Тёмный
No video :(

How to setup WLED for your NeoPixels led Matrix with an ESP32 | WS2812B 

Bloxy Labs
Подписаться 1,1 тыс.
Просмотров 7 тыс.
50% 1

Опубликовано:

 

27 авг 2024

Поделиться:

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист
Посмотреть позже
Комментарии : 10   
@mybritishcomputerguy
@mybritishcomputerguy 6 месяцев назад
Nice little video, however you are missing several steps. You didn't talk about powering your Matrix, USB is not a good solution AT ALL for this many Pixels. flashing your ESP32 I doubt was that simple, you didn't mention holding the boot button down for your computer to connect to it properly. Also the version of WLED 14.1 "Hoshi" uses GPIO 16 by default, not 2, you could have just left this alone in the settings and told your viewers to attach DIN wire to D16 in the first place. Also, just a tip about your subtitles... the pop out type of subtitle is difficult to read, may I suggest a fade in static text or something less wobbly. Overall it was a pretty pretty little video. I'm guessing you don't have too much experience with WLED and ESP32 though? One last thing, I saw your comment to another user about powering via the onboard USB port. Not a great comment, the onboard USB can only handle about 1 Amp (1000 mA) any more than that can potentially fry the ESP32 and render it useless, thankfully WLED turns on power limiter by default. With 256 Pixels each requiring 0.06mA to achieve a full White color, with a 1Amp USB power supply you are only powering your matrix to about 6.6% of its potential. You would be much better off powering your ESP32 with a more powerful power supply via the VIN and GND pins and then running the same leads to your matrix to power that too. I cover all this on my channel. I've been working with WLED and LEDs for a while now. I still have a lot left to learn though. Good luck with your channel. I'm going to subscribe and will be sure to check out some of your stuff. (Sorry to sound so critical, hopefully it was helpful in someway)
@HelicopterHatHacker
@HelicopterHatHacker 2 месяца назад
This video helped me. I've seen your videos before. They've helped me as well.
@daisym6503
@daisym6503 6 месяцев назад
This is an amazing tutorial. Thank you.
@kevinkearns6779
@kevinkearns6779 6 месяцев назад
Good job😊
@philmcandrews
@philmcandrews 6 месяцев назад
Great tutorial. Is it ok to power this through the board without external power to the LEDs?
@BloxyLabs
@BloxyLabs 6 месяцев назад
Thanks😊. With the WS2812B which I used it was no problem.
@mybritishcomputerguy
@mybritishcomputerguy 6 месяцев назад
I wouldn't, as each Pixel requires 0.06mA to achieve a full bright white, it means you would need to push about 15 Amps through the USB port. The onboard usb connector can only handle a draw of about 1Amp or 1000mA any more than that and the ESP32 will fry! Also, at 1Amp the LEDs will be pretty dim. I cover this quite a bit on my channel.
@HelicopterHatHacker
@HelicopterHatHacker 20 дней назад
I’m powering 2 8x32 and 1 8x8 through my ESP32 which is powered by the USB-C power from my desktop computer (usb-c to usb-c). It runs non stop no problem. I had the same setup (minus the 8x8) powered through a usb wall adapter and it fried my ESP32. I saw the smoke.💨
@sysadmin-info
@sysadmin-info 10 дней назад
Thanks. It works. I tested it with ESP32 38-pin WROOM. See my channel to see what I am talking about.
Далее
Smoke 😱
00:26
Просмотров 1,5 млн
Only I get to bully my sister 😤
00:27
Просмотров 30 млн
Setting up an LED MATRIX in WLED!!
13:47
Просмотров 65 тыс.
16 x 16 Matrix Display with WLED
4:05
Просмотров 7 тыс.
Forget WiFi! This Wireless Method is WAY Better?
12:14
Просмотров 561 тыс.
English by 3ATIVE
18:49
Просмотров 47 тыс.
RGB LED Matrix with an ESP32 - How to get started
8:11
Smoke 😱
00:26
Просмотров 1,5 млн