Тёмный

How to Replace the Rear Brakes on a Volvo C30 S40 V50 C70 

4DIYers
Подписаться 171 тыс.
Просмотров 62 тыс.
50% 1

How to replace the rear brakes on a Volvo C30, this tutorial includes both the replace of the pads and rotors. A similar procedure can also be used on the Volvo S40, V50, and C70 models. In order to produce this video, Bosch has been kind enough to provide me with the parts required for this replacement. #volvo #volvoc30 #brakes
OTC Caliper Kit: www.otctools.com/products/dis...
Website: 4diyers.com
Patreon: / 4diyers
Facebook: / 4diyers
Twitter: / 4diyers
Instagram: / 4diyers
Tumblr: / 4diyers
Pintrest: / 4diyers
Tools/Supplies Needed:
-7mm allen socket
-13mm socket
-3/8" and 1/2" drive ratchet
-thread locker
-wire brush
-new pads and rotors
-standard screwdriver
-brake cleaner
-jack and jack stand
-brake caliper piston tool
-hammer
Procedure:
Being that we are working on the rear brakes, we can’t apply the parking brake. This is a manual, make sure the car is in gear and as an added safety caulk the front wheels.
Start by safely elevating one side of the car.
And then remove the wheel.
Place a jack stand under the subframe as a safety.
Remove the spring clip on the caliper. Use a standard screwdriver to pry it from its location, pliers may also help too.
Using the standard screwdriver again, remove the caps for the caliper pins.
Using a 7mm allen socket with a 1/2” drive ratchet, remove the caliper pins, there are two in total.
Ensure those pins aren’t catching on the carrier and then remove the caliper. Tie the caliper up using a bungee cord so there’s no excessive strain on the rubber flex line.
Remove the brake pads from the carrier. They simply just sit in place.
To remove the carrier, it’s held on with two 13mm bolts. Here you’ll need a 3/8” ratchet instead to clear the hub carrier.
Using brake cleaner, wash away brake dust on the dust shield. Inspect the condition of the dust shield and replace it if needed. This is also a great time to inspect the condition of the rear wheel bearings too.
Wash the caliper using a brake cleaner.
Crack the cap on the master cylinder help relieve pressure from compressing the pistons.
These cars have the parking brake mechanism built into the caliper, therefore you’ll need a special tool to push back the pistons instead of just compressing the piston. Bosch has supplied me with their OTC disc brake caliper tool to do this. The piston has two holes, this kit has adapters which lock into those holes, the piston is rotated and you’ll need to compress the piston at the same time.
Using a wire brush, clean up the carrier. The brake pads should sit freely on this, no binding whatsoever. Compared the old and new rotors to ensure they are the same.
A wire brush may be needed to clean the hub to reduce the chance of runout when the rotor is installed, this one is in good condition so there’s no need for that. A lug nut can be used to help hold the rotor into place.
If you leave any oil residue on the rotors, clean them off using brake cleaner. Clean the carrier bolts using a wire brush. Apply a medium grade thread locker. Install the carrier with bolts. The torque specifications for the 13mm are 52 ft-lbs or 70 nm.
Install the out pad, these pads should fit freely into place. For the inner pad, a new spring clip is supplied and will need to be installed on the new pad. It wedges over a thin portion on the pad backer. Then install it into place.
Install the caliper into place, I have also removed the pins as they will be cleaned and have new lubricant applied. Clean the pins using brake cleaner and even a wire brush.
Apply medium grade thread locker to the threads. Apply a light layer of the supplied brake grease to the pins. Install the pins and tighten. The torque specifications for the caliper pins are 26 ft-lbs or 35nm. Install the plastic caps.
Install the new supplied spring retaining clip on the caliper. I found it’s easiest to install it partially into the one hole first, partially into the other and then pull it under the carrier before it’s fully seated. Light taps with a small hammer can help it to place. Reinstall the wheel. The torque specifications for the lug nuts is 80 ft-lbs or 108nm.Now moving onto the opposite side.
Thank you to all those who watch my videos and support my content. Don't forget to subscribe to my channel for future tutorial videos and like my video if you found it helpful. New videos are always being uploaded every week!
© 4DIYers 2013
All Rights Reserved
No part of this video or any of its contents may be reproduced, copied, modified or adapted, without the prior written consent of the author.

Опубликовано:

 

13 окт 2019

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 67   
@4DIYers
Amazon Tool Recommendations:
@steveforbes756
@steveforbes756 4 года назад
Well done. I wish all how-to videos were like this
@vinhchau6561
Clear video, instructions and easy to follow. Thank you !!!
@bigtd7399
@bigtd7399 2 года назад
I have a volvo and so far its been a better car than any American car.
@erlandskoglund7491
Now i feel very confident i can do this my self, thanks!
@williammitchell1804
@williammitchell1804 2 года назад
The tool kit I used was "Maddox Disc Brake Pad and Caliper Service Tool Kit MF11-1". The attachment labeled 3 fit the back brake caliper for my 2005 S40, manual transmission. If your brake piston is stuck, try a little WD40 just below the rubber then twist the piston clock-wise with channel locks to get it started. Be patient, because the tool looks simple but requires practice and so does installing the new retainer.
@averageautomotiveenthusias9555
@averageautomotiveenthusias9555 3 года назад
Thank you sir, excellent video 👍
@yessirskiii2615
@yessirskiii2615 2 года назад
Sooo I have a piston kit and I decided not to mess with it and used a c clamp for my front calipers. Got to the back and thought they were seized up so I gave up. Glad to know I’m a moron and I even have the correct tools for the job!
@marklemay3907
You can also put some brake grease on the caliper bracket where the pad lobes sit
@nanoceramics2747
@nanoceramics2747 Год назад
excellent . well done clear and concise
@pazy5000
Best description
@alexresendiz5101
@alexresendiz5101 2 года назад
Excellent video with great instructions. So is there enough room (clearance) to install extended studs without removing the hub or making a dent on the dust shield?
@orfeous
@orfeous 4 года назад
My rear ATE brake discs came with two screws and an extra hole. Whats are these for? My Volvo OEM doesnt have that.
@charliediver1560
@charliediver1560 3 года назад
Geat video . Wish all videos were as well explained .
@jh1544
@jh1544 Год назад
Great video, my 13mm bolts are seized on - and ideas?
@rickh8093
5 star, A+, 10 out of 10
@lincolnhawk4671
@lincolnhawk4671 4 года назад
Tool at
@bryanmiller5074
If only it was that easy
@arthurwhitelam6591
What's the tool called for winding back the callipers please
@eric_b_
@eric_b_ 3 года назад
Hey, great vid.. I appreciate it. I did everything as instructed. My only question is, when depressing the piston - i had a tool, and was able to make it turn and compress until it became pretty easy to turn and seemed to be down. but it never stopped turning.. did i give up too soon? I'm hearing the same rubbing i was hearing before i replaced the rotor that i had attributed to a warped rotor (which i still believe it was). Is it possible that the backing plate is bent and rubbing? I appreciate your help in advance..
Далее
Я КУПИЛ САМЫЙ МОЩНЫЙ МОТОЦИКЛ!
59:15
ТРОЛЛИНГ СКАМЕРА СТАНДОФФ 2
00:59
Kettim gul opkegani😋
00:37
Просмотров 1,6 млн
ВОТ ЧТО МЫ КУПИЛИ НА ALIEXPRESS
09:35
How to: Volvo C30 S40 V50 C70 Right Axle Replacement
8:14
The Only Brake Pad You Should Buy
10:07
Просмотров 814 тыс.
Most Common Brake Installation Mistakes!
13:29
Просмотров 4,4 млн
Replacing the Rear Brake Pads on a Volvo S40
4:28
Просмотров 119 тыс.
How to Replace Rear Brakes 01-07 Volvo V70
14:55
Просмотров 38 тыс.
Я КУПИЛ САМЫЙ МОЩНЫЙ МОТОЦИКЛ!
59:15