No video :(

How To Replace Power Steering Pump 2008-2017 Buick Enclave

Подписаться 491 тыс.

Просмотров 96 тыс.

50% 1

Buy Now!
New Power Steering Pump from 1AAuto.com 1aau.to/ia/1ASP...
Harder steering, squealing, or leaks are signs you might need to replace the power steering pump in your car or truck. This video shows you how to install a new power steering pump in your 2008-17 Buick Enclave.
• Check here for more videos on the 2008-17 Buick Enclave: • Buick Enclave 1st Gene...
This process should be similar on the following vehicles:
2008 Buick Enclave
2009 Buick Enclave
2010 Buick Enclave
2011 Buick Enclave
2012 Buick Enclave
2013 Buick Enclave
2014 Buick Enclave
2015 Buick Enclave
2016 Buick Enclave
2017 Buick Enclave
Tools you will need:
• 10mm Wrench 1aau.to/odw/1AX...
• 10mm Socket 1aau.to/okf/1AX...
• 15mm Socket 1aau.to/oni/1AX...
• 22mm Socket 1aau.to/oaC/1AX...
• Serpentine Belt Tensioner Tool 1aau.to/ox/1AXA...
• Trim Tool Set 1aau.to/odV/1AX...
• Hose Clamp Pliers 1aau.to/oJ/1AXA...
• 1/2 Inch Air Impact Gun 1aau.to/oaK/1AX...
• Ratchet 1aau.to/oop/1AX...
• Socket Driver
• Socket Extensions 1aau.to/oni/1AX...
• Swivel
• Torque Wrench 1aau.to/ohL/1AX...
• Fluid Transfer Pump 1aau.to/od/1AXA...
• Power Steering Fluid
• Floor Jack 1aau.to/odN/1AX...
• Jack Stands 1aau.to/odv/1AX...
• Wheel Chocks
Subscribe: / @trq
Check out our playlist:
Buick Enclave 1st Generation 2008-17: • Buick Enclave 1st Gene...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

Опубликовано:

2 ноя 2020

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 49

@TRQ 3 года назад

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts √ *Do it Yourself* √ *Save Money*

@aaronchojnacki4891 3 года назад

I am deeply thankful for your video. My daughter was quoted $1800. at the Buick dealer to do this job on her ‘14 Enclave. I own a ‘12 Enclave. Many videos out there drop the engine down. I don’t have a lift and had to work on my garage floor with the car jacked up high. Without your video, I would have been lost. I followed it to the tee. The only part I varied from was that back bolt on the pump. I took it off reaching through the wheel well with a 3/8 ratchet with a short extension and a 15mm socket. Pump cost $216 with the pulley installed. Daughter’s gratitude priceless! Thanks guys!👍

@TRQ 3 года назад

+Aaron Chojnacki Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1aau.to/m/Shop-TRQ

@alexanderproefrock8721 3 года назад

Was yours a fwd or AWD?

@davidanderson9588 11 месяцев назад

The shop quoted me like $2k to do this. Thanks for the informative video. It's a definite life saver.

@iamwhatieat1 2 года назад

How do you stay so calm 😂 man I've worked in a few shops over the years and there would minimum ten swear words just trying to get the heat shield off

@jeronimosantos2632 3 года назад

Thank you sir, I have been pondering on this job for a while because my concern was always dropping the subframe, I am a DIYer and I did not want to do that. With this video no reason to drop any subframe. I pulled out the power-steering pump as in the video, simple.

@TRQ 3 года назад

+Jeronimo Santos Thanks for watching our video! 1aau.to/m/Shop-TRQ

@grahamslamcardbreaks2172 2 года назад

im glad i watched this, i almost thought about trying it lol

@thachn1 2 года назад

this very help full I watch this video and replace the pump 1-1/2 hrs thank for info

@lmagee212 2 года назад

Best video out of all I've seen to remove/replace this pump.!

@TRQ 2 года назад

+lmagee212 Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1aau.to/m/Shop-TRQ

@jaredsales3364 Год назад

Just did this pump on my 2015 Traverse. My plan was to go this route of going over the exhaust with the pump rather than dropping sub frame. Ran into some frustrations, as well I purchased the new pump without the pulley and fitting, they had to be transferred from the old pump. It cuts about 30-40% of the part cost by purchasing the one without pulley and fitting. Then after removing lines, unbolting the pump… position the pump pulley slightly down and to the rear of the vehicle so that it is facing the opening between the inner fender and a-arm mount. Remove the pulley with puller (factory pulley has a groove around the hub on the outside of the pulley for a puller, you do not have to get behind the pulley at all)… both come out no problem separately through the opening above the A-arm mount. Position new pump in same spot, use install tool to install pulley… bolt it in place, attach lines. About 1/3 the time to re and re this way then going up and over the exhaust and a lot less then dropping the sub frame along with not dealing with that mess. Takes longer to remove the wheel and tie rod then the pump itself.

@Mysticlyonenterprise Год назад

Thanks for the tips.doing this task this morning.

@blaszilla90 Год назад

Great video. Where is the power steering fluid filter located? Going to replace my power steering pump and thinking I should replace the filter as well but don’t know where it is.

@scottlehman6587 6 месяцев назад

Great video thank you!! Scott from Hibdons!

@JavierDIYFix 3 года назад

Now its my turn to replace the steering wheel pump on my traverse 2014.. well done!!!👌

@TRQ 3 года назад

+Javier Romero Thanks for watching our video! 1aau.to/m/Shop-TRQ

@bjlofton9180 4 дня назад

Would this work on a 2013 Buick lacrosse?

@billstares1084 3 месяца назад

Thanks for video very helpfull

@chrisbauer1144 2 года назад

Great video. Thanks for the tips.

@downhillindad7689 2 года назад

This is by far the best video I’ve seen on this but still worried this is outside my wheel house. Having to do this on the ground instead of a hydraulic lift makes it feel like it’ll be a lot harder that in the video.

@TRQ 2 года назад

+Downhillin' Dad Thanks for watching our video! 1aau.to/m/Shop-TRQ

@shoDOHC Год назад

How'd it go? I'm debating on doing the job for a customer 🤔

@salvadorsepulveda6415 3 года назад

Seems like you get the tuff jobs !! Great job 👏

@TRQ 3 года назад

+Salvador Sepulveda Thanks for the feedback! 1aau.to/m/Shop-TRQ

@eliford3143 6 месяцев назад

Easiest way is to take off the hard line on the rack and pinion and with the pulley down pull it out between rack and motor

@pattywaktdiy4175 2 года назад

Excellent video. Working on a Traverse and could not remember how the o-ring was installed for the feed line to the pump (non-pressure). For some reason I can't install it without it leaking. At least now I know I am installing properly. I think I need to disconnect the hose as it is keeping it "cock-eyed" as I tighten the 10mm bolt. I'll remove the hose so the elbow is 100% free to line up square with the pump.

@kartboarder22g17 2 года назад

I changed my pressure hose, but now have a lot of whine noise for weeks. Level seems fine, but maybe I have air in there, I'm going to see if I can get it all out, not sure if that is the noise or the pump is now gone, any ideas?

@JohnWick-dj6lt 8 месяцев назад

Will it work for my 2010 buick lacrosse

@CRRC 2 года назад

thank very useful

@danielzizumbo3731 3 года назад

how did you get the pressure hose in? I've tried for a day trying to put the high press hose in.

@jimmielturpin88 Год назад

I had a friend that had her power steering pump fixed and they lost one of her bolts. Does anyone know the size of the mounting bolts on this

@omarargullin2313 2 года назад

Mine is front wheel drive do u think is the same precedure?

@mosesgeorgepattersonii8469 2 года назад

Hello, hey I have a 2012 Chevy Traverse LT trying to put the power steering pump on and I'm having the trouble that when I drop the subframe on the passenger side it's only going down two of the four in required to pull the power steering pump. Can you think of anything I could have done wrong?

@tonyc.8919 2 года назад

Need to drop the driver side also for more clearance

@shahinshahmohammadi8775 2 года назад

If I’m replacing the cv axle too can it come out the side like that?

@omarargullin2313 2 года назад

Do think is the same for a front wheel drive

@nisagin9544 Год назад

Hi Mr.TRQ I hope we can reach you I have problems same that your Buick 2010. Is leaking lots. I’m in Ontario Ca let me know thanks ❤

@TRQ Год назад

+Nisa Gin We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c