Тёмный
No video :(

How to Replace a Blend Door Actuator in a Jeep Wrangler JK 

The BFH Garage
Подписаться 25 тыс.
Просмотров 36 тыс.
50% 1

CLICK-CLICK-CLICK-CLICK-CLICK.....how to eliminate that annoying sound!
The process of replacing a blend door actuator can be very frustrating. This video is intended to help take some of that pain away! Blend doors may need recalibration after replacement.
Disclaimer: The following disclaimer applies to The BFH Garage RU-vid channel (referred to as "the Channel"). By accessing or using the Channel, you acknowledge and agree to the terms and conditions of this disclaimer. If you do not agree with these terms, please refrain from accessing or viewing the Channel.
Content: The Channel provides automotive-related content, including but not limited to repair guides, maintenance tips, product reviews, and general information. The information presented on the Channel is based on the personal opinions and experiences of the Channel's creator and contributors. However, the Channel makes no representations or warranties of any kind, express or implied, about the completeness, accuracy, reliability, suitability, or availability of the information, products, or services mentioned. The content is provided for informational and entertainment purposes only and should not be considered professional advice.
Personal Responsibility: The Channel encourages responsible automotive practices. However, any actions or decisions you take based on the information provided on the Channel are solely your responsibility. The Channel cannot be held liable for any damages, injuries, or losses that may occur as a result of following or implementing any information or advice presented on the Channel. Always exercise caution, consult professionals, and adhere to safety guidelines when working on or modifying vehicles.
Third-Party Content and Links: The Channel may include links to third-party websites, products, or services. These links are provided for convenience and informational purposes only. The Channel does not endorse or have control over the content, products, or services offered by third parties. Accessing or using third-party content is at your own risk, and the Channel shall not be responsible for any damages, losses, or issues arising from such content.
Intellectual Property: All intellectual property rights, including copyrights, trademarks, and any other proprietary rights, in and to the Channel's content (including videos, images, graphics, logos, and text) are owned by or licensed to the Channel. You may not reproduce, distribute, modify, display, perform, or otherwise use any content from the Channel without obtaining prior written consent from the Channel.
Changes to the Disclaimer: The Channel reserves the right to modify, update, or change this disclaimer at any time without prior notice. It is your responsibility to review this disclaimer periodically for any changes. Your continued use of the Channel after modifications to this disclaimer will constitute your acknowledgment and acceptance of the modified terms.
Governing Law: This disclaimer shall be governed by and construed in accordance with the laws of the jurisdiction in which the Channel operates. Any disputes arising out of or in connection with this disclaimer shall be subject to the exclusive jurisdiction of the courts in that jurisdiction.
If you have any questions or concerns regarding this disclaimer, please contact us through the appropriate channels provided on the Channel.
Last updated: May 11, 2023

Опубликовано:

 

26 авг 2024

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 73   
@Mike__P
@Mike__P 28 дней назад
Excellent video. The passenger actuator was making a noise on mine, but I replaced it and it still made the noise. It turned out the gears on the actual door itself were cracked and not able to engage the actuator. Didn't know how to fix it so I just unplugged the harness because the noise was driving me crazy. Now I hear another actuator starting to make noise. These Jeeps aren't the most well made...
@drewb5738
@drewb5738 9 дней назад
Thanks. You explained enough to make this as easy as possible. Glad I only had to do the driver side (for now).
@mikemartinez842
@mikemartinez842 6 месяцев назад
Great video. I did mine by putting a pillow between the seats and laying across them on my right side. It was comfortable enough that I didn't get cramped up and I had decent leverage to remove both screws.
@jnaberg1
@jnaberg1 3 месяца назад
I just changed out my passenger side actuator. Your video was very helpful. I was actually able to go in from underneath and behind the actuator with a 1/4” drive ratchet and 7mm to get the rear screw. Also, my splines would not line up to install the new one, so I opened up the screen door to the blender and lifted the door all the way up and it lined up perfect. Turned the jeep on and tested, all is right in the world now.
@marlinmessenger3654
@marlinmessenger3654 Месяц назад
Your video is very easy to follow. I haven't done it yet, but when the part gets here I can do this with knowing how to do it! Thank you!
@johnfalco9528
@johnfalco9528 8 месяцев назад
Just did this job today along with the hvac control module. I just unbolted the whole module in front of the actuator rather than disconnecting it from the frame. I doubt it made it any easier than your way since many choice words were uttered in my process along the way lol. But great filming and precise explanation in your video! Makes me wish I looked for your video before I finished my installation 👍.
@johnfalco9528
@johnfalco9528 8 месяцев назад
I should add I did the drivers side
@888Jt88
@888Jt88 18 дней назад
Thank you! This is literally the best video on RU-vid!
@brianbaughman186
@brianbaughman186 5 месяцев назад
Thank you. This is exactly what I was looking for, for the passenger side unfortunately. I will use this and attack the problem. Excellent video along with precise explanation.
@davidjeansonne3706
@davidjeansonne3706 8 месяцев назад
I have the passenger side clicking on my daughters Jeep dreading this challenge thanks for the tip’s great video
@RES-mw4sf
@RES-mw4sf 6 месяцев назад
Do you need to position the recirculating blend door in any position before installing the actuator?
@ItchyBurrito
@ItchyBurrito 14 дней назад
Great video. I had to do this on my 15 JKUR but unfortunately my duct would NOT come out. Got it done though. Doesn't seem like the force of my a/c goes as hi now though.
@thehoofandhearse1125
@thehoofandhearse1125 3 месяца назад
Thank you for such a thorough explanation! I wish more videos were like yours! Thanks again!!
@rhqfree
@rhqfree 7 месяцев назад
Mike ,, Thank you very much man, very helpful .I replaced mine step by step with your video. Thanks again !!!!
@omarcaballero9680
@omarcaballero9680 7 месяцев назад
Glad to have run across your video. Appreciate the details and lessons learned. I will undertake this task in the coming weeks when the weather goes above 0!
@omarcaballero9680
@omarcaballero9680 7 месяцев назад
Hello, so I was successful in performing this surgery thanks to you and the great directions. I did this to address my all-hot all-cold no warm issue but it did not make a difference. It still shoots all cold (left rotation) or all hot (right rotation) but trying to get it into the warm setting/area...no go. Any ideas? Thanks again.
@jayfranco9969
@jayfranco9969 День назад
Thank you so much for this video 🙏🏻 god bless
@johnturley5595
@johnturley5595 Месяц назад
Wow simply great instructions .................... My 2014 wrangler blowing cold air on passenger side only .... hope its that blend actuator ...
@ncfitton
@ncfitton 7 месяцев назад
Great video! I can report, that my driver side actuator wasn’t working because the plastic ring gears inside the case were not correctly aligned. I had to take them out and realign them and now the door works perfectly. They must have jumped during my last wheeling trip. You need the missing tooth to hit that line when you are on full heat.
@ninjaryder1st
@ninjaryder1st 2 месяца назад
opened my box up to find the "plastic post" that mounts the top white gear was completely sheared off.. gotta love cheap plastic #$%^ (CPS)
@travisandmissydog
@travisandmissydog 6 месяцев назад
Just wait until you have to change out your PCV valve. That small thumb driver might be your ticket as there is no room back there. Thank you for making this video as now I know where all three are. At least they make all the actuators the same! Better than dealing with three different types in three locations.
@ajschwartzii
@ajschwartzii 8 месяцев назад
Hey Mike, great video. I appreciate everything you do to help us DIYers as I rely on your videos and reference them often. Just a thought. I know a lot of folks might not want to do this, and I don't even know if it would be possible, or even help in the long run. But, could you use a "1/2 inch hole saw (or larger) and cut a hole in the firewall to better access that passenger side blend door actuator screw? Easy enough and could be plugged with commonly available firewall plugs. Would never be seen again by most, and would be available to use down the road should this exercise be required again. Just a thought. I realize that this wasn't your Jeep so cutting holes is probably not "okay" but seems like a reasonable method. I'm about to have to attempt the same thing on a 2015 F-150 Platinum so please wish me luck. Thanks again for all that you do. You have no idea how grateful I am to have you as a resource. Best wishes. -Andy (down the street from you in H.R.)
@TheBFHGarage
@TheBFHGarage 8 месяцев назад
I wouldn't do that just for rust purposes, but you could I suppose. Glad these videos help you out!
@AlSutton-k9c
@AlSutton-k9c Месяц назад
Easy to follow video. Thank you for making it simple. I did notice that after I change it my engine light came on. Do I have to reset anything?
@TheBFHGarage
@TheBFHGarage Месяц назад
@@AlSutton-k9c what is the check engine code?
@larryjust824
@larryjust824 8 месяцев назад
One of the best videos on this I've seen, thanks.
@charlies7658
@charlies7658 День назад
Life saver. Thanks
@southwest7977
@southwest7977 7 месяцев назад
I did this job today…1 part from rock auto had too small of a spline. Had to buy one from O’Reilly’s. 2. Actuator is slightly canted which threw me for a loop until I realized that there was an alignment notch next to the upper screw. That made it way easier to get the screws lined up and back in place. 3. I started the Jeep with the TCM still unplugged to test the actuator. Then put it back together and took it for a drive. When I restarted it,it threw a check engine light for lost connection to the TCM. It should clear when the Jeep tests it again but it’s still on after the test drive.
@charlies7658
@charlies7658 Месяц назад
Absolutely great video. AC suddenly stopped blowing cold air and has started back again. I hear that same clicking sound but only on drivers side yet passenger and driver side are blowing hot air. Question: if driver side actuator is bad will passenger side still blow cold air?
@TheBFHGarage
@TheBFHGarage Месяц назад
@@charlies7658 that I do not know
@ernestoadorno9434
@ernestoadorno9434 29 дней назад
Thaks very helpful
@RES-mw4sf
@RES-mw4sf 6 месяцев назад
Temp Control-Left Blend Door Control and AC Knob, Recirc-Right- Recirculation Door and Fan Speed Control Knob , Front Mode-Air Flow Direction Middle Blend Door and rear window defroster Knob. My JSCAN tool I use to calibrated the doors after installation.
@chelseahuffman2170
@chelseahuffman2170 7 месяцев назад
The first module you remove… what is it? Because it’s not in my 2011.
@ScottM-z1l
@ScottM-z1l 16 дней назад
OMG. The passenger side actuator had me scream swearing. I then tried coming at it from the driver's side, through the glove box opening and i could access the screw closest to the engine much easier. Also bought a disc like you had but mine ratchets. Went much easier with that tool using my right hand. I'm right handed btw. Thanks for the video!
@TheBFHGarage
@TheBFHGarage 16 дней назад
@@ScottM-z1l Glad you got it figured out!
@adrian6892
@adrian6892 7 месяцев назад
Got stuck with the rear bolt on the passenger side actuator. Heading to the hardware store to pick up a palm ratchet
@MrJpakers
@MrJpakers 9 месяцев назад
Did this last month was a monster.
@therealrealshocker
@therealrealshocker 7 месяцев назад
Awesome video. Thanks for sharing 🙏
@davidwoods7973
@davidwoods7973 3 месяца назад
Great educational thank you
@chrislynch3575
@chrislynch3575 3 месяца назад
Just did this it's a bit of a pain because of the tight space but working fine now, however my jeep now shifts rough from park to reverse or drive. Wasn't doing it before the repair. Fml
@williamlee7782
@williamlee7782 Месяц назад
The dealer diagnosed a failed blend door actuator as noted on my report (which I replaced with a Dorman brand 8 months ago for the driver's side). Worked great. Lately, I have weird AC issues; took it to dealer and they said my blend door actuator is bad. After watching this video, I realized there are 3 blend door actuators. How do I know which one is broken?
@TheBFHGarage
@TheBFHGarage Месяц назад
@@williamlee7782 you can hear it. The one in the middle is easy and most likely not it. The one on passenger side has easy access to see but difficult to replace.
@williamlee7782
@williamlee7782 Месяц назад
@@TheBFHGarage thank you. I pulled the glove compartment out and the passenger side actuator works fine. I've no clicks anywhere. When the driver's side failed, the motor failed so I replaced the unit. I now hear the driver's side working which leaves the center. Do you know how I can get the center one to actuate? ps: I don't have blower function and dealer thinks it is my TIPM but can't diagnose without me spending more than the $200 they already earned to tell me that the blend door actuator is not working. 😅
@williamlee7782
@williamlee7782 Месяц назад
@@TheBFHGarage I checked again and the center one works. I'm puzzled as to why the dealership would tell me that a/thr door actuator failed on the diagnostic scan. Thanks for your help.
@TheBFHGarage
@TheBFHGarage Месяц назад
Sorry for the late reply I was out on a trail run. Hopefully you got it taken care of.
@jobvanluyken9466
@jobvanluyken9466 3 месяца назад
not tried this but maybe for the passenger side, removing the antenna completely first will get you access to the screws from that hole? Just a thought
@jasonronald3139
@jasonronald3139 7 месяцев назад
Hello. Great video, very detailed👍
@ninjaryder1st
@ninjaryder1st 2 месяца назад
Thank you so much for this! I just completed the easier driver side, but having difficulty replacing the plastic floor vent piece back into its place. Getting it out was also difficult as it was hard to get a firm grasp on it due to its location and everything else being in the way. Any tips for getting it to fit up inside and slide over the existing mounting spot since we cannot maneuver it very well?
@TheBFHGarage
@TheBFHGarage 2 месяца назад
Keep wiggling it until it snaps in place... Take a close look at how it goes together and that will help. Certainly a frustrating thing to do!
@ninjaryder1st
@ninjaryder1st 2 месяца назад
@@TheBFHGarage Thanks! Been messing w/ it for an hour, and cannot get the 1st piece/back half to align and slide over the existing plastic edges where it mounts. There is no rotational room and Im hitting the dash plastic while still needing it to move up/rearward by nearly 1/4 inch. Does it have more space by pushing it towards the centerline somehow?
@ninjaryder1st
@ninjaryder1st 2 месяца назад
@@TheBFHGarage haha, this is humbling. My wife, albiet with smaller hands, less frustration, and a basic understanding of the sandwiched space, basically replaced it within 2 minutes. She did it based on feel w/o much vision not even using a light. Behind every good man is a Great woman! I also removed the metal bar (two 8 mm bolts) supporting the lower dash plastic that was in the way.
@TheBFHGarage
@TheBFHGarage 2 месяца назад
@ninjaryder1st my hands are big and it gave me issues too!
@3vetman
@3vetman 9 месяцев назад
Excellent video Mike! Thank you so much. Would a flexible bit driver extension, like the ones that come with the powered screw drivers work for that back bolt? Mine's about 12 inches long. I always enjoy your videos and learn so much!
@TheBFHGarage
@TheBFHGarage 9 месяцев назад
I was actually considering getting one of those butt couldn't find one long enough. 12" won't even be close. By the time you add the bends needed I bet your looking at 24"-30".
@richwitt3559
@richwitt3559 9 месяцев назад
Would a dab of lithium grease be beneficial to lubricate the slot in the blend door arm to keep things moving easier?
@TheBFHGarage
@TheBFHGarage 9 месяцев назад
Yes I've seen people mention that and I don't think it would hurt. In my case there was still plenty of grease piled up on the part, so I just smeared it around
@kevinfromrhodeisland
@kevinfromrhodeisland 2 месяца назад
Of the two actuators on the passenger side, how do you know which one you should replace? Clicking is only coming from passenger side
@TheBFHGarage
@TheBFHGarage 2 месяца назад
Get your ear up close and see if it's coming from the middle or the far right
@lylekliewer4787
@lylekliewer4787 5 месяцев назад
At about 10:45 on the video accessing the driver's side actuator, that vertical support can be unbolted at top and bottom. Access is easier but still not all that great. That duct is a real pill. The last person to have been in there just kind of laid the duct in there and didn't fasten it to the plenum. No wonder my daughter complained of not getting heat on her feet!
@themtzionlion
@themtzionlion 2 месяца назад
Thanks
@joerouth6255
@joerouth6255 Месяц назад
It’s easy enough just to un plug outside air blend door and leave it on cabin recirculation. I just crack the window if I need outside air
@jeepguy1337
@jeepguy1337 7 месяцев назад
I don’t have the clicking on my 2013 wrangler but I have zero heat. Flushed the heater core 3 times without any luck. I also changed the blend door on the drivers side, any ideas?
@TheBFHGarage
@TheBFHGarage 7 месяцев назад
It could be a number of things. I would get on the JK forums and have people help you troubleshoot.
@gregbuckley1791
@gregbuckley1791 7 месяцев назад
I cussed way more than you did, lol. I own a car dealership and mechanic shop. Pneumatic 1/4 air ratchet from Harbor Freight fit right in. Remove the front screw that you can see and knock the blend door out with a pry bar. Easiest way to get to the back one since it'll be visible.
@cigarfactory74
@cigarfactory74 7 месяцев назад
Hi Mike, sorry if this is not the best video for my comment. My jku (2016) has air flow issues - when I change from panel flow to floor or floor/panel mix - limited air comes out or no air at all unless I turn the knob back and forth from panel to def etc. Sometimes this is accompanied by a funny smell. Does this sound like I have an Actuator failure? (I still have both cold and hot air, just a flow problem)
@cigarfactory74
@cigarfactory74 7 месяцев назад
(Also - i am not having any kind of ticking noises, only the air-flow problem)
@TheBFHGarage
@TheBFHGarage 7 месяцев назад
It could be. Hard to say. Does the smell come from one side vs. the other or can you tell?
@shanevanorder2644
@shanevanorder2644 4 месяца назад
Wish mine was ticking but its more of a hiss
@chrisdavis3444
@chrisdavis3444 5 месяцев назад
You need to specify better there is a mode door on passenger side for changing where the air flows. Blend door is cold to hot…
@ChadGatling
@ChadGatling 5 месяцев назад
Got a white Ashy Larry
@dclangst
@dclangst 8 месяцев назад
Right angle screwdriver might help.
@TheBFHGarage
@TheBFHGarage 8 месяцев назад
Nowhere near enough room
@deanothornhill9424
@deanothornhill9424 7 месяцев назад
This was a bitch !!! Thxz Mike saved me the $$$
Далее
Here's Why I Hate Jeeps
10:03
Просмотров 231 тыс.
How to Reset a Ford Blend Door Actuator
5:43
Просмотров 167 тыс.
JK Recirculation door actuator
9:37
Просмотров 49 тыс.