HOW TO | Soffit and Fascia (Part 2 of 2) 

A lot of you guys have asked me about tools and supplies in the past so I became an amazon affiliate and looked up the best stuff for you guys. In the description you'll find my favorite tools or the best deals I could find on amazon. check it out and let me know what you think. Be sure to check out PART 1 if you haven't seen it. I show you guys how to hang soffit in that one. Like and Sub to see more. Going to post the siding part soon

It's very kind of you to take the time to help people with your comprehensive videos. It's much appreciated. You should not stop. It takes many many years to build a channel, but you will be rewarded.

Very good video. Thanks for teaching your skills. I’m a retired commercial electrician that wound up in the Audio Visual industry and learned how to work with metal studs and tin snips way back in the day. Now I’m putting coil stock and vinyl on my shed. I’m trying to figure out how to cut an inside corner bend with tin snips and then saw you use the scribe and break method. You made my day fella. Thanks for your service to our country as well.🫵🏼🫵🏼🫵🏼👍🏼👍🏼👍🏼🇺🇸🇺🇸🇺🇸🇺🇸🛢️🛢️🛢️🛢️🛢️

Thank you for making these videos. Saving money being my own ‘contractor.’ Cheers 🍻

Thank you. You explain everything that needs explaining perfectly and unambiguously , and don't explain a bunch of crap that doesn't need it.

I have been watching your videos for the past couple days man and you are amazing keep up the work and thank you for taking your time to teach

Hey great videos man. I’ve done nothing but roofing and siding for the last 15 years and just like watching the way other people do it I do have a tip though. When running your facia over top of your bird box where are you take your knife and cut the bottom lip I’ll take a piece of cool stock and make a double half inch bend to make a hem and it locks right in over the raw edge. Mostly only do it when it’s over 18 inches but it really helps the metal lay flat and it gives a really good. Also when running that top piece of rake facia I just brought my tape to the soffit side of the peak measure to the bottom of my facia and then subtract a quarter inch pull your measurement to the top Burn an inch and a quarter for overlap market and cut 2 inches longer and then the mark on your lip will be a bend point that you cut away from the face and bend it down. It’s just A way to do it without scribing

Very good. Thank You.

This is wildy helpful. Thank you

A 10' aluminum break is a nice tool to have, if you can afford it

Where did you go man?? Your channel was starting to blow up and you disappeared. LET'S GO

All legit, the man does good work.

Awesome 👌 always open to new ideas & techniques

You can also make these bends using a piece of 2x4 or the customer's deck railing and a hammer, sometimes it is hard too find such tools

A metal awl (scratch awl) and hammer works well for punching holes through (even on metal roofs too, but with like fascia etc….not trying to do entire stack at once either), yes, will eventually be buying a new awl…..but can get a pack of around 5 for $4-$6, even w/ today’s prices😉. Also like the “trick” for at peak of gable end doing a few cuts to bend over the fascia so it’s one piece at the top, little more work though then just measuring and doing a scribe, miter, or straight cut….but everyone has their own favorite way; and that’s what makes things interesting, imo….seeing and learning from one another “ppl’s tips & tricks” that can help others out. Nothing wrong w/ trying something new and if find don’t “like or not your style”, than ya don’t do again and move to what were doing or try again w/ something new. ¹ Do AGREE that buying your material from Home Depot, Lowes, etc…instead from a supply “store” does make a difference, imo, as you stated and noticed in w/ this install. Seems to be better “quality” at certain places than others, which, again, imo….can make a difference in the install process; especially w/ time and fasteners used. Have a good one✌🏻 ¹ edited: b/c I added this extra comment (as an fyi to NE1, after a like/dislike/comment)

Good deal , great looking work brother !

Great video !

Thanks for the video 👍

everybody shows how to put ice and water shield on OSB. But how do you handle tear off when it has non removable ice and water and you don't want to waste too much time on it..DIY

Nice work zach

Where you been at man? Are you locked up? Lol jk Post once a year. Great content respect. From a 🇨🇦

Hey Zach I’ve been watching your videos for a few years now, I’m only 20, but I started roofing when I was 14 and over the years I saved up, bought tools, and really practiced my trade… I bought a nice looking clean truck, and I’ve been working for myself for close to a year now and I’ve been staying afloat but it’s still basically paycheck to paycheck, can you do a video giving advice on finding work, starting a business and how to be fruitful… I know it’s mostly experience, but I just wanna hear what someone who actually works has to say on the topic

Woow amazing,⭐⭐⭐⭐⭐🔥🔥🔥💥💥💥👏👏👏👏👏👏

Great video though man!

Good job

Good

I had a piece of front fascia metal blow off in a big wind storm the other day, I can’t seem to get it to slide back under the drip edge, any tips with that? Or just pry it up with a screw driver?

I am installing flat roof flashing under shingles and over corrugated patio roof. Seems most city codes require roof flashing to be 26 Gauge (0.019 inch). But the flashing rolls sold at Home Depot are thinner. How do I resolve this?

How do you go about pricing a soffit and fascia job?

Galvanized staples?

Any videos coming out? Your been missing for a while and would love some more videos

Hey man i love your videaos dude you have tought me a lot of things that i cant wait to try on the roof. Unfortunately its January in New York and shingle roofs are few and far between. I was wondering if you do medal toofs as well? Also I would like to actually talk to you about the roofing olympics. My buddy whos name is also Zach has his own company and is incredibly fast. Honestly i think it would be pretty damn close between you and him. Its cool that your doing that shit none the less, im glad you're trying to bring people together.

Can we get some different types of valley installations and how to shingle a hip

Where u been?

What do you mean @ 11:19??

Looks good. But that drip edge looks bad. Those corners are a eye sore and for sure gonna leak and rot that fascia board out.!!

If your covering your facia with gutter,why nail the bottom? You can nail or screw in the middle where the trough would sit and hide the screws, also where I’m from we don’t trim nail the gable facia the weather usually rips it off no matter if we nail the face or lip

You must of installed a billion shingles in the last 300 days 😂

Do you use ss staples? What size do you use for fascia?

Where is this dude at

Hello, do you have a Patreon page or some other way to ask you questions? I have to put a roof on a small house that used to belong to my mother, and though your videos are a great help, I still have a question of two to that specific project.

Where you at???

why did you stop posting?

How's the hypothyroidism

What's your service area ?

Post more videos bro

Wow you are still working on the same project, shit this is taking you 5 years to build 4 walls and a roof

He

Hello Veteran Construction! We love your content, and we would like to chat further with you. Do you have an email address where we can reach out? Thank you!

U still alive buddy

What happened to you bro

U must b gtn gd numbers to waste time on this unecessary measures. Why would u use that prefab fascia? Do a z bend for porkchop create nailing falange to wall then box out. Alot holes in ur game dude

So you're no longer in business due to personal health reasons?

I know that’s how they do it in some parts of the country but that pre made fascia is ugly and cheap looking. I’d rather scrape and paint than to have something like that on my house.

Shame on this channel looking for more vids, but what he teaches is all wrong

fascia it called fascia metal of alum fascia not gutter apron your to funny honey

yo why yo be cutting dwn a 24 ft plank .my sweaty?????????me reamber lover never sweat the petty stuff but alway pet the sweaty stuff

Pure garbage, material and workmanship.

I’m missing your videos