How to Slide your Ferguson TE20 Together After a Clutch Repair in Real Time.

Подписаться 50 тыс.

Просмотров 20 тыс.

50% 1

Hello Im Lance (aka Bundy Bear) and doing these videos is my hobby. I do own Queensland Tractor Spares in Australia where I sell parts and offer technical advise to customers.
Parts seen in our videos can be purchased from www.queenslandtractorspares.co...
We have a lot more than we can offer on our web site available to us and in our store. If you dont see what you would like please email info@queenslandtractorspares.com.au and we will help where we can.
I do try and help with technical advise at bundybearsshed@gmail.com if you have a question or are having trouble with your project.

Авто/Мото

Опубликовано:

30 июл 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 67

@jvin248 2 года назад

I split and reassembled my TO35 this last spring and it was such a good feeling when those splines finally aligned and the sections slid together. Turning the PTO shaft proved important.

@BundyBearsShed 2 года назад

Yes turning the pto helps a lot.

@johncopse9663 2 года назад

Very informative video Lance hope you and your family are all keeping safe and well

@BundyBearsShed 2 года назад

Thanks, you too!

@TheComander1234 2 года назад

That clutch tip was nice! I would not have thought about that myself :P

@BundyBearsShed 2 года назад

Glad you liked it!

@orion-se6bv 2 года назад

greeting Lance from the middle U.S. thanks so much for the clutch check tip I am about to split my MF 65 tractor and this has given me the confidence to tackle the job I also took notice of your track set up and will build something similar I'm grateful you have taken the time to share your vast knowledge

@BundyBearsShed 2 года назад

Glad to help

@darrenblattner2508 2 года назад

Neat test for the clutch lance, never saw that before either. Your right full of surprises. Keep smilin

@BundyBearsShed 2 года назад

Thanks 👍

@basilbrush3836 2 года назад

Thank you for shearing your knowledge,I have all this to go through in the next couple of weeks.(Auckland lockdown project)

@BundyBearsShed 2 года назад

Good luck! Its not too bad of a job.

@hondaman8875 2 года назад

Great bit on the clutch test

@BundyBearsShed 2 года назад

Glad you liked it!

@davidthomas1732 2 года назад

Good job Lance.. Made me think it would be a hard job outside .

@BundyBearsShed 2 года назад

Its ot too bad, the rails help a lot.

@irishmanshamrock8563 2 года назад

Great video Lance and a very useful tip about the clutch. Thanks for sharing.

@BundyBearsShed 2 года назад

Glad it was helpful!

@billweir6770 2 года назад

A great short series of videos...enjoyed them all, and a great way to spend another period in isolation. Great tips that I'll remember next time and I especially enjoyed watching you fit the ring gear, and the clutch pedal setup and checks...all good stuff. I'd love to see a video on you do one on a double clutch and how you push it back together.....

@BundyBearsShed 2 года назад

Shouldnt be too far away if things go to plan

@billweir6770 2 года назад

@@BundyBearsShed Brilliant...we may even have a splitting track built with a bit of luck 😀

@bearwill4737 2 года назад

Outstanding picture quality Lance & as usual top notch mechanic's from a Master !

@BundyBearsShed 2 года назад

Many thanks!

@CharlieSmith-yh6tw 2 года назад

Thanks for sharing this excellent demo.

@BundyBearsShed 2 года назад

My pleasure!

@vincentburrowes9243 2 года назад

Lance - the clutch test prior to fully assembling the tractor - excellent idea. This is the first time I have seen this test. Loctite 515 removal - have you tried Loctite SF 790 Chisel Paint Stripper (Gasket Remover) 510g to remove the gasket?

@BundyBearsShed 2 года назад

No I have not seen the SF790. I will ask my supplier about it.

@vernonjones3613 2 года назад

That was brilliant lance really good tips cheers mate

@BundyBearsShed 2 года назад

Glad you enjoyed it

@dianegriffiths2460 2 года назад

Great tip on the clutch Lance thanks tractor Ray England.

@BundyBearsShed 2 года назад

Glad to help

@ianahmet9286 2 года назад

Another good video Lance

@BundyBearsShed 2 года назад

Thanks Ian.

@charlesvanderwolf5751 2 года назад

Thanks Lance ---You have showed me a few things that I would not have done, and how necessary they can be. Regards Charles.

@BundyBearsShed 2 года назад

Thanks Charles ,Glad to help.

@tridbant 2 года назад

When I did my TEA20 I had to do it outside. Due to the uneven surface I found the rear end twisted at an angle as it was going together. That took quite a bit of time to realign otherwise it would have been rather easy. Good ole Fregie.

@BundyBearsShed 2 года назад

yeah they can be a bit difficult now and then.

@jeskasper 2 года назад

I have to do mine outside as well. Any tips as how you did it, and what I should look out for? I don't have the fancy trolley jacks that Lance does.

@tridbant 2 года назад

@@jeskasper I put a sheet of metal under the jack so as it wouldn’t dig in and that it rolled smoothly. Also put wedges in to stop the front axle twisting. The main thing is when you separate the half’s try and ensure they part in a straight line and stays that way. You’ll appreciate it when joining them. I did it mostly on my own so it is not rocket science.

@jeskasper 2 года назад

@@tridbant wedges have been ready for a while. :) I only have a regular garage jack with wheels and a round lifting plate. I was thinking of making a length of 2x4 and put a hole in the middle for the jack plate, and then strap it to the gear box housing, just to make sure the tractor is supported and the jack doesn’t slip.

@tridbant 2 года назад

@@jeskasper the jack twisting is what misaligned my halves.

@TheKnacklersWorkshop 2 года назад

Hello Lance, Good video... I bet many used the bolts to try and draw together both halves... Cheers. Paul,,

@BundyBearsShed 2 года назад

You are right then the main clutch plate gets bent and you have to do it all again.

@Liamautomechanic 2 года назад

Good vid.

@BundyBearsShed 2 года назад

Thankyou.

@manfromthemist1958 2 года назад

Hi Lance, yet another informative video, great job mate keep up the good work, and while I've got you, I'm just starting to rebuild my DB990 AD4/49 engine following tips from your vid's, everything was going well until I replaced the rear oil seal(new rope inserted as per your vid) the crank was free until then, now I have to put quite a bit of pressure on it (by hand) but when it turns, its good, should I strip it out again or is this OK?

@BundyBearsShed 2 года назад

If the rope seal was soaked on engine oil it should be fine and bed in. I worked on the DB tractors for 9 years way back and still have some of the tooling.

@manfromthemist1958 2 года назад

@@BundyBearsShed Thanks for the assurance, the rope seals were soaked for a week and put in the holders in the same way as shown in your vid, and then on assembly everything including the crank was given a good coat of EP90, which Iuse as it sticks around for longer. Many thanks Barry

@NicoleThompson-oh6mk Год назад

Ive split my '54 ferguson tea20 apart to diagnose the reason as to why hydraulic fluid pours out of the weep hole on the front of the gearbox bell housing when the tractor warms up and comes to a stop. could you provide any information on that issue for me? thanks

@BundyBearsShed Год назад

Check the next couple of videos, i do one on the rear engine seal and another on the front grarbox seal that might be handy for you.

@spency787 11 месяцев назад

Hi Lance. I know this video is a little old but I’m about to tackle a ring gear replacement on my ‘49 TEA20. When you are doing the clutch test could you just turn the engine over with the starting handle instead of a lever bar on the ring gear itself? Cheers from 🇬🇧

@BundyBearsShed 11 месяцев назад

Yes you could for sure.

@cjx_ferguson5451 2 года назад

Good Job again Lance! Question for you the trick with engaging the gear to test the clutch with the flywheel does it also work with a TO35 or MH50 Assuming a to35 can be placed in 6th gear and follow the same procedure. I'm about to split one with a 6 speed tranny and I found that to be a really good trick.

@BundyBearsShed 2 года назад

Yes it works with any make I have found as long as it is not a powershift.