How to Replace Front Control Arm and Bushings 05-10 Pontiac G6 Saturn Aura

1A Auto: Repair Tips & Secrets Only Mechanics Know

Подписаться 2,5 млн

Просмотров 264 тыс.

50% 1

Buy Now!
New Control Arm with Ball Joint Set from 1AAuto.com 1aau.to/ia/1ASF...
1A Auto shows you how to repair, install, fix, change or replace a broken, busted, bad, loose, or damaged tie rod. This video is applicable to the Pontiac G6 and Saturn Aura, model years 05, 06, 07, 08, 09, and 10.
This process should be similar on the following vehicles:
2005 Pontiac G6
2006 Pontiac G6
2007 Pontiac G6
2008 Pontiac G6
2009 Pontiac G6
2010 Pontiac G6
🔧 List of tools used:
• Pry Bar 1aau.to/omK/1AX...
• 15mm Wrench 1aau.to/onr/1AX...
• 18mm Wrench
• 15mm Socket 1aau.to/oPV/1AX...
• 18mm Socket 1aau.to/otr/1AX...
• A Piece of Pipe (for leverage)
• Ratchet 1aau.to/oTS/1AX...
• Torque Wrench 1aau.to/ozY/1AX...
• Floor Jack 1aau.to/oo3/1AX...
• Jack Stands 1aau.to/onF/1AX...
Subscribe: / @1aauto
Check out our playlist:
Pontiac G6 2005-2010 1st Generation: • Pontiac G6 2005-2010 1...
Chevy Auto Repair Videos: • Chevy Auto Repair Videos
For More Info visit us at 1aau.to/h/aaa/
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

Авто/Мото

Опубликовано:

28 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 104

@1AAuto 3 года назад

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto √ *Do it Yourself* √ *Save Money*

@tonysiliguri 7 лет назад

Great video but your description should note on the G6 it is the 4cyl model being demonstrated and advise all v6s have front bolt motor mount clearance issues that require extra time and attention. Major omission!

@TopNotchChampion 3 года назад

For those with this issue, I just did mine. Need to lift transmission on driver side, and engine on passenger side. When replacing new control arm, ball joint first, then front bushing then rear bushing worked the best. I also needed to remove the rear bushing and slide in to place first for easier installation.

@Bags1818 7 лет назад

1aauto videos got me into wrenching, you guys explain and show everything In a very clear and practical way that make you feel confident you can get the job done yourself . Keep up the great videos!

@1AAuto 7 лет назад

+Ryan b Thanks for watching. If any of our viewers needs to make this repair, we carry the auto repair part shown in this video on our website. Here is a link to them www.1aauto.com/1A/front-control-arms/Pontiac/G6/1ASFK00182?RU-vid&CTA+Comment&QxxUcXRLo

@dcents5458 7 лет назад

Thanks guys...awesome video! Note: Saturn Aura 3.5 V6 is not as easy as this video with the 4 cyl, you have motor mounts in the way that will have to be move slightly out of the way to do the job....so not as easy as the job in this video

@1AAuto 7 лет назад

+D Cents Thanks for watching. If any of our viewers needs to make this repair, we carry the auto repair part shown in this video on our website. Here is a link to them www.1aauto.com/1A/front-control-arms/Pontiac/G6/1ASFK00182?RU-vid&CTA+Comment&QxxUcXRLo

@mattmgarza 4 года назад

I appreciate 1A Auto's videos. Any time I have a repair and I see that you guys have made a video on it, I know it's gonna be smooth sailing--or as smooth as the job will allow, lol. Thank you!

@1AAuto 4 года назад

+Matt Garza Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1AAuto.com

@evanpost6108 2 года назад

Awesome, clear and brief, love it. Thanks for keeping it under 10 minutes and giving clear shots. The only snag I ran into was the front bolt in the control arm did not come out all the way with my hands because a motor mount was in the way. But I was able to use a pry bar to pry on the bolt head and it came right out.

@1AAuto 2 года назад

+Evan Post Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c

@austinwartick4345 Год назад

How did you fit the pry bar in there? I really dont want to take motor mount out

@edwardmmanns7454 Год назад

Great video... thanks for all the speeding up.

@bustdnkl7507 10 лет назад

The Aura with a LZ4 V6 requires that the engine mounts be moved before you can take out the front bolt. Much fun.

@rickreimer 7 лет назад

This only works for some G6 models. My 2007 3.5L required unbolting the engine mount and raising/lowering the car to get the main bolt out.

@shoe2241 3 года назад

my g 6 had the mount in the way. major pain in the butt to change the control arm. its a 2007.

@edwardx4979 7 лет назад

This is the same procedure for a 2009 Chevy Malibu. Good job, guys! Just a suggestion, but you guys should include the name of other cars that this tech repair can relate to. Thanks for the video

@1AAuto 7 лет назад

+Edward X Thank you for watching, and the insight on vehicle repair list! 1aauto.com

@edwardx4979 7 лет назад

For a 2009 Chevy Malibu LT, the only difference is that the two bolts on the bushing is positioned differently on the arm bar...that's all. Hope this comment helps you guys who are looking to change a 2008-12 Chevy Malibu. I'm not sure but it might be the same for the 2013-15 too if GM didn't change the control arm. PLEASE check before you repair

@FreshKicks4545 6 лет назад

Edward X thanks I will be ordering from 1A auto ,and do it my self

@DJMovit 6 лет назад

While my Saturn Vue is a little different this video helped get the rear bushing out.

@jameldixon4140 6 лет назад

Hello, DJMovit. My son's friend also has a Saturn vue (2009) that needs a new control arm. I was wondering, did you have to replace the whole control arm, too?

@keacehicks7171 2 года назад

Make sure it’s leveled before tightening?

@chriswhereyouat 6 лет назад

Great video, I will be placing my order for many parts for my 09 Malibu because of this. Thanks again

@joevillanueva1514 7 лет назад

the motor mount is in the middle of the bolt? how to take it out not all Pontiacs are the same it's the same model and everything except the amount is in the middle of that Bolt

@brassmonkey4506 6 лет назад

One thing they need to mention is that for these vehicles with the 3500/3900 V6 you will need to support the motor and remove the motor mount in order to remove the front control arm bolt.

@BIGROYTHEDON 6 лет назад

Man i wish i read this comment 5 hours ago

@IlliterateSage 5 лет назад

Oh damn. I was hoping to replace my front control arms soon. Thanks for the note! I might have to take it in, then.

@jamimcdonald3859 4 года назад

Yup like to kick engineer some where for the v6 model

@eavery8 2 года назад

And passenger side the exhaust pipe is in the way.

@ultimateormus7903 2 года назад

Good work

@maxlove4821 6 лет назад

Very well explained I like all ya videos You guys don't talk all that bullshit that no one likes to hear you get straight to it good job guys 👍👍👍👍👍👍👍👍👍👍👍👍👍👏👏👏👏👏👏👏🤙🤙🤙🤙🤙🤙🤙🤝🤝🤝🤝

@edwallchris84 7 лет назад

Very helpful. thank you. just a quick note, you called the ball joint a tie rod.

@1AAuto 11 лет назад

Yes you would need an alignment after this procedure. 1aauto.com 888-844-3393

@user-gw1pu4io8x Год назад

Great video, but it is not the same for all G6. If you can check, the G6 GXP is a bit different, and the back bolt does not come out that easy. I just wish you guys would make a video on how to do it on a G6 GXP and also how to replace the bushings on the swaybar, not the sway bar link that's easy. Thanks for all your videos

@1AAuto Год назад

+Raul Santos We're always cycling through common cars. We'll add this repair to our list! 1aau.to/m/Shop-1AAuto-c

@Frost_Tiger 7 лет назад

Would you use grease in the control arm bushing or just put it in without using grease

@ryanbasser9396 6 лет назад

You don't have to remove the motor mount you just have to loosen top and bottom nuts and pry up on mount and the bolt will slide in and out easier then getting the mount out

@xiiixlllvlllxiiix 5 лет назад

Ryan Basser be more specific man

@sanyex8390 7 лет назад

Thanks this will help me with my Opel Vectra C !(apparently this 2 car use the same control arm)

@ramram981 7 лет назад

Hello, thank you very much for so many great videos! Can you tell me why you don't remove so many of the nuts or bolts with the impact wrench in this video?

@adammcintee4439 Год назад

My ball joint bolt snapped and the stud is stuck ( rusted and more corroded ) in knuckle any tips on how to get it out ? Hammer and punch ? Maybe with torch ?

@takeoUup115 3 года назад

08 g6 , passenger side you have to unbolt motor mount and lift motor to get the front bolt out .

@NOBOX7 11 лет назад

no alignment?

@1AAuto 11 лет назад

It could be. You may also want to check the front axles and all of the suspension pieces such as the tie rod ends and steering stabilizer end links to see if they are worn. 1aauto.com 888-844-3393

@MarquisVonLion 6 лет назад

Hello, I've got a Pontiac vibe 2008, I need to replace the lower control arm ( left side), so far I managed to remove it, but I'm having difficulties to install the new one ( the original one was bent in a car crash :

@Bubblebag2010 7 лет назад

This is not the same for a 2006 g6. the motor mount is in the way to pull the forward bolt out.

@deathk26 7 лет назад

The V6 setups have the motor mount that is in the way. All you should need to do is remove the bolts underneath for the mount and jack the engine up to get clearance.

@kimjuanun4873 5 лет назад

It is the same, i changed my front 2 last summer

@kimjuanun4873 5 лет назад

I have a 2.4, 4 cylinder though

@mamdouhnoshy7020 5 лет назад

Please what do you mean by the front bolt 70 f/p Thank you

@1AAuto 5 лет назад

+Mamdouh Noshy 70 foot pounds of pressure. You will need to use a torque wrench in order to ensure this is tightened to spec.

@clmcls 10 лет назад

My car makes a cracking sound when I turn the handle to the left or to the right. Is something wrong with my control arm?

@1AAuto 10 лет назад

You may want to inspect the ball joints and all of the front suspension and steering pieces.

@user-gw1pu4io8x Год назад

This video is great, but it does not work on all G6. It is definitely not how it goes on the G6 GXP the motor mount is on the way to remove the bolt.

@dragonprototype3883 6 лет назад

What to torque the front bolt. The bolt you loosened after the tie rod bolt came out ?

@koreymayo8884 4 года назад

Why don't you use an impact wrench?

@cheyward1660 7 лет назад

Did urs come with a grease valve for bushings?

@mamdouhnoshy7020 5 лет назад

Thank you kindly, but I was just asking for what you mean by the front bolt. (70-foot-pounds)

@vincentlockie2510 4 года назад

Mamdouh Noshy it’s the bolt that is straight across from the ball joint, tighten that to 70fp

@mikeswede13 11 лет назад

Would this also work for my 2005 malibu?

@rlm102466 5 лет назад

Your video states Bushing replacement.... none showed here.

@th3elf 3 года назад

The bushing is part of the control arm

@clmcls 11 лет назад

do you guys have a shield replacement for the fuel tank?

@codys3915 8 лет назад

I would like to do this to my 2006 Pontiac G6 3.5L sedan...will I need to remove the engine mount on that particular model for the passenger side control arm??

@doofapotamus2323 8 лет назад

I had a similar problem on my '08 3.5. I placed the jack underneath the motor and removed the rubber mount and it was fairly easy to do.

@ryanmoore4098 7 лет назад

This does NOT apply to a 2007 Saturn Aura. In the Aura the engine mounts must be removed in order to back the front bolts out.

@jayryan7473 6 лет назад

It does apply to the 2007 Saturn Aura as long as it is a 4 cylinder. The V6 requires removal of the motor mount.

@bdubberz 5 лет назад

If we have a bad ball joint is there any way to just replace that?

@1AAuto 5 лет назад

+Brandon Woychik Thanks for checking us out! Depending on the vehicle, ball joints are typically replaceable rather than the whole control arm. 1aauto.com

@crystalh5148 8 лет назад

great vid...thanks man

@1AAuto 8 лет назад

+Crystal Fusco No problem. Thank you for watching. 1aauto.com 866-403-3393

@watuzi 11 лет назад

Thanks for this video. If my Nissan Quest makes thumping noise on bumps, could it be worn control arm bushings?

@vincentlockie2510 4 года назад

Edmund Mendez definitely a tie rod end.

@aaronglbrn 10 лет назад

the ball joint doesn't go in except for just the tip when install the new one..on my 09 chevy malibu. the store said i dont have to press it... any advice?

@1AAuto 10 лет назад

If you can get a nut threaded onto the tip (by hand), it should suck the control arm up into position when you tighten it down.

@jericho7899 6 лет назад

How similar is the process for the drivers side?

@1AAuto 6 лет назад

+jericho kendall It should be the same or a very similar process. We also carry the new control arm shown in this video on our website. Here is a link to them. We hope that this helps you out. www.1aauto.com/1A/front-control-arms/Pontiac/G6/1ASFK00182?RU-vid&CTA+Comment&QxxUcXRLo

@BillyMoonMan 7 лет назад

what would be the process if I just wanted to change the bushing? is that possible with this control arm? I can't find any info on it at all

@1AAuto 7 лет назад

+Billy Moon Thank you for checking us out. In most applications, the bushings should be able to be pressed out, however we do not have a video available at this time. You would need a bushing press tool or similar, but we recommend verifying the exact procedure through a service manual. 1aauto.com

@lavishluevano 7 лет назад

do I need an alignment after this?

@1AAuto 7 лет назад

+lavishluevano Yes you will want to get an alignment performed after replacing these parts. 1aauto.com

@mtb16507 10 лет назад

thanks great video

@1AAuto 10 лет назад

Thank you for watching! 1aauto.com 888-844-3393

@ignatiusreilly8280 3 месяца назад

And not shown: "kinda jack up the mount so geometry is right" - I need to see that, I don't know what I'm doing :/

@shawnjohnson1058 6 лет назад

What do you mean jack the suspension up?

@1AAuto 6 лет назад

+Shawn Johnson You will have jack up the suspension but putting the jack under the lower ball joint. Jack up the suspension just until the vehicle comes of the jack stand you were using while doing the rest of the steps. One the nut it tightened you can lower the car back onto the jack stand. 1aauto.com

@jayryan7473 6 лет назад

Nope! This isn't for any ol' G6. This has got to be the 4 cyl you're working on. Add an extra hour labor if you need to do this on the V6, which has clearance issues where you need to remove the engine mount. These guys have it figured out: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-D-SoyYCz0qw.html

@Frost_Tiger 6 лет назад

can you press out the control arm bushings or the whole bushing will have to be replace?

@1AAuto 6 лет назад

+Aaron Nelson You can press them out, but is is easier to replace the whole thing.

@Frost_Tiger 6 лет назад

1A Auto Parts thanks makes my job easier then

@compitacris 7 лет назад

I have an 05 malibu. Will this be the same procedure

@1AAuto 7 лет назад

+compitacris Thank you for checking us out. The procedure should remain the same as long as you have the new body style Malibu. www.1aauto.com/1A/front-control-arms/Pontiac/G6/1ASFK00182?RU-vid&CTA+Comment&QxxUcXRLo

@compitacris 7 лет назад

1A Auto Parts thank you guys. It's actually a malibu maxx

@1AAuto 7 лет назад

+compitacris Thank you for the response. The Malibu Maxx will still remain the same procedure. Please let us know if you have any further questions. 1aauto.com

@Banism24 7 лет назад

good

@1AAuto 7 лет назад

+Banism24 Thanks for watching. If any of our viewers needs to make this repair, we carry the auto repair part shown in this video on our website. Here is a link to them www.1aauto.com/1A/front-control-arms/Pontiac/G6/1ASFK00182?RU-vid&CTA+Comment&QxxUcXRLo

@mikelboyd711 4 года назад

That wasn't the tie rod.. that was the ball joint..

@davidhinkle2207 2 года назад

That is NOT the same as a 2009 Saturn Aura

@markjensen1927 10 лет назад

No alignment necessary for lower control arm replacement on this vehicle or the malibu, aura.

@1AAuto 10 лет назад

You should get the vehicle aligned after replacing the control arm. 1aauto.com 888-844-3393

@nopaper9592 4 года назад

Cant believe they want 1200$ for this

@kainhall 5 лет назад

Our saftey lady told us to not use a "cheater pipe" I told her "then how do I do my job?" Like seriously....

@josephfine3394 5 лет назад

NEVER use a cheater bar on a ratchet wrench! Use a long breaker bar to break bolts loose, or you could strip your ratchet pawls and injure yourself. This damage is not covered under warranty, either.