No video :(

How To Remove Bearing Race From Hub (Andy’s Garage: Episode - 183)

Подписаться 78 тыс.

Просмотров 126 тыс.

0% 0

Andy Phillips shows how to remove a stuck bearing race from the hub shaft in just a few minutes. In many case when pulling a hub, the inner bearing race can get stuck to the hub shaft and break apart.
Below are links to other videos of mine that may be useful:
How To Remove A Bearing Race From Hub: • How To Remove Bearing ...
Pressing Wheel Bearings & Hubs: • How To Press Wheel Bea...
How To Remove A Bearing Retainer Ring: • How To Remove A Bearin...
How To Release A Stuck Shifter: • How To Release A Stuck...
How To Change Your Own Brakes: • How To Change Your Own...
How To Replace A Brake Booster: • Brake Booster Replacem...
How To Patch An Inner Tube: • How To Patch An Inner ...
How To Fix A Faulty Spare Tire Mechanism: • How To Fix Spare Tire ...
How To Check & Fill Battery Water Levels: • How To Check & Properl...
How To Charge A Car Battery: • How To Charge A Car Ba...
Quieting Noisy Lifters: • How To Quiet Noisy Lif...
How To Diagnose Suspension Noise: • How To Diagnose Suspen...
How To Find Cause Of Engine Noise: • How To Find The Cause ...
Removing Hubs With Hub Puller: • How To Easily Remove H...
How To Release A Stuck Shifter: • How To Release A Stuck...
How To Restore A Shifter Knob: • How To Restore A Shift...
Transmission Locked in "Park" & Key Cylinder Locked? - FIXED!!! • Transmission Locked in...
How To Check Transmission Fluid: • How To Check Transmiss...
Damaged Transmission Cooler Line Repair: • How To Fix Damaged Tra...
How To Repair Transmission Lines: • How To Repair Damaged ...
How To Install A Starter Switch: • How To Install A Start...
How To Change A Flat Tire: • How To Change A Flat T...
When To Change Your Tires: • When To Change Your Ti...
Diagnosis And Repair Of A Dead Car: • Car Won't Start? - Dia...
How To Test An Alternator: • How To Test An Alterna...
How To Charge A Car Battery: • How To Charge A Car Ba...
Testing Fuses: • How To Test Fuses (And...
Checking Battery Water Levels: • How To Check & Properl...
DISCLAIMER:
The individual featured on the Phillips Vision RU-vid Channel identified as Andrew Phillips, also known as Andy Phillips is not a professional mechanic, contractor or certified repairman. He does not have any formal training in the automotive field, or any other trade. He is strictly a Do It Yourself handyman.
Phillips Vision, or the individuals featured on this channel, assume no liability for anything you choose to do to your vehicles, appliances, games or any other items featured in the videos before, or after watching one of the videos or utilizing the content from this channel.
All Do it Yourself (DIY) repairs or modifications you perform are at your own risk. Proper safety precautions are always needed, and are the responsibility of the viewer to follow. In some cases, even if you perform everything properly, you can destroy or damage one or more things you are working on resulting is costly repairs.
In addition, if for some reason, the instructions on this channel are incorrect, resulting it something becoming damaged, Phillips Vision and those featured on this channel WILL NOT reimburse or pay in any way the costs that may be incurred due to following wrong instructions.
PLEASE DO NOT PERFORM ANYTHING SHOWN ON THIS CHANNEL (PHILLIPS VISION) UNLESS YOU FEEL COMFORTABLE AND CONFIDENT TO DO SO.

Опубликовано:

21 апр 2020

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 61

@raymondjackson6069 10 месяцев назад

Great video. Direct to the point. You can tell front he very start, he was serious, the procedure, involved and he did not waste time!

@Ratlins9 2 года назад

Definitely a top notch video, your camerawork including closeups and detailed instruction made for an excellent solution to a common problem. Great job!

@PhillipsVision 2 года назад

Thanks for the feedback; glad it helped👍

@pontiacsrule8761 2 года назад

Thanks so much. I knew how to use the tool but I couldn't think of what to use to push off. The socket with a bolt in the center is pure genius.

@jbr3rd 3 года назад

What I liked best was just the idea of for using a old rotor as a stabilization platform for while getting the race off the hub! Thanks Phillips Vision!

@alfredchow2677 3 года назад

Best extraction so far seen..

@grundyisland 3 года назад

This saved my bacon today! I ran out and bought that set right after I watched this vid. I used a round bar end cut-off as a spacer for the first pull, then a socket between the cut-off and the hub.

@PhillipsVision 3 года назад

Michael Grundy 👍

@radius4914 Год назад

probably best to keep the hub for the new bearing if its in good condition, so good to know!

@nicolasrestrepo838 10 месяцев назад

Excelente trabajo...lo felicito... muchas gracias por enseñar MUY bien a los que no sabemos nada...... MUY agradecido..es usted un genio..

@babyfacedassasin4418 2 года назад

Very concise video.

@Galaxie00 Месяц назад

Nice video. Don't forget to grease the threads on the centre load screw.

@tothepointvids5192 3 года назад

You are awesome!!!

@likits1999 3 года назад

This is the best system Ive seen. Thanks for the schooling. Im gonna be doing this to my sons BMW E60 tomorrow morning. You get genius point from me my friend. The moment I saw the hub on the rotor, I was amazed at your idea since I dont have a bench press or a hydraulic wheel bearing press. Great job!!!

@PhillipsVision 3 года назад

likits1999 thanks for the feedback. I’m glad the video helped. Good luck tomorrow 👍

@WrathL 2 года назад

@@PhillipsVision what about when it’s on can I use the same technic???

@PhillipsVision 2 года назад

@@WrathL it should work

@WrathL 2 года назад

@@PhillipsVision ok cool

@luistorres7047 Год назад

Great video.

@IndianTruckWorkshop 3 года назад

Great work buddy 👍👍

@PhillipsVision 3 года назад

Thanks man 👍

@SuperMapupa 2 года назад

always very well lubricate screw which applies pressure, makes life easier and prolongs screw's life...

@torreypines7337 2 года назад

Pretty awesome

@AidanRyan458 4 года назад

Good vid

@dannysautorepair 3 года назад

Great video sir thank you

@PhillipsVision 3 года назад

👍

@iAmIronMan0605 Год назад

I would have sold my soul to get the racer out I was working with. I finally gave in, and bought a hand sledge and chisel. It was out in 2 minutes after working for hours on it for days

@saffron1977 5 месяцев назад

Thank you

@thuglifemiklo7695 3 года назад

Great helpful video. Time to hrad to Harbor Freight my 2nd home haha.

@PhillipsVision 3 года назад

Thanks, I head there often

@sivucit 10 месяцев назад

i have honda pilot 2005 i tried this, but seems like the 5 ton bearing puller doesnt have enough width to go over the race..

@rickhoffman7656 3 года назад

thanks a lot, your video saved me!!

@PhillipsVision 3 года назад

Great, glad it helped

@louielou8262 10 месяцев назад

Thank you! Great video. Can I re use the race bearing again if it's not damaged???

@PhillipsVision 10 месяцев назад

I would not, just replace it with new

@louielou8262 10 месяцев назад

@@PhillipsVision is this part of the wheel bearing or are these 2 different parts?

@PhillipsVision 10 месяцев назад

@@louielou8262 it’s the inner part of the bearing

@louielou8262 10 месяцев назад

@@PhillipsVision thank you Sir 🙏🏼 I bought new wheel bearings 😁

@kunalauto2109 3 года назад

can you please share the link I want to purchase this tool

@PhillipsVision 3 года назад

It’s at Harbor Freight ... $49.99. www.harborfreight.com/bearing-separator-and-puller-set-62593.html

@jackslater230011 Год назад

Can you use this to remove the wheel hub as well?

@PhillipsVision Год назад

No, you will need a hub puller. Here’s a video I did showing how to use one ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-7BmiCGuNfA8.html

@cameroncooper4291 2 года назад

Hi have you ever removed a hub with a sealed bearing that was OK , left the cage on the hub and reinstalled the bearing .....or should you replace it ?

@PhillipsVision 2 года назад

Sealed bearings are easy to replace as one part so I always replace the entire piece

@PhillipsVision 2 года назад

Sealed bearings are easy to replace as one part so I always replace the entire piece

@PhillipsVision 2 года назад

Sealed bearings are easy to replace as one part so I always replace the entire piece

@athethiletshula6298 Год назад

It's so good, but it takes more time

@obsidiannightwolfe13 2 года назад

Unfortunately won't work on some cars that have an abs ring behind the hub.

@st6795 4 месяца назад

Would not work for my project to day with changing races out on a LippertComponents hub for camper. No edge to tap on and had to pay a machine shop to do the outer race. $115.00.

@llama9274 3 месяца назад

fudge i am dremeling mine vs that i love the dremel... old one got stolen oh well time for new

@vietcong4u 2 года назад

Great Vid but the method will not work on Honda bearing Race....

@kdeh21803 Год назад

I don't know how you get this to work..... It looks so easy here.... I've used this separator time after time and I can never get it to work..... the puller aways pulls off the race and I can never get it to work.............. then usually have to resort to a grinder or dremmel tool.

@kgarz76 2 года назад

What if the other piece is stuck on a spindle

@PhillipsVision 2 года назад

Did you use a hub puller?

@baverdi Год назад

Just score it with a grinder and hit it with a cold chisel. Cracks every time

@SUPRAP2 Год назад

Dude you're my hero!! I just did what you said and it worked. Slid right off the hub. Unbelievable.

@waynecook3 2 года назад

If you were doing this at home and had plenty of time I guess this is fine. In a workshop you would generally just cut a few slots in the race with a grinder and chisel it till it cracks. After that it will come off pretty easy

@Reaperofwind Год назад

Race separator is almost to small/ I need a bigger one.

@ocmacman17 3 года назад

if your race is a larger diameter than this you are still screwed. I bought this and my porsche race was more than the diameter on the larger tool. The bolts wouldn't even come out the other side. Maybe there is a larger model.

@imadog131 3 года назад

Lot of work for a 5 minute job with a chisel

@TSimms7 4 месяца назад

Yes, I believe I zipcut as much as I could at an angle, but was probably unnecessary. I then put a small notch in a chisel to catch the lip, and tap tap tap. Works fine on a clean shaft.