HOW TO SET YOUR WAHL CLIPPER BLADES 

I wish I would have seen this before running to the pet store to get new replacement blades which didn’t fit. After I saw this video I realized that the old blades were installed wrong and they worked like a charm. This was the best tutorial and I appreciate you taking time to share your knowledge.

Great, clear instructions. They were not alligned and now they trim hair, not rip it out like before. The voltage tension section was really helpful. Thank you

BEST VIDEO!!! I've watched plenty of these tutorials just to compare, and your video is the BEST in close up photography and clearly explaining the correct WAHL recommended alignment procedure. Well done brother.

This was the clearest explanation and visual for blade alignment video I have found. Thank you. It helped a great deal……

Had my clippers for years then they stopped working, took them apart and cleaned them, put them back together now working and cutting smoother than brand new, nice one 👊

Best video I've seen yet, and it's all close up to see how the teeth, should line up awesome job Thank You sooooo much!!! ✌️

By far, BEST WAHL tune-up video I've seen. Thanks.

Just what I was looking for, clear instructions. Thanks 👋👍👍👍👍

Thank you! First, you helped me to become familiar with my new Wahl (battery type, made in Vietnam, no adjustments here, but mechanics similar), then I decided to check my ages-old SF-938 haircut machine, too, which has the same parts but much bigger (45mm, to be plugged into the mains only), get out approx. a pound of hair stubbles from the inside and do maintenance and adjustment after reassembly according to your instructions, too. It is amazing how silent that one has become now 😅.

Soo helpful, thank you so much, and even with the bonus info at the end about tuning! I've thrown away clippers for making that grinding noise before... now I know why that was happening! Thanks!

Very well explained - measured and clear 👏👏👏

God bless you bro. Just got it. Shaved, bathed and now in Church. This is my 1st time resetting the blades of my clipper myself. And the problem was that the lever didn’t lap well with the new blades grove. So I trimed the lever a bit. Made it ever all the way, then when i screwd it tight it didn't lap. Then i loosed it and made it sit on the lever and carefully placed the blades and screwed gently to hold and reposition the little blades untill they lapped as you showed us the teeths should lapped then tightened and started it and the blades didn't fall off this time as did after the vendors set it themselves. But then it made a loud noise then i screwed the voltage screw up n down till the sound was gentle n smooth. Then shaved the hair on my hand to make sure its working ir did. Then shaved myself neat and jumped in n out the bathroom n out to Church. Just singing the Entrance him now b4 the Priest comes in. Took me about 45mins to sort it. Got it on the 3rd time. Almost gave up cos was running late to Church. Thanks to you i look good on my bday.

You are fabulous!! Love the instructions ... and your voice tone... fantastic....! Thank you for the help....

Thanks, I've always thought I'd kept my clipper in tiptop condition, but I never aligned the blade's right way! Now i knows, thank u very much indeed!!! 🤟👍❤️🤟

Thanks a lot brother for this well explainatory clear visual tutorial. So so helpful. Will go practice it now. They fixed it for me where I bought the blades but coming back home to use it turning it on the inner blades kept shifting. So watching this video whilst eating, now i have courage to DIM. Thanks again bro. It's my bday today "Sunday". Not had time all week to go to the barbers n still don’t even have time today "my bday" as it is the deadline for some assignments i have to submit" but i still want to look good on my day. Thanks again. Will let you know when it works. Cheers. Just about to take a shower n head to Church.

Tooth alignment is what I came to RU-vid for. Thanks man.

Thanks for showing this 👌

Oh that's a good tip with slightly tightening each screw in an alternating fashion. I kept moving the damn blade when trying to tighten it down. Very nice video.

Thanks a lot. After doing mine, i was having doubts (never been taught or seen someone do it before). Glad I'm on track

Thank you. I found Lanoline spray lube completely changed the way mine work. Just brilliant.

Very straight forward and an outstanding tutoring. Keep it up...

Thank bro. Very educational and clear instructions.

I have a special needs son and hair cuts are a chore, my clippers got loud and were scaring my son. The tip on changing the voltage is a life saver, I was about to replace my clippers. Thank you.

Had to come back to the video , got to remember the basics sometimes!!

Thank you for your help today

Wow that was a useful video , thanks for posting it .

I had all the information except the side screw voltage adjustment. I was trying to find the sweet spot for the stationary blade screw tightness since when I tightened it completely the cutting blade would not move. I could cut a bit then the screws would loosen to much and cause issues. This was perfect now I can keep a nicely manicured beard and mustache. Thank You!

Thanks man. This has been useful

AWESOME instructions. Thanks for sharing. Subscribed

Great video, I finally understand what to do with my clippers!

Great job. Really helped.

This was perfect!

This is the best tutorial 10/10

Spot on great vid thanks👍🏼

Right on. Thanks for the info. Easy.

Excellent video!!

Ty You helped me soo much

My little son threw my on the floor and cutting blade shifted off it position and when I try looking into it, it fell off. Loosing the blades I noticed the foamy is torn and the white rubber/plastic have receded inside that the cutting blade can't latch on it. What do I do to fix it and align the blades again?

I am so frustrated!!!! After taking the clippers apart now i can’t line them up again and they won’t cut. Thanks for the instructions I will search for a better pair that i won’t have this kind of trouble tuning them!!!

I bought new wahl clippers and they were pulling my hair and not cutting even after I oiled them and I watched your video and turned up the voltage.I'm good now.thanks

How often do you do this maintenance?

Thanks bro, for years I've been wanting to know how to tune my machines.

Thank you for the cleaning and alignment advice. Does anyone know how to get a replacement for a damaged foam hair filter? Is that really necessary or is it OK to operate the device without one?

My question is about the left/right alignment of the bottom blade. The top blade moves left and right, and each time you switch on the clippers then switch it off, the top blade doesn't stop in the same position every time. So when aligning the bottom blade, how do you account for this? What position of the top blade do you go off to set the bottom blade? Thanks

i just bought a blade replacement and 1 tooth is half the length of the others. Will that cause me a problem?

Nice video man thanks take care

Great. Thank you.

Thanks for this tutorial, it’s a truely really informative. (The positioning between the 1st and last tooth) just one question, how do you measure the 0.8mm? The reason I ask is that I have a wahl magic and I recently adjusted/zero gapped it, and I’m not sure if it’s made things better for me, I feel that it may have made things abit harder to see (too close) on a fade (when setting a no guard open guideline & #1 guard open guideline) I’m thinking of changing it back to the factory setting, hence watching this video.

Great video! But I have a problem. My clippers made a loud sound before. I re adjusted the blades and it stopped without adjusting the power screw. It started again and I tried readjusting the blades and power screw again. Blades are aligned. But the sound is very loud and even after power screw adjustment. What do I do now?

Thanks ☺️

Tha man! well explained shot bro now when i get back home from my holiday gonna try this thought my clippers were broken lolz..👍

What do you do if you lose or misplace your filter for your Wahl ? Can you get a replacement ? Where at ?

thank you so much. I should have watched this video long ago.

Cheers!

EXCELENTE VÍDEO Y EXPLICACION

Whats the model

Nice work ❤

Top notch video.

thanks so much!

Thank you!

Best vidio

First tooth of stationary blade doesnt lie on second of moving one yet it cuts alright. But how to trim without scratching on beards skin?

thanks mate!

Thank you buddy one year problems👍👍❤

Tnx bro your cool👍

Yo mate, I was having an issue with my clippers. I watched your video and followed what you said to do. It's late now to be making clipper noises, so I will update you in 2 days.

Good settings

Excellent.

I have a question about this product has a big noisy?

Y is the two blade not equal?? Cus in my place we use the clipper for lineup too

Could you able to tell me the size of the screws please. Thanks

Good video

Wahl done my friend.

Thanks 💐💐💐🙏🙏🙏🙏

Damn i did it n now it cuts smooth doesn't cut my skin 👏

What was that soft felt hairy piece you removed from between the blades (0:30)? I do not have that on my unit.

I was on 1 blade short from going bald and going to the shop looking like the 3 stooges I was determined and fixed and oiled it up like new thanks

Thanks, you saved me money that I didn't have to spend. #lifesaver

If the cutting blade can’t sit straight but sits crooked because of the plastic piece that goes in the center of it, then it’s a manufacturing defect right? The top blade on mine can’t be angled enough to compensate for the crooked sitting bottom blade. It stays crooked since the cutting blade is held in place crooked to begin with

Everytime I screw down, and I use so much attention, the teeth move. I hate the Wahl system it's like they want us to fuck up the clipper

nice video

Sigh - "..With the lever fully closed.." so is that move it to the closest or longest cut? You move it to both extreme so its not clear which one its supposed to be

Bende aprilla marka traş makinesi var başlıkları 2 si hiç kesmiyor körelmiş nasıl bilenir

Why does another video say set the left last tooth between the the left last gap on the moving blade?

Prices of cliffers

What oil should I use? So don't need to soak or scrub in a solution or anything?

Tysm man😭🙏 I went to clean my clippers and uninstalled the blades and went to put it together… turns out I installed it inverted so the blades kept rubbing against each other making a loud noise😂 again thank you I realized mid way my mistake

I have one clipper that’s zero gapped all the way to the end of the stationary blade to erase trimmer line and the rest of my clippers are like yours

Is it normal for the small blade to move side to side with my finger even when tightened?

Boss mgkano b reasor na gaya sau boss

Sweet as, Bruv.

What type of oil did you use pls? ❤

Can I use it for dog?

Walh clippers seem a little temperamental, imho. I think i am going to shop for ky next set, that does not have that adjuster arm. Im more than happy with guard attachments to give my desired hair length

Excellent clip, except that you are not adjusting the "voltage" with the side cross-headed screw, just the tesion in a spring, which changes the off position of the moving blade and how far it moves. I hope it helps

Thanks for this information. Hopefully my trimmer won't rip my hair out like last time! 😂

💎💎💎

👍👍👍

The white plastic in the middle has shifted to the corner 😥 I don't know what to do. I thought the first clipper was supposed to go over the plastic , but you didn't put it on. Been wasting my time trying to put it over it😅

UP THE WAHS!