How To Remove The Engine From The Frame | Upper Overhaul Engine Ep #1 OF 7 | CBR250R 2013

Подписаться 1,2 тыс.

50% 1

00:00 Opening
00:04 WARNING
00:11 Removing The Covers
02:13 Draining The Engine Oil
02:32 Draining The Coolant
03:24 Removing The Fuel Tank
03:41 Removing The Air Box
03:54 Remove The Throttle Body
07:19 Removing The Exhaust • MUFFLER + PIPE | Assem...
07:48 Removing The Drive Sprocket Cover
08:01 Removing The Clutch Cable Guide
08:46 Removing The Starter Motor Cables
09:31 Disconnect The O2 Sensor CONNECTOR
09:53 Perhaps, to protect the O2 Sensor... it is better to remove it as well.
10:50 Remove The Gearshift Arm
11:20 Remove The Drive Sprocket
12:37 Disconnect The Water Hoses
13:18 Disconnect The Spark Plug Cap
13:52 Disconnect The Connectors: Alternator 3P, CKP Sensor/Neutral, Switch 6P, VS Sensor 3P, ECT Sensor 3P
14:29 Release The VS Sensor WIRE
15:02 Disconnect The Connector ECT Sensor 3P
15:22 Disconnect The Cooling Fan 2P Connector from The Frame
16:24 Building The Engine Adjustable Support
16:47 Removing The Three Front Engine Mounting Screws & Hanger Plates
19:20 For Frame Protection, Tape The Frame OR Wrap the head of the motor with a towel
19:39 Removing The Two Rear Engine Mounting Screws
21:11 Lowering The Engine & Remove It From The Frame
22:32 While Removing The Engine Be Careful Not To Damage Parts
23:19 Credits

Авто/Мото

Опубликовано:

29 июн 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 10

@vnnavin 6 месяцев назад

Very nice.👌👍

@harshwardhanvairagade7932 6 месяцев назад

I like your work ❤.

@stuarthipkins8336 6 месяцев назад

Excellent job..i like no talking..lighting perfect..i just did my valves.spark plug. N fuel filter..200.00 in parts..it was a huge pain in the ass..2017 cbr 300.

@mycbr250rdmotorcycling7 6 месяцев назад

Yes. Adjusting valves with an engine inside the frame is a big headache. According to Honda's recommendation, I thinking, this is a test that is outside the time of the warranty. Otherwise they would make sure it was a friendlier process. Didn't it? When the engine is removed from the frame, adjusting valves is a piece of cake.

@karmasters 6 месяцев назад

@@mycbr250rdmotorcycling7 Yes, I believe a lot of todays bikes are made in a "clever" way by the manufacturers. On average you will run out of warranty before you need to do serious maintenance. But also for high mileage bikes within warranty times, the dealerships actually don't check valve clearances but they charge you for them "checking" that the bike seems to run ok with no error codes.. That has been my observation. I can also say that has been my experience of people i know. I am used to working on machines so i can say i do not believe that someone can ride in their bike at 1100 into a bike shop and get it back at 1500 with a valve check/adjustment done. Yet i have seen this again and again with people I know. Valve checks need at least a cold engine. Anyway, I am very impressed with your patience and hard work! Wish you all the best with the bike and all the best for 2024!

@calgapx1705 6 месяцев назад

Thanks, good video. Why were you taking your engine out? Problems or just maintenance?

@mycbr250rdmotorcycling7 6 месяцев назад

A problem. The big one. I found oil in my plug.

@calgapx1705 6 месяцев назад

Oh dear, not good! Just need a rebore and piston perhaps? Or is it valves?

@mycbr250rdmotorcycling7 6 месяцев назад

@@calgapx1705 Honda does not sell oversize piston. Therefore if you want to stay with original parts you have to buy a NEW set of piston and cylinder. Maybe there are sites that sell an oversize piston, and then it is possible to fix the cylinder by honning or rebore+honning. Along the way I also did valve polishing, because it was necessary.

@calgapx1705 6 месяцев назад

Good luck anyway!