How To Replace Engine Mount 03-06 Mazda 6

Подписаться 67 тыс.

Просмотров 34 тыс.

50% 1

Hey guys here with a very simple DIY job on the 2003-2009 Mazda 3. Showing you how to replace the all engine mounts
Engine Mount Set:amzn.to/3rEDCzB
Deep Impact Socket Set:amzn.to/3ysvR3l
3/8" deep socket:amzn.to/3T2GB08
Ring Spanner Extra Long:amzn.to/3ecN7mB
Ratchet Set:amzn.to/3fHRq9B
Mazda 6 oil filter:amzn.to/3SYeTSq
*Disclaimer
We are not responsible for property damage or injury incurred as a result of any of the information contained in this video. Information given in this video does not guarantee the desired outcome. Any injury, damage or loss that may result from improper use of the tools, equipment, or the information contained in this video is the sole responsibility of the user and not carfix

Опубликовано:

9 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 26

@pavko879 Год назад

Great job! All 3 mount in one video. Very short and clear

@donutman3089 Год назад

Great video. Quick and to the point.

@stevensanchez6412 Год назад

Thanks for the info 👍

@Pinkielover 2 года назад

always support motor , when doing the mounts... Especially the top mounts.. I would've replaced the top mounts first including the tranny mount

@raymondboots6089 2 года назад

Great video, good job! Than you for a great video share! Have a great one!

@natemcbeth6423 Год назад

My 2006 Mazda6s 3.0L automatic has the exhaust getting in the way of pulling the bolts for the torque mount. Any recommendations?

@HewaBaxtyar1986 Год назад

Thanks

@csucsok82 2 года назад

What is the mount brand name? That car was benzine or disel?

@maksim9863 Год назад

Does manual and automatic mazda 6 have same dog bone mount? Or different part number?

@carfix1993 Год назад

I'm think same dog 🐕 mount

@theprodistini2590 3 месяца назад

Same. Recently did mine.

@willo6701 6 месяцев назад

It did not show that you have to put support for the engine when taking off the mounts so you keep the engine on place

@esevato23 Год назад

What sizes and tools did you use?

@heribertopena9832 Год назад

Reyena el círculo del soporte con Silicon bueno y listo

@pinktr_ee 2 месяца назад

why didmt you show yourself putting support for thr engine ?

@esevato23 Год назад

Part number for driver side mount

@reemarteen4813 Год назад

How much do you torque

@MrMairtin Год назад

How did you support the engine from below? Do you have a picture of it?

@carfix1993 Год назад

Put trolley jack

@MrMairtin Год назад

@@carfix1993 Ok. But where is the lifting point?

@peaceinhands2714 6 месяцев назад

Where is u r garrage located?

@carfix1993 6 месяцев назад

Epping

@luken6639 4 месяца назад

You did not use a torque wrench. A big no no.

@mariog.5671 2 года назад

How did you avoid the motor movement? did you use any other tool and how?

@carfix1993 2 года назад

Use troll jack for underneath

@luken6639 4 месяца назад

Use a trolley jack with 4x4 timber, Once mount is off you can move motor by hand with trolley jack underneath carefully to line up if needed. Jack it up a little on corner of sump making sure its balanced and stable before removing top mount. Torque settings are as follows body of engine 3 bolts up to 50 ft lbs. 3 bolts on top plate 72 ft lbs.