How to Replace the Thermostat Housing on a 2005 Land Rover LR3

Подписаться 218 тыс.

Просмотров 57 тыс.

50% 1

Brian Eslick from How to Automotive www.howtoautomo... takes you step-by-step through the process of replacing the thermostat housing on a 2005 Land Rover LR3.
Affiliate link mentioned in the video for Thermostat Housing amzn.to/2gzXWwF
Affiliate link mentioned in the video for Prestone AF2100 Extended Life 50/50 Antifreeze - 1 Gallon amzn.to/2qrpdpe
Website
For more videos, tips, and to purchase recommended tools and products visit my website at: www.howtoautomo...
Stay connected at:
Email: howtoautomotive@gmail.com
Facebook: www.facebook.c...
Google+: plus.google.co...
LinkedIn: / brian-eslick-819839118
Disclaimer
Owing to factors beyond the control of How to Automotive/Brian Eslick, it cannot guarantee against unauthorized modification of this information, or improper use of this information. How to Automotive/Brian Eslick assumes no liability for property damage or injury incurred as a result of any information contained in this video. How to Automotive/Brian Eslick recommends safe practice when working with power tools, automotive lifts, lifting tools, jacks and jack stands, electrical equipment, blunt instruments, chemical lubricants, or any other tools or equipment seen or implied in this video. Because of factors beyond the control of How to Automotive/Brian Eslick, no information contained in this video shall express or imply warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or information contained in this video is the sole responsibility of the user and not How to Automotive/Brain Eslick. #howtoautomotive #AutoRepair

Опубликовано:

6 окт 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 51

@MisadventuresInAuto 2 года назад

Thanks for posting this. I did a few things differently, but a flex head with a wobble extension was absolutely key to getting the bottom bolts out of the heads. Very glad I got it done instead of just leaving it with a new expansion tank and level sensor since there was major corrosion around the temp sensor, some of the bolts, and a visible crack down the top sitting below the intake. Pro tip for anyone watching - ANY time you see black plastic housing or other parts of the cooling system start to turn brown, time to replace it ASAP!

@ChristofBove Год назад

Thanks for posting this video! If you remove the fan cover, fan, and front coolant hoses, you can easily access throttle body bolts. Doing this made fitting new housing roomy, assuring that all bolts are seated properly. Great opportunity here to clean throttle body as well!

@Threeuselesscars 2 года назад

Thanks for this video. The other video I saw said "pull the intake manifold" and the idea of that made me question every life choice that got me here. Appreciate that saner eyes looked at this problem before mine.

@traildave1 7 лет назад

What a Godsend you and this video are! Thank you! Just finished this afternoon and all appears to be working. Thanks for giving me the confidence to tackle this fix.

@HowtoAutomotive 7 лет назад

traildave1 glad to help. Thank you for watching!

@rlarajr2001 2 года назад

Getting ready to do the job on my car. Your video was very helpful.

@kriswalker1898 5 месяцев назад

Getting ready to tackle this job today, thanks for the video and tips.

@rafaelciura9545 5 лет назад

Thanks for uploading this video. I just finished this job in 3 hours and your video was key to making it happen. I took my time removing the bolts. Some of them were really tight and had to be extra cautious removing them. Thanks again!

@JonniArmani 7 лет назад

Brian you rock! just finished this today! Thank you.) that left bottom 28-30 Torx is a bugger! have a great summer! J.

@HowtoAutomotive 7 лет назад

Jonni Armani glad the video helped. Thank you for watching!!

@svenrichter8231 7 лет назад

Another great video. Just finished this 10 mins ago. Lower control arms as well per the other video. THANK YOU!!!

@HowtoAutomotive 7 лет назад

sven richter glad to help. Thank you for watching!

@taemian Год назад

Great video!! Saved me time and hassle. Only thing I would add is to loosen the black steel coolant line a bit. Helps you get more wiggle room, and yes a magnet is a must have

@bjohnsonsv 6 лет назад

Exactly what I needed to do this job! Noted that you'll need to buy new throttle body gaskets and EGR gasket for best results. Note that if you buy only the thermostat housing at most places, it includes the o'rings for the openings, but not the TB and EGR gaskets.

@reyguerra6305 6 месяцев назад

Thankyou so much this made the project way easier

@sheltonboatwright6023 7 лет назад

Great video i did mine today what a big help did it about hour and half without this video probably would have taken 3 hours a magnet is a must

@HowtoAutomotive 7 лет назад

Shelton Boatwright glad to help. Thank you for watching!

@westbarba529 3 года назад

Really appreciate your help with this video. Great job Sir.

@joecool509 7 лет назад

i removed the yellow the yellow clips and installed the two parts separately. made it easier to access the intake bolts and was able to pull everything together, the original didn't even have the clips.

@sarahdell4042 Год назад

Do you go for a test drive with the expansion tank cap off to allow air to escape?

@itsmisale Год назад

thanks for the vid bro, this housing such a headache

@ryanragsdale8915 Год назад

Great video, thank you

@jessesward9429 4 года назад

Broke the pcv vent hose he mentioned, it’s $70 and nobody makes an after marker one, gotta love these rovers

@HowtoAutomotive 4 года назад

Jesse Sward sucks that happen.

@a.mccomb3296 5 лет назад

Big help! Thank you.

@HowtoAutomotive 5 лет назад

Andrew R. McComb thank you for watching!

@blakeleeper9836 6 лет назад

Thank you for the Perfect video! Nice job! I have one question? I heard you are supposed to remove the yellow clamp on the housing after you install it. I heard that the yellow clamp restricts the expansion from the heat so there is even wear on the o-ring

@blakeleeper9836 6 лет назад

. Thank you B

@christianhurston 4 года назад

Great video! I changed the thermostat housing with a genuine assembly...changed coolant housing and coolant. Engine is still overheating though. Any ideas? Wonder if water pump isn’t moving the coolant? Wasn’t able to get all 3 gallons of coolant in when I changed it out. Any suggestions would be appreciated.

@hardatbarran5553 2 года назад

You need to bleed the system more so that trapped air in the heater matrix is expelled. When you set the cabin heat on max and blower on max you should be getting full heat in the cabin; if not then bleed some more.

@edsim6021 3 месяца назад

Did you use any gasket maker or silicone gasket or RTV or anything like that.

@HowtoAutomotive 3 месяца назад

Nope, just a gasket O-ring that it came with

@efrainavena2672 4 года назад

very helpfull

@HowtoAutomotive 4 года назад

efrain avena glad the video is helpful. Thank you for watching!

@haroldskow8443 7 месяцев назад

I see you did not use any sealant. Is that correct?

@jahsidmatias3625 Год назад

Currently doing this job, can’t sneak anywhere on this engine…..I took off all the hoses first, then wanted to remove the 4 bolts holding the throttle body to the plenum thinking that would release everything together…nope, you have to separately remove the air tube from the throttle body then you can remove the throttle base……if you try to take off the throttle body hoping the air tube will come with it, Land Rover/BMW/Jaguar made sure the bolts jam against the air boot so you have no clearance and just remove everything piece by piece 🤦🏻‍♂️

@jeremycaraway18 7 лет назад

I didn't really understand what you used to get the hardest bolt for the throttle body off. I heard 8mm wobbly socket? I couldn't find one at O'reilly's so if you could let me know where to find one, it'd be a huge help

@HowtoAutomotive 7 лет назад

Jeremy Caraway I used a 8mm quarter-inch wobbly socket with a long extension.

@Denkha94 7 лет назад

hi there great video. can that bleeder hose be removed the one that's underneath the thermostat housing and under the intake manifold. can that clamp be undone and hose removed without removing the intake manifold. land rover part# is LR006158 thanks

@paulwaterlander6182 3 года назад

The only way to replace that hose is to remove the intake manifold. Only Land Rover would place the end of a coolant hose under the intake manifold. Also, you will find this information NOWHERE on the Internet....it is all trial and error. Caution: you more than likely will need to replace the intake manifold gaskets after you replace the hose, as it may set off a vacuum code error once you put it all together again! Super frustrating.