Appreciate how you took the time for one of your subscribers and helped him with his small project. I am glad to see that no job is to small. As a contractor myself, this was and is some of the best advice a have gotten. We all started out small and that is something to remember. Thank you Sir. Well done.
We never touched anything house -ey a day in our lives and we just installed ours after getting the old one and frame out. I rented a sawzall and used that and DIDNT lose any limbs. Between this and the other video, I was able to do it. Thanks so much man
Fantastic video. You give very precise instructions without any extra chatter. You show each step very clearly and explain the reasons why. You definitely boosted my confidence so that I feel good about trying this myself. You just found yourself a new subscriber.
This is the first video of yours I have seen and I have to extend my gratitude with this comment. There are a number of reasons I'm now a follower one being your speed within the process even the youngest of beginners should be able to follow your basic yet thorough video and amongst other reasons again Thank You for posting
This was extremely helpful... im a new home owner and wanted to replace my sliding doors... i like to see the procedure but ill keep paying you professionals
Just did a patio door last fall, this video would have saved me some time! Too bad you aren’t in the Wisconsin area, I would have plenty of content to film lol!
I use to install doors for Home Depot. So I have installed hundreds of patio doors. We did several Anderson doors. I am far away from the Wisconsin area where I can take you up on that lol. Thanks for watching!
Absolutely love your technique. Checking everything first and having a home owner to allow to take the trim off makes the replacement go smoothly. Love the new look and as always, Great job Josh. 👍🏻
I was tearing up a floor today and was talking about how I hate liquid nail and then I watch your videos for the first time and never seen anyone use as much as you lol
Thanks a lot Noah! My wife is still debating about tile color so it might be a couple weekends until I put out that video. I hope your projects are going well!
Hey Josh, nice video and just in time ! I’m replacing two sliding patio doors at this time. I had a severe water intrusion at the bottom of both because of a deck installed when the house was new 17 years ago! The flashing under the ledger board was not a z type and the never nailed it above the ledger to the wall or chalked it or sealed it at all! I had to replace 20 + ft of my rim joist and damage to the floor under the sliders. This wall faces the West and is always in receiving the full force of any rain here in NC . It so happens I’m using Relia Built slider’s 👍👍 this is the second time I’ve ever replaced a patio door in 2 years. I just finished a remodel for my girlfriend house in 2020.
I usually use a tripod when making my videos and I do not have a camera person. This was her second time recording a video for me and she did do great! I will let her know about your awesome comment. Thanks a lot for watching!
I truly need to replace my back sliding door. The house was built in 1968 and it's the original door. I've replaced the rollers so many times and can't even buy them any more. The aluminum threshold is worn almost flat and and the screws in the handle stripped out so I am using screwdrivers to open it and vice grips to lock it. So of course I'm watching videos. I'm waiting for fall when the bugs die out. Thanks for the video. Mine is brick but every little bit of info helps.
So at 11:02 you show how to set the reveal and adjust the latch. From the inside view we can see the holes to the latching side nailing flange are missing the opening. Did you install the piece of ? quarter ? board to fill that gap then somehow attach to that? Or is the latching side only fastened by two small latch screws?
How is the door secured to the home ? Just by the nailing flange & 2 screws used for the latch ? Are there any holes around the inside of the frame for install ?
Thank you for doing this video. My son just purchased a new patio door and it has the flanges on it. Now I know what I will need to do to the trim. The part I will have to do is make the opening to fit. He found a 72 in door in stock and his opening is 76 inches.
This is awesome! I just bought an older house with an opening door. I want a patio sliding door for summer for the screen door. Plus there's tips of things that could happen like the top gap of the patio in this video.
installing new sliding doors is always good, but I want to share with you my experience, I live in Orlando Florida, I contacted the Masterslide company with the problem of my sliding doors (if you ask, I will share the contacts) they replaced the rollers, installed a track cover and a new handle with a lock. Now my door is like new and I'm as happy as a child! And most importantly, I thought that I saved more than two thousand dollars! Just because repairs are cheaper!))) so think before ordering new ones. This is not advertising, this is my case.
Loved this video as the French Door you removed is the exact one we want to replace. Question, can you convert this French door (the one you removed) into a single door using the door from the French door you removed?
Thanks for the video. Very informative. Wouldn't it have been a good idea to apply some caulk behind the nailing flange before setting it into place? Any reason not to do that? Also it seems like some kind of flashing at the top would be good, although it looks like there is a nice overhang at this place.
I am going to replace double exterior doors with 72x80 replacement pre-hung product from JELD-WEN. I will be doing the work myself. Can the new doors be removed from the new frame, install the new frame, and reinstall the new doors into the new frame to make the job easier?
Dang, I watched this video specifically for the end and then you didn't do the part I was looking for. :/ My sliding glass door is fine, but the people who installed it just did not give two single craps about finishing up the job. It looks basically how this one in the video does by the end, only even less filled in with the foam. So I need to learn how to finish it up and make it not look so terrible.
It looks like my door has the flange that goes behind the vinyl siding. The door is 20 years old, and I think they just nailed it to the side of the house back then. Can you just drill a hole through the flange and then take your saws all and slice the flange off?
@The Excellent Laborer, at about the 12 minute mark I noticed you started talking about how to install the trim boards on the in and outside of the door. Do you have any videos or info you can share with me on how to do that? You said you'd show us how but you didn't have material. I am wanting to install a sliding patio door where I currently have French doors and the opening is slightly too big right now and so the opening needs to be shrunk a little bit and then new trim would have to go on after that. I've never done a project like this before, but it also doesn't seem like a terribly hard job. The outside of my house also has stucco on it since I'm here in AZ. Any help with this would be appreciated!
hello Josh. I did the reverse. I removed the sliding doors and I'm adding French doors. I' stuck after removing the sliding doors. How do I remove the aluminum frame that held the sliding doors? Thanks.
I don’t know your exact situation, but I do know from past experiences a sawzall is a big help in that situation. We would either sawzall the nailing flange and pull the frame out or sawsall down the middle of the frame then pull it out. I hope that helps!
I watched 2 of your slider installs. Just wanting to clarify the different schools of thought. Not challenging your technique. I had seen the question asked by another viewer and didn't see an answer so I thought Id take a shot. He had asked and Im also wondering. Regarding nailing the top flange. He had said he thought you don't. Other installers claim they dont due to changes in load, movement of header, expansion and contraction etc. potentially putting lift or flex on frame or worse, glass. They say they never nail top (Or bottom if applicable) only silicone or liquid nails and then nail sides. Allowing for some freedom of movement while still being sealed. What are your thoughts ? Aside from potential warranty issues.
Would you be able to reuse the door you take out in another opening? I am having French doors installed but would like to reuse my sliding doors they remove for another opening that currently has a sliding door. The sliding doors I want to replace frost up in the winter but the sliding doors that the French doors are replacing don't frost up.
All in all and educational video. In my opinion, never set a door with Liquid Nails, use 100% silicone and regardless of what you are setting it on. And I always flash the sill and tape the jambs for moisture and insect prevention. Better quality doors aren't as flimsy and don't need a rip to pad out to the inside trim. Seeing how bowed and easy you moved the latch side jamb was concerning to me...
I’ve installed hundreds of patio doors and always used at least a 4foot level . And as far as that great stuff I’ve always stayed away from it because it absorbs moisture. I use fiberglass insulation . But that’s just how I do it
This is a great video, but you lost me on the ending with the inch and a quarter wood that you had to add but didn't have the parts to show. Did you end up making a video on this part? I could't find it. you mentioned putting 5 quarter board on the outside, but I'm lost on how to do it.
I do not have a door frame to put my sliding door in. My problem is how to build that opening. All I have is an empty newly constructed 88"=H, 72"=W opening in my Sunroom Wall for a 79.5"H 70.75"W Door.
Just another viewer here. A proper install is typically with the slider on or toward the inside. So for example but not the reason, you can put a stick in the bottom track to offer additional security. I use that example to clarify what I meant by slider on the inside. Many doors can be configured by flipping and reinstalling hardware etc to accommodate this. Some allow flipping. Some allow taking the top and bottom rail off and switching. But keep in mind not all. Some you just have to buy or order correctly. When they specify LH or RH as an option to select its likely not a universal or reversible door. Universal or reversible are key buzz words to look for if you're having trouble finding the proper configuration for your needs.
How high should a threshold sit from the interior floor to the top of the frame? I recently had mine replaced and we keep catching ourselves from trimming over it as the previous one set fairly flush with the ground. Wood subfloor was replaced on outside due to rot as you mentioned but I’m wondering if it should have not been as thick due to the threshold being higher on new door vs old door.
How would you address it if it weren't level? I've seen some folks use shims but that wouldn't work great with your liquid nails. I suspect my old house would not go as easily as this one went for you 😂
It does hold the threshold down better than caulking. It also keeps the threshold more stable over time. I recommend liquid nails but silicone caulking is probably OK. Hope that helps!
Great video! I recently purchased a used patio/French door that I would like to install in my mobile home. My concern is that the house is 2'x4' construction while the door is 2'x6' framing. Is this doable?
No. I don't want to install a sliding patio door. I am getting replacement panels from a warranty claim and I want to replace and keep the frame that is there.
