No video :(

How To Replace Sonata Sway Bar Bushings

Подписаться 7 тыс.

Просмотров 7 тыс.

50% 1

Please support the channel by becoming a Patreon / bigwillcarcare
Disclaimer
This video is for reference only always refer to manufacturer instructions, advice and proper service manual for actual directions specifications and safe practices when working with tools and equipment. Due to uncontrollable factors Big Will's Car Care is NOT Liable for any misuse or improper usage of Products, Information, Mechanical Equipment, Electrical Equipment, Hand Tools,Power Tools, Ramps, Jacks, Jack Stands, Cleaners, Grease, property damage, injuries, loss or damage that may result from any inappropriate and or improper use of this video and tools

Опубликовано:

28 мар 2023

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 19

@majhoolmaroof2065 5 месяцев назад

I have nothing but gratitude for you. THANK YOU!

@BIGWILLSCARCARE 4 месяца назад

You're very welcome! Thanks for watching please Like, Share and Subscribe if you haven't already

@KwispyKweef 8 месяцев назад

I own a 2007 Sonata and I have been terrified about getting to my sway bar bushings, and you just made it look so easy. Fears are gone and I know I can do it now lol

@BIGWILLSCARCARE 8 месяцев назад

Glad it helped. Thanks for watching please Like, Share and Subscribe if you haven't already

@surgeneral108 2 месяца назад

Great job ...much needed

@BIGWILLSCARCARE 2 месяца назад

Thanks for watching please Like, Share and Subscribe if you haven't already

@stevephilibert 4 месяца назад

I just changed the bushings on a 2006 and after spending and over 2 hours getting the bolts out in the tight space from below, I realized is could use about 24” of 3/8 extensions and reach straight down front the top by the firewall to the bolts. If I would started knowing this it probably would have taken about less than an hour total to do them.

@kevinftw16 2 месяца назад

V6 or 4 cylinder? Should be the same but with the bigger engine just wondering if there's still enough room to do it from the top.

@stevephilibert 2 месяца назад

@@kevinftw16 It was the 3.3 V6

@kevinftw16 2 месяца назад

@@stevephilibert Cool so I should be able to get it from the top then

@froztout Год назад

Well...Got my azz kicked today by those sway bar bushings!

@borg386 3 месяца назад

Hello from Florida USA. Can you tell me those cheaper links and bushings on Amazon and ebay are any good? Thanks for any answers!

@leonarddaye7550 Год назад

Thanks for the vid

@genericusername1365 Год назад

Will this be the same method for the previous generation Sonata (2006-2010)?

@BIGWILLSCARCARE Год назад

Yes it's is similar. Thanks for watching please Like, Share and Subscribe if you haven't already

@davida871 Год назад

My 2005 Optima is a bear to do these. The front 14mm bolt is slightly under inner tie rod boot. Any suggestions?

@BIGWILLSCARCARE 11 месяцев назад

In that case you have to disconnect the outer tie rod from the knuckle and move it out the way enough to get to the bolt. Thanks for watching please Like, Share and Subscribe if you haven't already

@rrsttt7505 Год назад

It’s not easier, but I’m replacing mine while I’m replacing the turbo. The entire subframe has to come out, and that makes it “easy” to get to, but getting the subframe out is a chore. Going to go ahead and replace the lower arms, tie rods, sway bar links, and the steering rack. I’m at 140k miles, I have it torn apart and to the point I can get to all of it, rather do it now than have it fail in the next 5 years and be doing it again.

@BIGWILLSCARCARE Год назад

@rrsttt7505 Thanks for watching please Like, Share and Subscribe if you haven't already