Thank You!

@hayatinicindentv7133 4 года назад

Thank you

@bluebirdsalive5995 3 года назад

Thank you very much, perfect video just the core things short and clean, thank you!

@DavidRamirez-be1ke 2 года назад

Did you have to hit the learn button to program it?

@qiachip 2 года назад

Hello, there is no need to learn the button, just copy the code of the remote control

@2007spiderman2007 7 лет назад

In your example you need to hold A and B until leds flash twice, then while still holding down A pres butt B three times on the third press the leds will flash rapidly you can then let go of button A, This will clear the codes. In your example after you thought that you cleared the codes you can still see the leds on B, C and D light when you press the button !

@qiachip 7 лет назад

The LED flash only indicates that the receiver receives the signal.

@sheikdawood7124 5 лет назад

Hi sir please contact number sent me my no 9884231246

@mariaduran6139 4 года назад

But the lught is still Blue

@ninomb1137 Год назад

Thanks this work for mine

@NexaTube Год назад

That's right.

@user-gx8id1tq6d Год назад

Is this true for all remote controllers of this size?

@Ioan_C Год назад

thanks a lot!!!

@ahmadzahidi3552 Год назад

thank you it works

@sarai7512 11 месяцев назад

Everything done exactly like the video but the door didn’t open . Note: when im doing the copy process when I press and hold the old key remote the garage opens I think this wrong. AND Same frequency 433mhz please can you help

@amitvalecha1792 Год назад

Can it be used as remote for my car central locking

@dimchegcom 2 года назад

Thank you, mate! You literally saved me 40€

@hadjikorbi1652 Год назад

@WRAND2208 5 месяцев назад

It works man!

@Vlad_in_the_Dale 3 года назад

Thanks a lot, helped me with this little monster!

@DavidRamirez-be1ke 2 года назад

Did you have to hit the learn button to complete the programming?

@Vlad_in_the_Dale 2 года назад

@@DavidRamirez-be1ke No, not really.

@genin69 4 года назад

ok 1:44 so smash them together works!

@qrsimon 3 года назад

Hulk smash

@charlie58ize 2 года назад

My remote has only A B C and it’s stopped working but light coming on. Cannot pair with door

@lifeisstr4nge 7 лет назад

What should i try if resetting worked, copying worked but the boom barrier only accepts the code once? Then my copy does not work again.

@MoAli72 Год назад

Sounds like you need a 'rolling code' remote.

@randolphsnyder1505 11 месяцев назад

I did the cloning of original fob,orig fob has 3 functions open,stop and close ,all on same button.cloned fob only opens,no stop or close.Any ideas ?

@wilberthiebert5075 4 месяца назад

I had the same problem with the same remote. I have to cloning open in A button and close in B button. If open with A it stop with B and close again with A. It's because it's a rolling code. With other remote I had no problem.

@Tommy-gm7uo 3 года назад

Will this work if the original fob is not the same brand and model?

@qiachip 2 года назад

You can try

@tif974 Год назад

When reseting codes. What did you do different between the correct and the wrong way ?

@jonosmani9364 3 месяца назад

In the correct one he let the first button go after 1s

@tif974 3 месяца назад

@@jonosmani9364 thanks !

@baobaolovely 3 года назад

I've done it right but it doesn't work I can't open the gate. Can you help me?

@user-qg4sn5tn7l Год назад

315mhz or 433mhz?

@kuhne 4 года назад

Hi. I bought 11 of these. It’s exactly the same as this one but the light is blue. I tried resetting every single one and the reset works but when I try to clone the remote it never learns the old remote. I tried with all 11 of them and none works. I tried with 3 different garage remotes and two tv remotes and it never learns the code.

@richarda4115 4 года назад

Put them very close together and hold the button on the duplicator and hold it on the original

@sweatvallyhigh 5 лет назад

What battery does this remote use? I got one from from Wish with no battery or instructions.

@qiachip 5 лет назад

sweatvallyhigh can you send us the link where you purchased your remote control from?

@qiachip 5 лет назад

Since most of the remote control just have the same outlook but most of them are not using the same battery, the battery we are using on the video are lithium CR2032. Even copy code remote control uses various battery.

@sweatvallyhigh 5 лет назад

Best I can tell a 3V button cell the size of a US nickel but 1.5 times the thickness would work. I need to head to the store, but it's 20 below right now.

@qiachip 5 лет назад

sweatvallyhigh the following link you’ve sent us isn’t one of our product. And we do not have an identical product for it, so I don’t really have a clue. I think the best way is to just ask the seller which battery they are using.

@shantecarroll9783 5 лет назад

27a

@Z19901000sadd4m 20 дней назад

can I add a third remote without effecting any of the other two for a garage opener

@qiachip 18 дней назад

I'm glad you asked the question. From your question, I can understand your concerns about duplicating the remote control. I'll answer your question first, and then I'll explain the principle. You can add a third remote control without affecting any of your previous remote controls. The reason is that the duplicat remote control copies the code value of your garage door remote control, and then they can both transmit the same signal, without any interference to the original garage door remote control. After they are copied, they can be used as independent remote controls! However, there is a more complex rolling code remote control that is a little different, because the code value of each signal they transmit will change, which requires specific analysis! I hope to solve your doubts and look forward to your follow-up feedback!

@AhmetElhann 9 месяцев назад

I did everything accordingly, yet after copying, when I press the button it doesnt flash at all like the copying is not successfull.

@sunflower6434 3 года назад

Does it have to EXACTLY the same type of remote???

@qiachip 2 года назад

At least the same working frequency

@hantozoli Год назад

Reset and copy looks successful and it works fine for the very first time when I first press the button, but then it "forgets" the code and never works again unless I repeat the whole procedure. Any idea?

@anamemeteau1857 6 месяцев назад

I have the same issue!!!

@wilberthiebert5075 4 месяца назад

Your remote ist rolling code, so you must buy other remote that can clone it.

@fabianm2980 6 лет назад

Reseteo el mando y borro todas las señales. Luego intento clonar el original. Funciona el mando durante 5 segundos luego deja de funcionar. ¿Saben por que?

@qiachip 6 лет назад

Hello, we assumed you did not have a entire procedure of cloning. First press the key fob earlier than the original remote.

@obi_Vision Год назад

Not working on ACM EAGLE TX2 ,only working one time and no more working.....WHY

@offroader22 5 лет назад

When resetting; what's the difference between the way you did it wrong and the way you did it correct?

@qiachip 5 лет назад

Hi Espen Loken, The correct way is to put 2 remote control really close in order to get in range when you are trying to copy a key. The remote control won't be able to copy each other if the distance is too far away. It is better to stick 2 remote controls side by side in order to make a successful code copy.

@offroader22 5 лет назад

@@qiachip yes. But I can't see the difference between the right and the wrong way to clear the code

@taewonhwang3181 5 лет назад

there looks no difference of course

@Omarshoukry2012 5 лет назад

Sorry, but i think i understood the question differently. i though it mentioned while resetting not while cloning. i have the same problem when i try to rest its always appears as its mentioned wrong and never been correct! .. the main concern here is what excatly is the reason behind WRONG and CORRECT and how we can make it CORRECT!?.. i will appreciate ur answer

@ozgurteyhani4527 6 лет назад

is there any way to clear only one button?

@qiachip 6 лет назад

Hi, when you clear code, all the button's code would be erased.

@yyyyyc 6 лет назад

Hi, I have the same look alike remote control, with Blue led. I cannot reset it. I cannot get the led to blink, not when I push A and B together for several seconds, not when I push C and D together for several seconds, and not when I push a single button for a long time. Is there a possibility the remote is blocked for programming? Thank you

@qiachip 6 лет назад

Hi, first you need to change battery and make sure it works. Second, you could try this step: Press B and D together. If the second method doesn't work, try to clone your original remote to see if there is light.

@yyyyyc 6 лет назад

Hi. Thanks for your reply, Well, The battery is fine. I tried the B and D combination. It does not work. (also A and C combination). I'm afraid I did not understand what you mean by "try to clone your original remote to see if there is light"

@qiachip 6 лет назад

As you could see in the video 1:42, the remote blink when you program them with the original remote. It was because the duplicator receives signal from your original remote, so it blinks.

@sergiotomas1191 3 года назад

same problem here and have tried all.

@Sdaniels3152 3 года назад

Did you get to clear the memory? I am trying with a Blue led remote too.

@virgiliofi Год назад

Hi! I have the blue led light remote. Once I programmed the new remote, it looses the coding after a couple of minutes. What can I do? Please help!🙏

@andrelaishong577 6 месяцев назад

Hi, did you find a fix im having the same issue,thanks

@virgiliofi 6 месяцев назад

@@andrelaishong577 Hi Andre! No, I ended up buying a new one 😔

@wilberthiebert5075 4 месяца назад

These remote can't clone properly a rolling code. Or clone one time in A button and B button, A to open and close and B to stop.

@randolphsnyder1505 11 месяцев назад

Managed to copy,however the cloned fob will only do 1 function ,open gate only,no stop or close.Any ideas ?

@sarai7512 11 месяцев назад

Mine isn’t doing any

@wilberthiebert5075 4 месяца назад

@zeuline1 Год назад

I did all the same. Reset, clone. Lights the same blink, after clone steady on on press, but remote doing nothing. On old remote the same MHZ 433,92. Where can be trick?

@sarai7512 11 месяцев назад

Same

@reviewbangroy1858 4 года назад

Buat remote mobil vios gmn caranya

@karlas2546 14 дней назад

I have the blue control as a copy and I do all these steps and it seems to be ready but it doesn't work

@qiachip 13 дней назад

I am glad to answer your question. Because different manufacturers may have different settings, the operation of the video is for our brand of products. Next, in response to your question, we need to clarify what the failure phenomenon is. This way, we can distinguish the specific problem. For example, if the remote control is copied successfully, but the receiver cannot be operated, it is very likely that the previous remote control has a rolling code, and the copied remote control cannot copy the rolling code, which leads to this problem. I hope to receive your feedback, confirm the brand of the product you purchased, and then describe a more specific phenomenon, hoping to help you solve the problem.

@ilhanozgan 4 года назад

Not working with my Honda minivan remote,junk

@javyqv 3 года назад

I bought a remote just like that but i am unable to place it in learning mode even if i let the 2 top bottoms hold at the same time it wont work any sugestion

@bharathchand4154 3 года назад

Same here. Just doesn’t work

@peterh1875 4 года назад

never get to blinking on my remote

@peterbroad1772 3 года назад

Same here. Press A and B together and hold and the LED is on and it never blinks or resets. Garbage.

@Gr8Talk 3 года назад

Done this over and over - no result. Am guessing the supplier knows this and don't care?

@sinergija1236589 4 года назад

When I press both bottons A and B together light is always on no matter how long I'm pressing together. Light is always on, without flickering as much as I'm pressing bottons. Please how can I clear the memory and program my remote? Thanks

@tamkepa 3 года назад

Did you find a fix? I have the same issue

@ChrisEscape 3 года назад

@@tamkepa Did you? same problem

@wattage2007 2 года назад

@@ChrisEscape I've seen other models of these on which you need do the A and B button press but release the B button while keeping the A pressed. Then, with the A button still pressed, 3 slow presses of B again then that's it cleared. I just find it incredible they make these amazing products then absolutely fail to explain how they work.

@Wen-hz9mb Год назад

Why won’t mine clear ???

@davidteixeira7390 Год назад

Can I erase only C and D anda then reprogram? I can't loose A and B?

@wilberthiebert5075 4 месяца назад

I will erase all button.

@Lohtia25 3 года назад

Copying not working tried lot of times

@gonzaloperal5512 Год назад

I resetted my new remote and copied the old one. Then copied the button on A,B and C. The garage responded to each button once and then they never worked again.

@Sorjen108 Год назад

I got the same issue, did you find any fixes?

@MoAli72 Год назад

@@Sorjen108 Sounds like a 'rolling code' remote is what you need. This tech basically sends a new code in transmission each time to prevent attackers cloning the transmission.

@Sorjen108 Год назад

@@MoAli72 Yes I think so, do you know where can I get a rolling code remote please?

@zulfikranzulmos4066 3 года назад

Why u show wrong 😅😅

@carlenebourke7736 7 лет назад

I have tried what you suggested but my remotes still won't reset. HELP!!!!

@nateepongteerarat8013 6 лет назад

Carlene Bourke me too!!!!!!!!!!

@ericmccormack8678 6 лет назад

Don't work

@thepharaoh2832 5 лет назад

Me too, non of that works

@neilcvernon6957 2 года назад

Ant get mine to Flash to reset :(

@nik0las1 3 года назад

Mine is not cleaning.

@marcfonteyn1434 Месяц назад

Sorry but is not working with me !!! I followed all te steps but at the end therse is NO ligth annymore ???

@qiachip Месяц назад

I need to confirm: Can your cloned remote control copy another remote control? If not Then you need to understand a few questions: 1. Can the frequency of the copied remote control copy another universal remote control? 2. Are their encoding formats the same, such as EV1527 or PT2262, etc. 3. Is the ordinary remote control or the copied remote control in encrypted rolling code mode? Finally If you buy from us, you can send a picture of your remote control to customer service We can help you confirm the above questions through the picture! Hope it helps you

@MoAli72 Год назад

It's quite shit we have to reset the whole remote every time we want to clone a button or something.

@eusebiolucas1017 Год назад

Programarlo

@davidr.montgomery8919 5 лет назад

I don't have a way of making a video. I followed your directions carefully. Well, you have your money. Thanks for nothing. I just want my money back. No wonder you say all sales are final.

@qiachip 5 лет назад

Can you tell me what went wrong with the product? May be I can fix it for you according to your description.

@sarai7512 11 месяцев назад

@@qiachip hello, mine as well didn’t work ( the door DIDNT open) The reset and copy code was done correctly but at the end the remote didn’t did it job. Please help whats the problem

@zulfikranzulmos4066 3 года назад

Haha why would u need to show wrong way and correct way.. Just show correct way simple 😅😅

@davidr.montgomery8919 5 лет назад

Personally I believe this is a scam and a farce. While I can get this to clear, I cannot get it to set up the remote for ANY key. I am a retired computer programmer and I know computers very well. I am just before going to Better Business Bureau and lodging a complaint. I don't need no bunch of baloney. I need to know how this works and why it won't.

@qiachip 5 лет назад

The copy remote control only works with a few type of code, can you make a video of what you did? Thx.