Тёмный

How to Remove + Install/Replace Water Pump and Alternator & AC Belt on 2.5L engine Mazda 3, 6, CX-5 

footprintsinconc
Подписаться 2,9 тыс.
Просмотров 38 тыс.
50% 1

DIY- How to: Remove + Install/Replace Water Pump and Alternator & AC Compressor Serpentine Belt on 2014 to 2020 Mazda 6, 3, CX-5 2.5L 4-cylinder engine
In this video I will show you how to change out two belts: water pump belt and serpentine belt. This repair applies to 2.5L 4-cylinder engine, which can be found in 2014 to 2020 Mazda 6, 3, CX-5.
You might have caught it in the video that the belt tension is leaky. This is a good time to check the belt tensioner as well. Look for signs of it leaking and once the serpentine belt is off, spin the pulley on it and see if you can hear the bearings, it should spin smoothly without making any sounds. If the shock is leaking or you can hear a rough sound, then it needs to be replaced. Here is a video that shows how to replace it:
• How to Remove + Instal...
While you have this area open, check out the water pump and see if it is showing any signs of leaking. See this video to see the early signs of water pump leaking and how to replace it.
• How to: Water Pump & ...
I might have given a little too much detail, but I think having the extra details, would help someone who might get stuck on not understand how it exactly goes.
The passenger side of the car needs to be jacked up for this repair because you will be working in the area behind the wheel. Learn how to jack up the car and position jack stands under the vehicle to supported it safely in the following video.
• How to: Jack or Lift u...
Correction in the verbiage in video: • How to Remove + Instal...
-the most conservative crack count i found was "3 or more cracks with in a 3" section of the belt" not 1" section of the belt as stated in the video...is when the belt should be replaced.
-Also note, if the cracks are deep, then you should be replacing the belt.
Mazda part number:
-serpentine belt for the ac compressor and alternator -- PY01-15-909A
amzn.to/3KOZwZB
-water pump belt PY01-15-908
amzn.to/3ReKvT8
I used Mazda parts, but you can use the gates products as well. They are a great quality part as well. They do produce and supply belts for different manufactures. Here are some links to those...they Mazda parts couldn't be bought from Amazon. Serpentine Gates Belt:
K060380 Multi V-Groove Belt amzn.to/3rjxFa0
Gates Belt for water pump amzn.to/2UmY2jt
Serpentine Bando USA 6PK965 amzn.to/3B8ldhY
Please check out the Mazda 6 Playlist:
• Mazda 6
As Always, SAFETY is first. Use all the precautions and safety equipment and gear at all time…depending on what is being done that includes, gloves, glasses, mask, etc.
Thank you for watching.
Please like, share and subscribe! Thank you!
Affiliate links, at no cost to you for:
Non battery-operated Pressure gauge w/ bleed button & hose: amzn.to/3622GJC
Air pump: amzn.to/3DWRdri or amzn.to/3xhkuLS
tire tread depth gauge amzn.to/3jr5e6X
Try Amazon Prime for 30-day Free Trail amzn.to/3G8TSgP
Kindle Unlimited Membership Plans amzn.to/3g5oSUm
Try Audible Plus amzn.to/35nVOp6
Try Audible Premium Plus and Get Up to Two Free Audiobooks amzn.to/3G8UaUX

Хобби

Опубликовано:

 

18 июл 2021

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 90   
@NikoRoma
@NikoRoma 16 дней назад
With shops and mechanics trying to upsell and rip off unsuspecting people so often, its nice to get an idea of what needs to be done so you can either do it yourself or decide if their quote is reasonable or not. I appreciate you taking the time to do this. Liked, subscribed, and commented. I hope your channel grows and you are able to profit from it. It's time consuming to put video content together and not enough people show their appreciation.
@techouse16
@techouse16 22 дня назад
Amazing demonstration with a great explanation on each step! thank you!
@BrandonMassey
@BrandonMassey Год назад
I have a 2013 2.0L Mazda 3 and this video was perfect at showing me how to replace both my belts. Thank you.
@footprintsinconc
@footprintsinconc Год назад
you're welcome! please make sure to help by liking & sharing!!
@fortknox4804
@fortknox4804 Месяц назад
Thank you!!!! I did EXACTLY what you did. I was stuck with the same wrench setup too which is what made this vid so helpful.
@abrahamarango843
@abrahamarango843 Год назад
Thank you for your help! Fixed my car today. My belt broke and replaced both serpentine and the stretch belt with your help
@footprintsinconc
@footprintsinconc Год назад
Excellent!
@dtuck552011
@dtuck552011 Год назад
I would like to add my thanks for your very helpful advice. My serpentine belt broke on my 2017 CX-5 at 63000 miles. I tried my best to use a 17mm combo wrench and it was hopeless. I invested in a 17mm offset and it was smooth sailing. Thanks again!
@footprintsinconc
@footprintsinconc Год назад
Awesome!
@jstone1211
@jstone1211 11 месяцев назад
yep, before you start just get the 17mm offset wrench. about $15 and you will save yourself time....
@nigelwalsh9464
@nigelwalsh9464 Месяц назад
Great video, well lit, and you dealt with all the detail so literally anyone could or at least try to do this job. Thank you....
@MostGenericUser
@MostGenericUser Год назад
This is a really good descriptive and informative video. Thank you for uploading this Just an fyi I think you added a 1 to the end of the part number for the water pump belt in the description. I appreciate that you put all that info in the description too it nice to not have to hunt for part numbers too or other videos you referenced
@footprintsinconc
@footprintsinconc Год назад
Thank you! Really appreciate you pointing this oukt!! I've updated the part numbers.
@goliverpool3563
@goliverpool3563 5 месяцев назад
Great job explaining what to do. Appreciate your clarity.
@footprintsinconc
@footprintsinconc 5 месяцев назад
Thank you!
@smb1014
@smb1014 2 года назад
Excellent video. I need to change my belts on my 2017 CX5. This was super helpful.
@footprintsinconc
@footprintsinconc 2 года назад
Thank you!! Please help me out with RU-vid algorithms by liking and sharing. Thank you!
@kevinkennedy7631
@kevinkennedy7631 Год назад
I have 2016 Miata ND and did it from the top. Removed air box and got decent access. Tensioner hex was 18MM and crank shaft 21MM. At 61590 miles the serpentine belt had a crack but overall was in good shape. It could have gone more miles but once I had everything out to inspect it I just changed them both. I used Continental 4060374 and 4030330S replacement belts. Re-installing water pump belt was PIA - a midsize ratchet with flex head would have made the job easier. Stabilizer bar made job much harder. With water pump belt positioned on top of crank shaft (in groove) and bottom of water pump pulley I wedged my hand under coolant hose and just pushed to get tension belt seated. Serpentine belt was easy. Another example of why mechanics hate engineers :)
@footprintsinconc
@footprintsinconc Год назад
nice job and details! lol, i hear you. i know your comment is from a joking point of view. over the years i think i've come to understand this as....still can't explain all the things, but here is my thought: you have to remember that we all tend to view things from our own lenses and things aren't as clear as they are to us...as an engineer, there are a ton of things that even i wonder WTH! but in business, they apply the same item in multiple different makes, models, and years, so the surroundings change but the engine itself doesn't and so we find these weird fits and situations. there isn't any money for them to re-engineer items to make them better as they are don't with that phase and there must have been only a little bit of overlap to make sure things worked, but that is it....they don't see any more engineering giving them any more of a return on the car since it still sells for the same price, so they don't bother adding more cost into it....this results in all the frustration of those that work on the cars. since there isn't a feedback chain, things don't change either....the feedback chain that they have, don't and won't pick up on all the stuff that you and i see and do.
@tjacobsen5131
@tjacobsen5131 2 месяца назад
Thanks for posting this comment. I just lost my serpentine belt on my 2016nd at 150.000 km on a trip and ordered a new tensioner and both belts. I need to go back by bus and replace it. I can see that it's the same setup as on the 2.5L engine, though I will be able to do it from above with the hood open. Thanks for sharing. Wish me luck 🤞🏻😅
@Jim1457a
@Jim1457a 3 месяца назад
Nicely done, thanks for posting! 👍
@JamesBackes4335
@JamesBackes4335 2 года назад
This helped me immensely! It's good to note that turning the pulley with the wrench/socket set is probably the best thing you can do (if people weren't already doing that) The Water Pump pulley on the CX-5 is high behind a frame member, so be aware that it's not as easy as shown as the OP is on a different model. Not that it changes the procedure, but it's tricker to get your hand in there. Excellent Job!
@footprintsinconc
@footprintsinconc 2 года назад
Thank you for the kind words! Good point you make on the CX-5. Thanks for sharing. Please help me out with the RU-vid algorithms by liking, sharing and subscribing.
@mikeyd0123
@mikeyd0123 2 месяца назад
yep, just did serpentine and water pump belt on my CX-5 today, getting that on was a 2 person operation especially with no lift, very tight! Anyway great video, very helpful.
@TheSinner1922
@TheSinner1922 2 года назад
Bro, thank you!! You helped me out tremendously today. And probably saved me some money lol
@footprintsinconc
@footprintsinconc 2 года назад
Thank you! Please help out with RU-vid algorithm by liking and sharing! and the affiliate amazon link to help the channel. Thank you!
@gabeholguin630
@gabeholguin630 10 месяцев назад
Thank you for the instruction, it was HUGELY helpful!
@footprintsinconc
@footprintsinconc 10 месяцев назад
Glad it was helpful!
@RM-kt4yq
@RM-kt4yq Год назад
Thank you …. Nice job … the video very clear, step by step 👍
@footprintsinconc
@footprintsinconc Год назад
You are welcome! Please be sure to like and share
@jasonligo895
@jasonligo895 2 года назад
This video was nice and clear!
@footprintsinconc
@footprintsinconc 2 года назад
Thank you! Please help me out with RU-vid algorithms by liking, sharing and subscribing!! Thanks!
@mrleyva26
@mrleyva26 Месяц назад
Great video!
@protem_music
@protem_music 7 месяцев назад
great and thorough video. many thanks
@footprintsinconc
@footprintsinconc 7 месяцев назад
You are welcome!
@tube4knowledge346
@tube4knowledge346 2 года назад
Excellent video! thank you!
@footprintsinconc
@footprintsinconc 2 года назад
Thank you!
@bocap1980
@bocap1980 Год назад
Outstanding details 👌 subbed
@footprintsinconc
@footprintsinconc Год назад
Awesome, thank you!
@freddybermudez8501
@freddybermudez8501 10 месяцев назад
Great video thank you !
@footprintsinconc
@footprintsinconc 10 месяцев назад
thank you!!
@tjacobsen5131
@tjacobsen5131 2 месяца назад
Thank you very much
@JohnBaker3000
@JohnBaker3000 Год назад
Nice! I’ll give it a try!
@footprintsinconc
@footprintsinconc Год назад
good luck!
@HardCorps88
@HardCorps88 Год назад
You can do from top down. Use half inch rachet with 17mm socket. Right arm to hold rachet while threading your left arm down side of engine. Be sure to place belt on crank first then holding tension thread under pully and around A/C. Then again...im 6'5" and got long arms. :)
@footprintsinconc
@footprintsinconc Год назад
thanks for sharing. there are many ways to do the same job.
@videoworks7731
@videoworks7731 3 месяца назад
thank you
@pedromateo1597
@pedromateo1597 Месяц назад
Ty so much!
@mickmickers5171
@mickmickers5171 2 года назад
Great video. My water pump belt is making noise. It is off track. It's on the outside of the crankpulley which it shouldn't be so some mechanic clearly messed that up. I'm gonna be doing this project soon. Kinda nervous and excited
@footprintsinconc
@footprintsinconc 2 года назад
Don't be. Enjoy the process and don't be stressed
@indoperfect4068
@indoperfect4068 14 дней назад
thanks for this very clear and helpful video, I'am tackling this DIY pretty soon as I have a japannese market impo 2015 DJ Demio Diesel 1.5 Skyactive. I'm looking for the part numbers for both belts if someone has the oem system available please will be helpful thanks again keep rollin'
@fahadpasha546
@fahadpasha546 3 года назад
Thats great.....👏
@footprintsinconc
@footprintsinconc 3 года назад
Thank you
@meligala11
@meligala11 Год назад
What size is the socket used on the crank?
@daveverdonschot7956
@daveverdonschot7956 2 года назад
Nice job... not a lot of room. You could also just cut the old belt for the water pump.
@footprintsinconc
@footprintsinconc 2 года назад
thank you. good point on cutting the belt. but i wanted to show it removed just incase someone is looking to remove it. i always keep the belts that i remove as back up for my cars.
@vincenttran6938
@vincenttran6938 Месяц назад
Dumb q, I'm just replacing the serpentine, so do i need to mess with the water pump belt at all or can i just skip straight to the tensioner?
@TavosMr
@TavosMr 2 года назад
Good information, just one question, you said turning counterclockwise, but you are turning the pulley clockwise.
@footprintsinconc
@footprintsinconc 2 года назад
good catch. what do they say...do as i do and not as i said :) turn it clockwise as i did in the video.
@SmartLifeSolutionsWork
@SmartLifeSolutionsWork 6 месяцев назад
I am trying to change just the serp belt, but the editing of this sub-video link that specified in text to click here to change the serp belt, has a lil other video info that i dont think helps me to do just the serp belt. From 5:25 to 7:25 and also from 8:30 to 10:45 is about the water pulley belt. Do i need to do any of that stuff in order to change my serp belt only? The editing confuses me if this sub-video is intended just for the serpentine belt. Can u fix or explain why i need to do it if not changing my water pulley belt?? Im a single female that youtubes car maintenance. lol Thanks!
@footprintsinconc
@footprintsinconc 5 месяцев назад
in this video, i am showing how to remove and install all the belts I don't know the mileage of your car. if the other belts have not been changed, it's probably a good thing to change those out too. for serpentine belt ONLY: 2:39 to 5:25 is how to remove the serpentine belt 7:05 to 8:25 information on the serpentine belt 10:46 to 14:08 is how to install the serpentine belt
@jimcastillo8950
@jimcastillo8950 6 месяцев назад
Hello, while turning the crankcase the transmission is still in the the Park Section? and parking brakes on? thanks
@footprintsinconc
@footprintsinconc 6 месяцев назад
the car should turned off, your parking brake should be one if the rear tires are on the ground. you will then proceed to turn the crankcase...it has no effect on the transmission or the tires turning.. this is no different than , while in park with the parking brake on, you turn the ignition key or press the start button. the crankcase gets turned by a starter.
@gunit5310
@gunit5310 Год назад
Turning the crank shaft counter clock wise doesn't damage the engine?
@footprintsinconc
@footprintsinconc Год назад
No it doesn't.
@shininginshadows
@shininginshadows 2 года назад
What's the best approach to going after the alternator itself? From the wheel well?
@footprintsinconc
@footprintsinconc 2 года назад
hi. for the belt, from the wheel well for the alternator from the top...remove and install.
@shininginshadows
@shininginshadows 2 года назад
@@footprintsinconc Thanks. Discussing getting one of these for my wife, trying to determine how much of a headache potential will be.
@footprintsinconc
@footprintsinconc 2 года назад
@@shininginshadows getting a mazda or getting belts/water pump, etc to do yourself?
@shininginshadows
@shininginshadows 2 года назад
@@footprintsinconc Getting a Mazda. Low enough miles that I shouldn't have to deal with the for a while, but like to be prepared
@footprintsinconc
@footprintsinconc 2 года назад
@@shininginshadows they are great cars. if you get an accord for the same price, i'd do that. i'd go with either, accord would be my first choice.
@sebbbou5455
@sebbbou5455 Год назад
Is it worth it to replace the water pump at the same time? Or it could last longer than the belts?
@footprintsinconc
@footprintsinconc Год назад
Honestly, it depends on the milage of the car. If you are over 150k, and doing the belts, then might as well do it. Otherwise check to see if the leak indicator hole is showing any signs of coolant leak...If it is, then you should change it regardless of the milage.
@becketthan8223
@becketthan8223 Год назад
Would this be helpful for a 2010 2.5L Mazda 3?
@footprintsinconc
@footprintsinconc Год назад
it should be. the basics are the same
@footprintsinconc
@footprintsinconc Год назад
should
@TStark-xs5cj
@TStark-xs5cj Год назад
Are we supposed to turn it clockwise or counter clockwise?
@footprintsinconc
@footprintsinconc Год назад
turn it in the direction that i'm showing in the video...sorry, lol, its the other right, or in this case the other counterclockwise :) so clockwise
@TStark-xs5cj
@TStark-xs5cj Год назад
@@footprintsinconclol ty I wanted to make sure I’m actually on the way to pick up the belt now and replace it
@rafaelpalacios2948
@rafaelpalacios2948 Год назад
why not cut off the old belts over rotating them off?
@footprintsinconc
@footprintsinconc Год назад
You certainly can do that.
@AlexRivera-dm1wg
@AlexRivera-dm1wg 2 года назад
I don't know where you got that wrong info . But even if there's only one little crack on the belt. You have to replace the belt . I have 22 years experience. And if a belt is worn or cracked. You have to replace it . Unless you want next to cut off the alternator and overheat the engine. 🤦‍♂️
@footprintsinconc
@footprintsinconc 2 года назад
thanks for your comment. simply googling returns results like, they all have many years of experience as well...wide variety of opinions... www.cartalk.com: "Tiny cracks in a serpentine belt aren't necessarily bad, but the deep ones here mean it's running out of time..." www.aa1car.com: "...A good rule of thumb for older chloroprene-based serpentine belts (neoprene belts) is that if cracks are observed 3 mm (1/8 inch) apart all around the belt, the belt is reaching the end of its service life and should be changed..." www.colonyoneauto.com: "The general rule is if there are three or more cracks within a three-inch section of the belt, then your belt needs replacing." i was quoting the last quote as being the most conservative...so should have said "...with in a 3 inch section", not "1 inch section"...so i'm updating with this in my notes under description.
@TStark-xs5cj
@TStark-xs5cj Год назад
It looks like you spun the pulley, clockwise
@footprintsinconc
@footprintsinconc 11 месяцев назад
I sure did. It was opposite to what I said :)
@jimwestbrook4068
@jimwestbrook4068 Год назад
Well you did it, but that was a little backasswards way of going about it.
@TStark-xs5cj
@TStark-xs5cj Год назад
Please post the link to your video with a better way of doing it
@franciscocarrera6188
@franciscocarrera6188 5 месяцев назад
Why not just cut the old wp belt? Lol
@footprintsinconc
@footprintsinconc 5 месяцев назад
you definitely can. However, if you didn't want to or needed to remove the belt and put it back on, you need to remove it without cutting it :)
@docholiday5682
@docholiday5682 3 месяца назад
Save time. Cut off the water pump belt instead of taking all that time to remove it. Second use a $10.00 Stretch Belt Installation Tool.
Далее
2014-2021 Mazda 6 2.5 Serpentine Belt Replacement
19:26
World Record Tunnel Glide 🪂
0:19
Просмотров 30 млн
Что она делает?
0:34
Просмотров 12 млн