How to Replace the Rear Brake Pads and Rotors on a 2002 Ford F 350 Dually

Подписаться 217 тыс.

Просмотров 113 тыс.

50% 1

Brian Eslick from How to Automotive www.howtoautomo... takes you step-by-step through the process of replacing the rear brake pads and rotors on a 2002 Ford F 350 Dually.
Affiliate link mentioned in the video for Wagner Severe Duty SX757 Semi-Metallic Disc Pad Set, Rear amzn.to/2r1E1vB
Affiliate link mentioned in the video for Parts Master 125660 Rear Brake Rotor amzn.to/2rWkUDp
Affiliate link mentioned in the video for Permatex 24300 Surface Insensitive Threadlocker Blue, 0.34 oz. amzn.to/2r2Zbf0
Affiliate link mentioned in the video for AGS BK4 Brake Lubricant 4Oz amzn.to/2qprdNP
Website
For more videos, tips, and to purchase recommended tools and products visit my website at: www.howtoautomo...
Stay connected at:
Email: howtoautomotive@gmail.com
Facebook: www.facebook.c...
Google+: plus.google.co...
LinkedIn: / brian-eslick-819839118
Disclaimer
Owing to factors beyond the control of How to Automotive/Brian Eslick, it cannot guarantee against unauthorized modification of this information, or improper use of this information. How to Automotive/Brian Eslick assumes no liability for property damage or injury incurred as a result of any information contained in this video. How to Automotive/Brian Eslick recommends safe practice when working with power tools, automotive lifts, lifting tools, jacks and jack stands, electrical equipment, blunt instruments, chemical lubricants, or any other tools or equipment seen or implied in this video. Because of factors beyond the control of How to Automotive/Brian Eslick, no information contained in this video shall express or imply warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or information contained in this video is the sole responsibility of the user and not How to Automotive/Brain Eslick. #howtoautomotive

Опубликовано:

18 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 54

@randyhelgath685 7 лет назад

Excellent Video! One of the best, the steps and procedures were well thought out.

@HowtoAutomotive 7 лет назад

Randy Helgath thank you. And thank you for watching!

@larryeaton7384 3 года назад

Very good information! Save yourself a pain by pumping your brake pedal before you put the tires back on. This way you can see the calipers in action and take out any guess work!

@jameschimino8757 3 года назад

Well done video. Thorough yet concise.

@godofplumbing 7 лет назад

I have an E350 cutaway van 12,000 GVW. The leaf spring actually hits the top caliper holding Bolt. On the passenger side. Pain in the ass. By the way, your videos are great. Thank you for your time.

@HowtoAutomotive 7 лет назад

michael chauvette did you take the bracket bolt off and then remove the caliber?

@godofplumbing 7 лет назад

I did. Thanks for the reply

@HowtoAutomotive 7 лет назад

michael chauvette thank you for watching!

@Blinker_Fluid_Supply 5 лет назад

@@HowtoAutomotive for some reason your video does not play

@HowtoAutomotive 5 лет назад

Nelson H. I just checked and it’s playing for me.

@DominicDME 3 года назад

As a commercial truck and heavy equipment tech myself. The advice given in this video is bad and you should know better. For starters the hub seal needs to be replaced every time the hub is removed and you should make that clear. Also putting the hub back on the correct socket must be used and the nut needs to be torqued to spec and backed off accordingly. That’s what sets the bearing preload, when you don’t do that the bearing either will fail prematurely or the wheel end comes off and possibly kills someone.

@user-me4fv3wr9z 2 года назад

I had a customer follow this stupid video so I was going to make a comment, but I'm glad I found someone else that already had, this video is why I make alot if money!

@mrsdargin2006 5 лет назад

all this just to change out some damn rotors and pads? GOT DAMN lol

@MERICANMOTO 2 месяца назад

Because dually that's why lol

@RSDemonof907 2 года назад

One way I've removed the seal inside the wheel. And pull with a seal puller. It keeps the hub from moving and makes a nice sturdy working spot to drive the new seal in. And /or races if you're replacing bearings

@sacongo1624 3 года назад

The engineers at Ford couldn't figure it out how to adopt an emergency brake on disc rotors they had to do a whole second set of drum brakes. Why Ford why.

@DasMoose9001 Месяц назад

Seen it often, not all Ford

@EnriqueGonzalez-zx6vq 11 месяцев назад

Nut to remove axel nut is 2 2/3 Part number w 83008 bought at oreilys

@TheBrokenFarmer 3 месяца назад

Very good video. Is it advisable to replace or at least repack the wheel bearings when you have them out?

@jayfromtexas6718 20 дней назад

Great video. I just got the tires and wheels off. Long way to go before its done.

@atp1962 4 года назад

You have torque specs on all these bolts and I think the axle nut is torqued to 60 lbs and backed off 3 clicks or about 1/4 inch

@kevincheesman 5 лет назад

Do you need to take the seal out to replace the rotor?

@atp1962 4 года назад

Yes because you have to remove the hub to get to the rotor bolts. Make sure you use loctite and torque the rotor bolts as well as the axle nut and the axle bolts.

@nickrhine8127 3 года назад

What is the name of the socket you used to take the special bearing nut off? Also are there multiple sizes what size did you need?

@RiggyRonnie Год назад

Thank you. I always get stuck on that lock ring before the bearing and have to resort to RU-vid videos to figure out what’s next

@colinblankenship2401 5 лет назад

Excellent video. Thank you for sharing

@HowtoAutomotive 5 лет назад

Thank you for watching!

@NJerseyDan Месяц назад

How to, What would be your estimate on labor time for both sides, assuming you dont run into any problems?

@YourSoundStudios Год назад

Thanks for a great video.

@bishopmartinpangburn6341 5 лет назад

Very Helpful video

@SteveRobReviews 8 лет назад

Nice- ok it wouldn't fit on your lift, ha too heavy. Brian the axle you removed does it have the seal built into the inside flange on the axle or is it a replaceable gasket ?

@HowtoAutomotive 8 лет назад

The seal was on the inside of the hub and I has a rubber Pringles at the end of the axle.

@HowtoAutomotive 8 лет назад

Definitely too big for the rack. Lol

@SteveRobReviews 8 лет назад

+How to Automotive Your home page is looking great. Keep at buddy..

@HowtoAutomotive 8 лет назад

+STEVE ROB The goal is to make it better and better. And hopefully help more and more people. Wish I had some of the technical skills you have. Your videos with great!

@SteveRobReviews 8 лет назад

How to Automotive Haha I have by buddy RICKAFIX channel to help me he's the brains of the operation up here. LOL I really like the Sony movie maker platinum 12 , it was a learning curve and still is but now that I have figured out more it makes it so much easier to edit than the windows movie maker. Today's vid would have been a lot easier to film with a tripod. I'll be watching for your two handed vids. LOL

@ronymorales3527 2 года назад

Great video

@knuckleuprambo 6 лет назад

Greatvideo thank you

@master6435 Год назад

It's actually better to open the bleeder screw when compressing the caliper to press out the dirty fluid out instead of pressing the dirty fluid back through the seals and master cylinder

@richarddeichler2172 7 месяцев назад

100%. They way this guy did it is just lazy. That's the dirtiest fluid in the system and you just pushed it back in.

@chrismiller8328 9 месяцев назад

Anyone know a part number or have a link for that seal? Ordered one and it's the wrong one

@jeffrung112 4 года назад

whats the torque specs on the bolts, axlenut, and lugnuts this is the most important thing

@elibrenny4572 3 года назад

just a couple ugga duggas

@oserratos 3 года назад

@@elibrenny4572 never that. Especially when you're doing all this work, would hate to redo it.

@oserratos 3 года назад

Here you go man . . Front Disc Brake- Torque Specifications: caliper bolts (F250, F350) (76Nm) 56 ft lb. caliper flow bolt w/crush washer (48Nm) 35 ft lb. caliper anchor plate bolts (F250, F350) (225Nm) 166 ft lb. Wheel hub extender nuts (176Nm) / 130 ft lb. Brake disc shield screws (11Nm) / 8 ft lb.

@oserratos 3 года назад

Rear Disc Brake Torque Specifications: Brake caliper bolts - F-250, F-350 single rear wheel (35Nm) 26 ft lb. caliper flow bolt (35Nm) 26 ft lb. caliper support bolts (137Nm) 101 ft lb. Disc-to-hub bolts (121Nm) 89 ft lb. caliper anchor plate bolts - F-250, F-350 single rear wheel (275Nm) -203 ft. lbs

@markflynfloat6779 11 месяцев назад

Disc to hub torque specs?

@billymartin1874 3 года назад

Why does the seal have to be removed and replaced?

@HowtoAutomotive 3 года назад

The main reason is it’s added protection since you’re taking it all apart to change out the rotors there’s a good chance the damage could happen. Also the seals get a hard overtime and if they’re not leaking now they will eventually leak.