No video :(

How to Replace Rear Caliper 2006-12 Ford Fusion

Подписаться 502 тыс.

Просмотров 56 тыс.

50% 1

Buy Now!
New Brake Caliper from 1AAuto.com 1aau.to/ia/RABC...
A worn out or seized brake caliper can create dangerous and expensive problems: overheating, rotor and pad wear, or even total failure. TRQ brake calipers are engineered to fit your specific vehicle. This video shows you how to a rear brake caliper on your 2006-12 Ford Fusion.
• Check here for more videos on the 2006-2012 Ford Fusion: • Ford Fusion 2006-2012 ...
This process should be similar on the following vehicles:
2006 Ford Fusion
2007 Ford Fusion
2008 Ford Fusion
2009 Ford Fusion
2010 Ford Fusion
2011 Ford Fusion
2012 Ford Fusion
Tools you will need:
• Pocket Screwdriver
• Pry Bar 1aau.to/oa/1AXA...
• 10mm Socket 1aau.to/oa/1AXA...
• Hose Clamp Pliers 1aau.to/oa/1AXA...
• 3/8 Inch Air Impact Gun
• Ratchet 1aau.to/oa/1AXA...
• Socket Driver
• Torque Wrench 1aau.to/oa/1AXA...
• Brake Grease
• Liquid Thread Locker
• Drain Pan 1aau.to/oa/1AXA...
• Floor Jack 1aau.to/oa/1AXA...
• Hammer 1aau.to/oa/1AXA...
• Jack Stands 1aau.to/oa/1AXA...
• Wheel Chocks
Subscribe: / @trq
Check out our playlist:
Ford Fusion 2006-2012 1st Generation: • Ford Fusion 2006-2012 ...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

Опубликовано:

27 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 27

@TRQ 3 года назад

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts √ *Do it Yourself* √ *Save Money*

@bryhut17 2 года назад

Add in the sizes of the sockets used, and this would be perfect.

@sylvestergayekpar3699 2 года назад

Great video just wish u stated the socket sizes

@EvilSanta482 2 года назад

You really should use blue thread locker not red unless you really want to use a blowtorch to get it back out if you ever need to remove it again.

@danielgag8852 3 месяца назад

Excellent video. Helped me every step of the way.

@stevekennon1786 3 года назад

Great video...as is all of the TRQ videos. Please do a video on how to replace the starter for 06-12 Ford Fusion. Thanks !

@dmull515 2 года назад

These videos are so good. Great job!

@hoosiered471 2 года назад

Great video with detailed instructions!!!! Thanks!!!!

@stevekennon1786 3 года назад

Great video ! Please do one on how to replace the starter for 06-12 Ford Fusion. Thanks

@onewaynestreet 2 года назад

Thanks for the vid. I knocked out the job like a pro.

@kimbalmccoy4892 Год назад

The best video I have seen on how to remove and replace the parking brake cable on my Lincoln MKZ. Thanks!

@robertlandrum8598 Год назад

Great video !

@dillonsouriol1919 2 года назад

So you don't have to bleed the whole system if you Crack just one line 🤔 I

@martyforgigs 9 месяцев назад

You are the best!

@andrewhammer4375 11 месяцев назад

i'd be lost without you lol

@nateladd2157 Год назад

since the fusion and milan are the same car for the most part, will i be able to use this video for my 2010 mercury milan?

@randomcontenttv2118 10 месяцев назад

Can't get my e-brake bolt off my 2011 Ford fusion sel any suggestions

@larylhuntington5398 6 месяцев назад

Great video. Going to help a lot.

@markzgagowski6099 Год назад

Two questions. Did both of the rear calipers, rotors and pads along with front pads and rotors. Bled the rear calipers and breaks are squishy. They stop but don’t feel as firm as I thought they would be. I’d say 3/5ths of the way down for significant stopping. So I bled them again. This time i did the rear and front but when I went to get the nip off of the front it snapped the top off. What do I do now? I bled 3 out of the 4. I also did them rear right rear left tried front right and the. Front left. Stopping at about halfway down. Could it be that this is how firm the brakes are on 08 Milan? Ty😅

@eliselozzio2292 Год назад

Go get your vacuum pump checked out has to be down in shop.

@rodolfohuerta2303 Год назад

Better good class I am a mechanic now

@TheGb50 Год назад

You need dot 4 now on that car they have a recall on that car

@robertscott1156 11 месяцев назад

Not red thread locker. Blue or orange.

@kennethelandry3804 Год назад

I can’t fined where it tells you what wrenches to use , had to go to someone else

@armandhammer9617 2 года назад

So you totally skipped over the spring..

@shwiplashmac5390 4 месяца назад

Peetann. Thats amazing. I know thats not how its spelled but its how it sounds. Love it. Full accent of some sort just to infuriate someone, sonewhere.