No video :(

How To Replace a Stylus Lamp (TECHNICS 1210-1200) with LED dj MOD

Подписаться 354

Просмотров 67 тыс.

50% 1

- How To Replace a Stylus Lamp (TECHNICS 1210-1200) with LED dj MOD
-------------------
Guida Per Cambiare la lampada stylo Originale con la Modifica a Led
-------------------
For buy this kit search on ebay: TECHNICS Stylus DJ LED MOD
or search this Seller: Hitech-zone
Per Comprare questo kit cerca su ebay: TECHNICS Stylus DJ LED MOD
O cerca questo venditore: Hitech-zone
___________________
Questo kit e migliore rispetto alle altre soluzione proposte dal web perchè:
-Non utilizza transistor (come stabilizzatori di tensione) che si surriscaldano, consumano energia inutilmente e con il tempo posso rompersi e andare in corto circuito! con la possibilità di danneggiare il piatto stesso.
-E' facile da montare
-Utilizza ben 3 led

Опубликовано:

28 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 12

@rsanchez7111 10 лет назад

At Ricardo Romero hey mate don't worry they can be fix. I did the same thing. I had a broken wire from the target light and the wire was loose an I got a short. Any way I replaced Q2and Q3 check the fuse. There is a couple of thing that went wrong. Btw I just replaced all the led s the pitch the strobe the 33 and 45 and the target light and new audio RCA s it took me 6 hrs per TT. I am doing this to my other 4 TT. I have 6 of them. I spent a good amount of hours on you tube watching vids on how to do so. But when you guys do this make sure follow the instructions cause each kit is different. Don't forget the led lights they have a + and - they have to go in the right place. The positive is the one with the longer leg. Or wire. In most cases you have to cut them to length before you cut them make sure you mark ider one + or - so you know what is what. Read instructions so you don't mess stuff up. I knew nothing about that. . But I wath a lot of vids and it's a lot easier for me now. When you change the target led use the resistor that comes with. Do not use the old one it's not for tha new led. If you try to save time. You will regret it. Good luck!

@solovenezuela4736 7 лет назад

Good, help my friend Mk2 not turn on the power supply board is correct because the other mount another mk2 and it worked perfectly, where I can start looking for the fault help me is you're a Crack in this topic Thank you

@Skuppo 14 лет назад

Grande Kommando!!!!!

@BIGSABMUSIC 11 лет назад

so where did you buy your led bulb and how come you didnt connect a resistor and voltage regulator to it ?

@johnnysmile01 2 года назад

where's the link to get the kit ? i want a green led.

@874djricky 13 лет назад

MAN I DID THIS AND THAT BURN MY TURNTABLES.

@rsanchez7111 4 года назад

Ricardo Romero it happened to me by accident. I got it fix. Part Q2. I had a loose wire from the target lamp and shorted Doing some research I test them Q2 part using a multimeter and sure enough part was faulty. When I got the new one I compared the reading and sure enough it was different. I assumed that had to be the problem. Lucky me. That was it. Did you fixed your turntable?? It happened to me 3 years ago. There was enough information on RU-vid. That’s how I got some help.

@djevilj66 4 года назад

do not do this to your turntable!! you WILL burn it up over time.. you can mod the cue light w/ led's but make sure u use proper resistors and possibly a voltage regulator(for some models)

@KommandoTubex 13 лет назад

@874djricky shit! do not do these things if you're not an expert!, and where did you find this kit? you built it yourself?