How to Remove GY6 Kickstarter Gear, Stroker, Woodruff Keys, Oil Seal on 157QMJ

Подписаться 10 тыс.

Просмотров 62 тыс.

50% 1

Thank you for watching and supporting my channel feel free to use my referral links. If you need help with any of these products call or text me Mike (209) 355-8088. I usually respond within 24 hrs.
--------------------------DO IT YOURSELF--------------------------
Time Required: 60-120mins.
Skill Level: Advance
Chemical Used:
• Bel-Ray Oil Exl Mineral 4T 10W-40 amzn.to/2TPO6dZ
• CRC Freeze-Off Super Penetrant amzn.to/2wn3BSN
• CRC Sta-Lube Anti-Seize Engine Assembly Lube amzn.to/2uK30Kp
• CRC Sta-Lube Moly-Graph Grease amzn.to/2uJlkTQ
• CRC Throttle Body and Air-Intake Cleaner amzn.to/2x5HMrd
• Loctite Heavy Duty Threadlocker Blue 242 amzn.to/2TqYtF3
• Mobil 1 Synthetic Gear Lube 75W-90 amzn.to/38yHtCh
• Mobil 1 Synthetic Grease amzn.to/38h6ilO
• Permatex Copper Spray-A-Gasket Hi-Temp Sealant amzn.to/2wkt4Mw
• Permatex Dielectric Tune-Up Grease amzn.to/39CcA14
• WD-40 Specialist Penetrant Spray (Blu Torch) amzn.to/3cotcLn
• Scott Shop Towels amzn.to/32Hjwau (optional)
Parts Used:
• Ban Jing High Torque Starter Motor goo.gl/wTTSJn
• Ban Jing Starter Clutch Heavy Duty bit.ly/3cJUxYz
• Dowel Pins 8x10mm Set bit.ly/39B3oKf
• Hoca Crankshaft 2.5mm Stroker goo.gl/1unUmv
• Koso Super Flow Oil Pump goo.gl/GTWZdB
• MotoForce CVT\Flywheel Nut M12x1.25 Serrated bit.ly/3cLiC1a
• NCY Engine Gasket 61mm Set goo.gl/Jqp2Js
• Oil Chain 22 Links goo.gl/ozLb65
• Performance Oil Seal Set bit.ly/2VCyxsI
• Starter Clutch Nut bit.ly/3cJTlo8
• Woodruff Keys bit.ly/39yuaDe
Add-on (optional):
• SSP-G 180cc Big Bore Power Kit bit.ly/2v5ZCd1
• Rocker Arms Tappets, Inlets, Outlet goo.gl/PG17mt
• Chain Guide (standard) amzn.to/2uJDR2i
• Crankcase Bushing 3-Piece Set bit.ly/2Qe6rRd
• Dowel Pins 10x14mm Set bit.ly/39CKaE5
• NGK Spark Plug Iridium CR7HIX bit.ly/2TOopup
• NCY Super Transmission Set goo.gl/hFUSqB
• Bando 835-20-30 CVT Drive Belt goo.gl/dHKAUv
• CVT Cover Anklebiter Ultimate bit.ly/3aG1qIQ
• CVT Cover (longcase) amzn.to/2VUkNcP
• CVT Cover Gasket (longcase) bit.ly/2PWLYQH
• Dr. Pulley 18x14 Sliding Weight 12gm Set goo.gl/1jY5Vh
• NCY Clutch Bell PTFE Coated Racing Star bit.ly/39DtCfo
• NCY Clutch Springs 1000 RPM Blue bit.ly/3aBUVqn
• NCY Compression Spring 1500 RPM bit.ly/2v5Vbil
• NCY Drive Face CNC-Machined Alumin bit.ly/2PYoH0q
• NCY Clutch Nut 39mm bit.ly/38tpwVG
• NCY Gear Set 15*37 goo.gl/U4yPyj
• Taida Rear Drive Bearing goo.gl/yf3qxX
• Zip Ties 12" amzn.to/32GtBo5
Tools Used:
• 8mm Hex Socket amzn.to/39AuO34
• 7mm, 8mm, 10mm, 12mm Sockets w/4" ext. Wrench amzn.to/2vow36J
• 5/16", 9mm Open and Adj. Wrench amzn.to/2vow36J
• 5/8" Spark Plug Socket amzn.to/2LT2kan
• Bearing Separator and Gear Puller Set goo.gl/Vs6C6Y
• Big Head Phillip Screw Driver amzn.to/2vow36J
• Cable Lube Tool amzn.to/2WBvpxy
• Feeler Gauge .004, .005, .006 amzn.to/2wjyiIq
• Flat-Head (narrow) amzn.to/2vow36J
• Flywheel Puller goo.gl/GNToF7
• Heat Gun amzn.to/2uHQU4i
• Hydraulic Compression 12-Ton amzn.to/3axX8mT
• Impact Drill amzn.to/2wsdfDp
• Impact Socket 17mm amzn.to/2uReXOu
• Impact Socket 39mm amzn.to/2PXNjX8
• Mallet Hammer amzn.to/38gJumk
• Multimeter amzn.to/2xe4qhc
• Needle-nose Pliers amzn.to/2vow36J
• Oil Cannister Pump amzn.to/334xxPz
• Oil Drain Pan amzn.to/330TEGM
• Oil Funnel amzn.to/2vR8D9Z
• Propane Torch amzn.to/38g4bPw
• Seal Driver #4, #6, #7 Set Kit amzn.to/38gxwJq
• Slide Hammer and Bearing Puller Set amzn.to/2x53xHE
• Starter Clutch Nut Socket 3.25” min-ext goo.gl/5rMgtS
• Torque Wrench 5-35’ Foot Pounds amzn.to/32O0FL8
• Variator Tool bit.ly/3cqJHGY
---------------------------
Need more info on GY6 BIG BORE KITS?
Visit our Blog Share: ncystore.com/blog

Опубликовано:

11 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 46

@natvega1 Год назад

I just removed the gear with this puller, I had to buy 2 long screws with bolts $2.00, grinded the heads off the screws so they fit into the case, done in less then a minute, it was impossible to get the gear off without the support bolts.

@kalani1963 6 лет назад

You're killing me, just tighten those 2 bolts on the puller clamp a few threads.

@NCYSTORE 6 лет назад

Kawai hao As far as the top nuts that could be tight in a little bit more better sure.

@lesthompson5907 3 года назад

THANK YOU IT SORTED A PORBLOM & NOW I CAN FIS THE CRANK SHAT I HAVE DCRS I CAK TAP THE SHAFT 7 BROKEN BIT 7 FIX THE TIMING UNTIL I GET A NEW CRANK Thanks is helped a lot . as it's a timing only it will do for now. but thank for the video got it , yes I will at some time change the crank ,

@amgharilemzi9244 2 года назад

Merci mon frère pour ta vidéo. J'ai appris beaucoup de toi. Tu es un maître.

@rickhicks2445 Месяц назад

I managed to get my sprocket off with a 3 leg puller and put a large rex clip around them to hold them in place and it popped right off.

@ElSierrno21 7 лет назад

Thank You for your awesome video you do a great job!

@NCYSTORE 7 лет назад

Nicolas Lopez is a fun working on these small engines and its plesure to hear you viewers appreciating our video, thank you.

@GY6-SCOOTERS Год назад

Question buddy my kick starter gear came loose on it's own is their a certain way it faces when sliding it back unto the varriator shaft...? Also I plan on using a long socket to tap it back into place being you already dealt with taking yours off you mind sharing with me how did you get it back on there ....? Thanks

@BigBadLoneWolf 6 лет назад

it is pronounced wood ruff(rough) not wood ro .

@royduncan173 4 года назад

strait claw hammer will remove the kick starter gear of the crank

@raflesia1822 Год назад

awesome video and great job . i have broken bushing kick starter and how to i puller that bushing, wat kind tool use it..?

@salgonzzo1196 4 года назад

Use a c-clamp against the riser bolts to keep it from separating.

@mtlnascarfan 6 лет назад

@10:38 I've never used a gear puller like that before but even I could see that the 2 bottom bolts have to be tightened so that the 2 bottom halves are tucked under the gear wheel. What the hell is wrong with you, man? Using your HANDS to "squeeze them together"?!?!?

@NCYSTORE 6 лет назад

VelociPat keep calm if you look at you have to use a the studs the ties the clamp together are very long barely get in themselves let alone tighten with the nuts. As far as the top nuts that could be tight in a little bit more better sure that's not the end of the world.

@BigBadLoneWolf 6 лет назад

that kind of puller is usually used fro bearings , but works best on the kick start gear

@wadepiehl91 4 года назад

NCY STORE go to the hardware store and buy another set of bolts for the bottom that are bit longer so you can draw the puller halves together. What your doing can be dangerous.

@jackhijo6280 4 года назад

There is an easy way without tools .... a cross switch 17 on the side of the electric stator and hit the gear in the opposite direction to turn slightly

@NCYSTORE 3 года назад

be nice to see a visual what you said.

@roymichaeldeanable 4 года назад

Always interesting...as others can see...I have one of those Pullers....xx

@tebeardenkahboom1 6 лет назад

I'm fixing to watch your videos because I am fixing to put back together a GY6 that I totally split it completely and putting new everything in it I bought a new motor for my buggy and it didn't fit because of a few little things so I'm taking all the innards out of the new one and putting them in my original case. Do I have to put the kickstarter stuff back in it like that gear that was such a pain to get off as I will never use the kickstarter? Plus which one of your videos would be the best one for me to watch to reassemble this thing

@NCYSTORE 6 лет назад

Todd Bearden hi Todd looks like you're going through some challenges here you're able to completely split the crankcase open by removing the kick starter gear however you don't need to kick-start unless you have trouble starting Electric you can do without it just make sure you plug in the CVT cover so no dirt can get into it for the kick-start used to be. If you look at our video channel you can see where it starts talking about the inners of the crankcase assembly, you can start wherever you feel your currently at do I still need to know specifically where you are exactly from installing the Stroker?

@tebeardenkahboom1 6 лет назад

NCY STORE is what I did was split it completely apart and I'm at the very beginning of putting it back together I know I need to put the oil pump in and put the crank in and all that so essentially I would like a video to guide me through the very beginning as if it was a brand new disassembled completely motor

@NCYSTORE 6 лет назад

Todd Bearden if you took out the crankshaft already that means I assume you got the kick starter gear off as well if so we could start here where it begins to put the oil sealed and everything back on including changing and putting though cam chain oil pump exedra here ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-1tPzbqgMsLc.html

@Mikeb8134 Год назад

Do you have to reinstall the kick star gear on the crank shaft or can you leave it off?

@gut3848 Год назад

i have the same problem

@proteusmacapagal1453 6 лет назад

sir how to bring back or install the kickstarter gear? i'm wondering if i remove it i cant bring it back

@NCYSTORE 6 лет назад

Proteus macapagal you can packed it would like a boss and some variator parts recommend using some old parts so apply pressure to the kickstarter gear sprocket.

@proteusmacapagal1453 6 лет назад

i see.. i think that's a good idea i will try it.. thanks a lot for your feed sir i really appreciate

@douglasmanor4427 3 года назад

Thinking about adding a kick start to my 2019 Tao Bull 200 atv,first thing will be installing a starter gear to the crankshaft.Is there a front or back to the starter gear?Are they all 20 tooth plus are the cranks the same size?How far should you press the starter gear onto the crankshaft?

@douglasmanor4427 3 года назад

So the slope on the starter gear on the crankshaft faces the motor?

@dabtech7456 4 года назад

Do you know what size cam this comes with

@onelove8509 7 лет назад

Im having trouble removing that gear...can u tell me what pitsburg item number that is?or probably a link .thanks

@NCYSTORE 7 лет назад

One Love the tibia kind of hit and miss Pittsburgh we got was the smallest size possible, even then you see it wouldn't even fit easily kind of crammed in there

@gerardcollins1767 6 лет назад

can you not tighten the 2 bottom bolts stop it sliding off do that first,then attach top bolts.

@NCYSTORE 6 лет назад

gerard collins that might work well indeed.

@markjohn1584 5 лет назад

do you have 4v engine?

@lion3920 4 года назад

Can my scooter run good if it doesnt have kick starter ?

@lion3920 3 года назад

@Randy Mcilveene Someone is lil bit late hahaha also I now ride without kick start i was only worried becouse i hit it in wall and it start making some noise so i removed it and ride without it and never had problem with my battery dying thanks anyways.

@suyunovshaxzod9301 3 года назад

when you have awesome tool but you cannot even use it that is the worst thing ever

@NCYSTORE 3 года назад

true, made due what I have nut hard to cram in.

@alan-barnes7299 4 года назад

Christ that's painfull to watch. Put camera on a stand in future and put the engine on a proper surface ffs. The amount of times that brand new engine case could of fallen!

@VictorHugo-sf1dh 3 года назад

Rookie missed uselessly tool handling. Two white bottom bolts need to screw it in before you screw the whole thing up for no reason then blaming on tool not working. 😣😥🤔🦂

@NCYSTORE 3 года назад

tight fit, really to do so.