LITERALLY my compressor just got delivered 10 min ago. Between this video and the one Brothers in Air did, I think I’ve got this covered. Off to do yard work then maybe some target practice this evening. 😁👍
Does this compressor have to be oiled through the brass grommet on the cooling fan side of the compressor located just above the top left corner of the cooling fan after so many fills? I have the TXET062 and it looks similar to the nomad which has an identical brass grommet.
How can you buy parts? I have a cracked line in one I just bought on Amazon. The coiled line inside leaks from the crack and it won’t build pressure, brand new first use, doesn’t work.
Hi Tuxing CN , what’s the time interval to put silicone oil and how can I put in ? I just received my order from your store from AliExpress and I want to know if compressor have silicon oil or not from the beginning! Thank you 🙏
Hello, thank you for your order. Locate the lubrication hole on the left hand side of the unit. Using any silicon oil, like 100% treadmill oil, apply 2-3 drops of silicone oil every 5 fills or1.5 hours of use (whichever comes first). It has silicon oil inside at the beginning. Thank you and have a nice day!
I just got my brand new compressor, the problem is it build pressure some times and it won't some time. very strange behavior. Since it's building pressure , I don't think it's issue of Orings or any leakages. What should I check for ? .
Would someone from Tuxing CN list the silicon grease and silicon lubricant used in this video, thank-you! Also, do you have rebuild kits with o-rings, gaskets, etc. or the exact sizes needed.
I just removed the large nut on the top of the canister. I used a curved hook to pull the filter out. Take notice of how far down the filter is from the top of the opening and when replacing try to put it close to the same depth. I don't know if the depth is important, I'm just saying that is what I did.
In order to make us get very good quality air, we installed one filter inside ( We think other suppliers seldom do like us), we need to replace the cotton after long usage. Such as fill 20~30 times 0.5L gas cylinder from 0- 30Mpa
Sir i need your help. Where can i get its o rings and repair kit. Already i bought this compressor from my local gun store but they don't keep service kit. Please let me know where can i get
Use only high pressure lubricants, like pure silicone or teflon grease or oils. Never use motor oil style lubricants, they’re flammable at high pressure.
Hello, my compressor loads up to 10 bar and then the fuse burns, I change it but it can't go any higher and the fuse burns again. what could be the problem
Maybe your tronsfomrer/Conventer is not connect well, make it burn. Repalce the fuse from packing list and make sure the imput voltage is 12V at the same time
@@sergeiballer6021 Внутрь механизма закладывал голубую смазку для авто покупал. И перед каждым запуском компрессора в отверстие забора воздуха капаю жидкую силиконовую смазку. То есть в поршневую попадает жидкий силикон. Можно наверное смазку которая в пневмоинструменте используется. Я еще хитрю - когда включа. от 220 вольт то к отверстию забора воздуха ставлю блок питания (а в нем так же вентиляторо и через него прогоняется воздух. Этот воздух уже под давелние идет и попадает в сам компрессор. Так у меня температура где то 55-60 максимум. Больше не поднимается.
Ужасное качество компрессора!!Сломался через месяц использования.Гарантии нет,покупал на Али экспресс! Продавец сказал,что все запчасти надо покупать за свой счёт.
Я написал продавцу дважды и дважды он мне помог с запчастями абсолютно бесплатно в рамках гарантийного ремонта. Гарантия 1 год. Качество соответствует стоимости. Дешевле компрессоров нет.
Набор запчастей для полного обслуживания стоит около 10$. При минимальном слесарном инструменте и опыте, за пару часов он полностью обслуживается или ремонтируется. Главное чтоб двигатель был целый и электроника, а остальное все не дорогое и легкозаменимое.