How to replace motor and remove transmission slipper gear off Arrma Granite Senton Typhon

Подписаться 4 тыс.

Просмотров 12 тыс.

50% 1

Other Recommendations:
Mighty Gripper Black
MyLaps RC4 Hybrid AIT10R078
AKA CA Glue
Hobbywig Electronics
Tekin
Castle Creations
Team Powers
Gens Ace
Gorilla Tape
JConcepts CA Glue
MIP Tools (Drivers)
Kobalt Pliers
Craftsman Pliers
Craftsman wrench
Tamiya Paint (PS-X)
Duratrax Paint by Horizon Hobbies
Savox Servo
Team Powers Servo
Traxxas Servo (for non-demanding applications)
Proline Bodies
Proline Tires
JConcepts Bodies
DE Wheels
WD-40
Yokomo Touring Tires
Team Powers Touring Tires
Dremel 4000

Опубликовано:

25 ноя 2022

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 37

@marvin86047 6 месяцев назад

Thank you for this, great explanation and camera work, now i can replace my burnt out motor without the anxiety.

@telecomandorc 6 месяцев назад

My pleasure. 🤝

@teadeez69 Год назад

The best tutorial I've seen the way you explain things is awesome. 👍

@telecomandorc Год назад

Thank you kindly. 🤝

@coolbluefoxeverything 8 месяцев назад

Thank you so much I needed a tutorial to replace my broken motor on my Arma Typhon

@coolbluefoxeverything 8 месяцев назад

This tutorial helps you replace the mass majority of the Arma vehicles because they all are the same.

@telecomandorc 6 месяцев назад

My pleasure, I am glad it helped.

@VidhiSwami 6 месяцев назад

Very informative

@telecomandorc 6 месяцев назад

Thank you.

@islandrc-duke1972 Год назад

cool how to video,have a great weekend brother

@telecomandorc Год назад

Thanks, you as well.

@vketil 5 месяцев назад

helps alot

@telecomandorc 5 месяцев назад

I'm glad it does. 🤝

@rccarsarefun Год назад

THANK YOU SO MUCH

@telecomandorc Год назад

My pleasure. 🤝

@GhostRider-ii7tz Год назад

Dewalt makes a driver.it has a gyro in it with a clutch.you can set

@telecomandorc Год назад

Awesome. Thanks for the lead. Have you used either the DCF682N1 or DCF680N1?

@GhostRider-ii7tz Год назад

@@telecomandorc mine is the dcf680n1.I love it.charges quick.the clutch works great.never strip anything.or over tighten

@telecomandorc Год назад

@@GhostRider-ii7tz Perfect. I have a Ryobi. Not bad as they say, you get what you pay for. It is great for $40 for reading the features on the DeWalt, it is worth spending the extra amount.

@chaceurbanski Год назад

I am having issues pulling it out. It won't budge I have yanked on the thing for about an hour.

@telecomandorc Год назад

Did you remove the screw in the bottom?

@chaceurbanski Год назад

@@telecomandorc yes

@telecomandorc Год назад

@@chaceurbanski If you removed the bottom screw and the red plastic block used as a stop and battery tie holder next the the shaft in front of the transmission, it should just slide out. Do not pull on just the tab. You need to pull on the ends too.

@JStoneFPV Год назад

@@chaceurbanski Did you get it removed? I'm in the same boat... removed the screw and can't get the battery/shaft protector to budge...

@alexandrehetu7466 Год назад

@@JStoneFPV pull hard and maybe use something to lever on the motor but make sure to hold the motor so you don't move it

@thefreedommemer 3 месяца назад

I have an issue: I cannot move the transmission piece out because sand has gotten inside of my RC car. I thought that driving my car on the beach was a good idea.

@telecomandorc 3 месяца назад

Tough to get sand out. Air compressor might be your best bet or a small flat head driver.

@thefreedommemer 3 месяца назад

@@telecomandorc Been using a pick kit, worked well, but a vacuum and a toothbrush is just a two hit combo!

@telecomandorc 3 месяца назад

@@thefreedommemer Good points.

@chummlysrc654 Год назад

hey how come you don't race buggies at nor cal

@telecomandorc Год назад

I used to. I have a few videos. But I cannot make it in time on Fridays due to my new job since then. That is why I have been doing mostly on road. Hopefully I will get some off road track time this winter.

@chummlysrc654 Год назад

i was there this weekend I'll be their next weekend as well hope to meet you

@telecomandorc Год назад

@@chummlysrc654 I probably won't make it until after on road ends. And I will definitely not participate on the 18th since that is the World Cup Final. That is a whole family event. But when I do, I am a weird looking guy with a burgundy buggy with three white circles. Do you drive 4wd buggy by any chance?

@williamoleary9330 6 месяцев назад

“tricky part”?? It’s dam near impossible to lift up that stupid tab while trying to push it into place and line up the gearing. I mean just dumb engineering

@telecomandorc 6 месяцев назад

Good point. They could have engineered it simple by just adding 4 screws to hold it down or something simple but still strong.