How To Replace Wheel Hub & Bearing 2004-08 Nissan Maxima

Подписаться 517 тыс.

Просмотров 40 тыс.

50% 1

Buy Now!
New Wheel Bearing & Hub Kit from 1AAuto.com 1aau.to/ia/1ASH...
New Wheel Bearing & Hub Kit from 1AAuto.com 1aau.to/ia/1ASH...
Not only can a worn wheel bearing or hub be annoying if it is noisy or vibrating, but it can also lead to accelerated wear in other parts, or unsafe driving conditions. Replacing your worn bearing or hub with a quality TRQ part is a safe, smart, decision. This video shows you how to install a new wheel hub and bearing on your 2004-08 Nissan Maxima.
• Check here for more videos on the 2004-08 Nissan Maxima: • Nissan Maxima 6th Gene...
This repair was done on a 2008 Nissan Maxima SE 3.5L and the process should be similar on the following vehicles:
2004 Nissan Maxima
2005 Nissan Maxima
2006 Nissan Maxima
2007 Nissan Maxima
2008 Nissan Maxima
Tools you will need:
• Pry Bar 1aau.to/oeI/1AX...
• 22mm Wrench
• 12mm Socket 1aau.to/oqG/1AX...
• 18mm Socket
• 19mm Socket
• 21mm Socket
• 32mm Socket 1aau.to/oy/1AAS...
• Brake Caliper Hanger 1aau.to/oav/1AX...
• Side Cutters
• Snap Ring Pliers
• Torque Wrench 1aau.to/oj7/1AX...
• Brass Punch
• Large Hammer
• Pick 1aau.to/ode/1AX...
Subscribe: / @trq
Check out our playlist:
Nissan Maxima 6th Generation 2004-2008: • Nissan Maxima 6th Gene...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.

Опубликовано:

15 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 28

@TRQ 3 года назад

√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts √ *Do it Yourself* √ *Save Money*

@TheChuyDewy Год назад

yeaaa this is one im gonna have to take to the shop dont have a press

@dangolfishin Год назад

I have an 05' Sentra but will use this as a reference since all the Sentra bearing vids are garbage. Well done bro!

@PC-ni3zj 4 месяца назад

Thanks

@mikedoso9760 Год назад

How do you know which side of the bearing faces the abs if neither side is magnetic?

@Cedd2times Месяц назад

Heads up buy bearings already pressed in.

@TRQ Месяц назад

+@Cedd2times Thanks for the feedback! 1aau.to/m/Shop-TRQ

@IIsWolfee 6 месяцев назад

Could you put the hub in the Bering first and then press the bearing and hub into the knuckle together?

@mathewmedina2233 Год назад

I hammered the axle bolt and mushroom the end before watching this what would be a good fix to get axle nut back on

@ShOtTaLk2AZ Год назад

Idk why nobody else spotted this but the rotors aren't facing the right way. If it cross slotted/drilled.. the holes face the direction of the rotation.

@Mickey_Bauer 3 года назад

No grease needed between the bearing and knuckle or hub and bearing when installing? Thanks!

@michellelysien5739 11 месяцев назад

An auto repair shop is telling me the entire CONTROL ARM , not just the wheel bearing, needs to be replaced. A friend is telling me it just needs what is being done in this video. ANY ADVICE ???

@kitchenup8747 2 года назад

thank you

@jjfernandez5044 2 года назад

does it matter if the car gets replaced with non abs bearings ??

@97336cf 2 года назад

You will have an abs light on and no traction/stability control or ABS

@kainhall Год назад

10:26 also... NEVER loosen it to line up the holes . If you arnt strong enough to turn it anymore..... take off the nut, hammer the taper to pop it out.... and start COMPLETELY over . You CAN NOT loosen it off, then tighten it again (with out hammering the joint to pop the taper free) . . . You can get them too tight and Crack the taper.... but with this cast iron steering knuckle, that's hard to do (aluminum is easy to Crack if you go to like 250 when spec is 25 lol) . . . Tldr... NEVER loosen Always tighten . And if you can't tighten anymore....start COMPLETELY over

@Kohplay88 3 года назад

Like a pro👍 Very nice presentation!! Thank you

@michellelysien5739 11 месяцев назад

Last comment ... my car is a 2006 Nissan Maxima SL ...

@googlemall3323 2 года назад

Good money

@mistacdawg6882 2 года назад

I been trying to get my snap ring off for 3 days and spent over $300 on tools just to get it off.. any other tips please. My snap ring made just like in the video with no holes. The pointy tool just slips off. I used torches and all

@Kevin-bl6hx 2 года назад

Once you have the hub removed from the knuckle use your favorite rust penetrator/ dissolver and use liberally all around the snap ring, the entire key to the removal of the snap ring is you need to get the end of the ring (either side) away from its channel so you can slide something/anything behind the ring but in front of the channel it slips in , then you work a screwdriver around as he demonstrated at (5:40) of this video. A good quality set of picks is a must . To gain leverage with the pick once you get the tip behind the ring you can use a screwdriver behind the pick to press raise the ring out of the channel . A second set of hands to place the screw driver behind the exposed ring helps while you are getting the clearance to do so with the pick . Watch and cover your ring when it is close to coming out & as I have seen the ring fly with some real velocity.

@jerrydeguzman 2 года назад

Takes a LOT of perserverence. For the first bearing, I spent over eight total hours trying to shimmy and hammer and force screwdrivers and picks under the ring, before finally getting it off. For the second bearing, I ended up grinding away a portion of the "lip" that holds the snap ring in, near one of the ends of the snap ring. That made it a little easier to get a small screwdriver under the ring in order to pry it out the rest of the way. It's not an elegant solution, but it worked and saved me HOURS of frustration. But I did see a homemade tool on RU-vid (looks like a large, angled pick) that made the work look incredibly easy.