Thanks that help alot today ! Sunday today and I still have all my work uniforms to wash and my machine play funny today 😄 not good😅 I glad people do this videos to help us 👍
Hi There Thank you for your replay .... However the Zanussi lindo 300 we have is a 9Kg a Intermittent spin some times not all times so Please any where can you please send me link where i can buy the parts required saying that i have a spare mother board.... please let me know as really is obsessing this problem . Kindle thanks. Joe
My Lindo 300 drum smells horrid. I am wondering if it is draining properly. The drain hose currently extends up above the height of the machine before dropping down into the standpipe. Is pumping above the height of the machine likely to cause drainage problems?
According to another RU-vid video, to unblock the drain pump, you have to turn the machine on its side, then unscrew the pump from UNDER the machine, clean it and replace it. That's assuming your machine isn't draining.
Er..cry. because there is no way to drain the water from the tub. The only slim chance you may have is between 2 or mabey 3 people. Pull the machine out. Put the drain hose into a bucket and 2 of you carefully tilt the washer backwards. I think there is emergency door release but I need to investigate further myself.
Hi. My lindo 300 10kg model is not rinsing properly at all on any cycle. I use one ariel pod even when the washer is full. I never use two. It's usually on a towel wash or bedding wash ( 60c ). I have extra rinse option on and still there are loads of sud residue left during the final spin. I run a hot 90 degree cycle with nothing in it once per month and use Dr beckman cleaner every 90 days. Still no joy? Any ideas please? I love this machine and it's only three years old. Thanks :)
Is it draining fast enough? If its connected to sink spigot these can create drainage problems. So check that the end of the hose and spigot is clear of gunk. There is also a inaccessible filter to the general public attached to underside of the wash tub. Which can be removed cleared and re-attached by a competent person.
@@whichwasher2007 hey now that you mention it sometimes it sounds like there is a drainage lag and when spinning you can hear the laundry sloshing in the water for a bit. Drain pipe is in a regular stand pipe.
I started doing this and before it started I got E11 error so I moved it check the pipes at the back nothing and then a did this again, I got right the way to the ELE test and it didn’t feel warm when I touched it the the error E11 again .... help! (It’s only 5 months old)
Hi there. Thanks for the video. I've been getting an E10 error - which is a problem with water coming in. Regular cycles give this error but it fills fine when I put the machine on rinse only cycle. I put it in diagnostic mode like in your video but the first test (pressure switch?) when it's on 30@30 light does nothing but then when I carried on to the next test (direct fill/led at Cottons) water came in fine. The rest of the tests seemed to work fine. Any ideas please?
Faulty fill valve. It has 2 of them. 1 for direct fill. 1 for main wash dispenser fill. Both combined for fabric softener. Main wash 1 is stuck closed.
Apart from the difficulty of understanding the accent and speed of each step, why oh why must we have that bloody awful music in the background. If I want to listen to music I'll go somewhere else.
Hi there, just looking for a hudge help i have both a zanussi lindo300 at 4 years a go since then the machine is working good for the last 5 months is showing a e05 meaning iss a erro 5 we done all posible . now te machine is not spining at 1400 or 1200 even 800 i even both a mother board with the cost off 180£ and still the same. Now when i reset fowling your video wee can clear the erro andd ssshow no erro probleme is not spining at any speed. I have contacted zanusssi anddd i cant get any where, so the help line is crab, do you can you help with this issue?
No. But it's much simpler on yours. Push and hold program and temperature buttons together while pushing the power button. And hold untill the leds start cycling through. Then use the program button to select functions.
whichwasher2007 When I do as you say it just comes up as error and turns off, are you sure these are the right two buttons to hold down, thank you in advance