100% correct. I got a Joyo Overdrive, a TS clone. when I put the noisegate after the tuner or after the guitar and before the OD it is much much better. Especially for metal.
Try this method: Connect guitar to input of ns2. Output to input of metal zone. Output of metal zone to return of your fx loop. Pedal itself is an insane preamp... sounds 1000x better used this way than in front of amp.... Honestly, its the best way to get full potential from that pedal. I learned that tip from Ola Englunds video on the metal zone.
I've heard that, but then it nullifies the rest of your fx loop. You can make the MT-2 sound fine in the front of the amp, especially with an EQ in the mix.
I've found using one at the front in between the guitar very delicately and one after your gain stage be it an amp or whatever in front of ambient pedals works best for me. But I didn't know about the four cable method.
I wish I had the NS2 for that particular 4 cable method. For metal, the gain really amplifies the clean signal and putting it after the drives gives it a lot to deal with. So I always put it before the drives. If I ever get a second noise suppressor I'd put that one after the drives but with a slightly lighter threshold.
The decimator is really plug n play but that definitely comes with a price, the boss NS-2 can really work well but you’re gonna have to use a 4 cable method which if you factor in the price of a couple more cables (assuming you already have an input cable and an output cable) you’ll pay a little over half the price than just the decimator on its own
So if you're not using an fx loop, I would put it right after the gate. If you;re using an FX loop, I would try it both in the loop and before the amp to see which one sounds better.
I know this is 2 years old but hopefully you'll read this. How about this scenario? My amp has an effects loop and pedal chain is set up in a normal configuration. Tuner, wah, fuzz, boost, od in the front. Chorus, phaser, reverb, delay in the loop. Using 4 cables, wouldn't I run from guitar to gate input then gate output to tuner? Then the rest of the chain going to front of amp stays the same. Then run send from amp fx loop to return on gate and send on gate to return on amp?
You can try it that way, but you'll find the above scenario is the most common with the NS-2. Sometimes it's called the X method because it gates the guitar clean signal and preamp noise by being able to identify them both. I know it sounds weird, but it works. Try it both ways and see which sounds best for both your tone and noise suppression.
@Guitarnivore I think I get it now. This way, it's basically the same method as isolating a pedal with the loop on the gate, but now you're including the preamp section of the amp and whatever is in front of it in that loop. If you don't mind another question, what about delays, phaser and such? Should I place them before or after the gate? I don't have a gate yet, still deciding between Boss and TC's Sentry. Thanks for replying man, I appreciate your help.
Do you have to use 4 chord or wet dry wet or stereo method? Or can you just do a real simple set up? Will it get rid of say, hum, string noise or the little clunky noise like when changing chords etc..I dont play high gain, I just go for huge loud crunch tone, as much as possible with a simple set up with maybe 5-10 pedals.
You don't have to, but if you have the means, it seems to be the best way to quiet everything down. If not, and you're just trying to quiet some 60 cycle hum, try putting it at the beginning of your fx chain and adjust the threshold. I like to use my NS-2 on mute mode, so it keeps everything quiet when it's no engaged and I can completely mute everything my engaging it. If you find what works best for you and your rig, go with that.
Sometimes it's called a power in, but it's basically the receiving end of the loop's signal. Your guitars signal gets sent out of the power out/Send of the FX loop, goes through your pedals and then returns to the amp to be processed and sent to the speaker. Does that answer your question?
So, your signal essentially is being suppressed twice? First the guitar and then again after the distortion pedal and amp? Where would you run your wah in that chain?
I like the video, very informative, and I also have the boss ns2 and the metal zone, and I have it hooked up the same way you instructed, but say I have a multi effects pedal, how do I hook that up in the chain? On the diagram it says hook up here, with an arrow, but... I may be stupid but how do I hook it up in the chain with effects loop an all that
Sorry I took so long to respond. That's a good question. I would run it in the loop, but depending what you already have in the loop, you may want to place any time FX after it, otherwise it might sound a bit funky. But I would run it between the NS2 and the Send. BUT, if the multi FX unit has it's own noise suppressor, maybe run the NS2 between the guitar and front of the amp. That way you kill any noise coming from your guitar AND in the loop. Does that makes sense?
Wondering where to place my gate got a tc sentry using an high gain Savage Drive od/ high gain distortion a looper pedal and rechecho using 4 cable method into a multi effects pedal. Just got it all working together the gate is at the end of the od/distortion and start of the effects loop.
That's a good question, considering you are already using the 4 cable method elsewhere within you chain. Does your mulit-fx pedal have a built in noise gate of it's own?
Hi my name is Roberto, I have stepped into the magical world of noise reduction. I would like to buy a noise gate for my pedalboard. My Santana-like sound needs a noise gate but also needs to have good feedback with my MesaBoogie. I'm worried that the noise gate will cut the sound too much and the feedback will go to waste. What do you suggest?
That's a tough one, Roberto. See if you find this article of any use. en.customboards.fi/pages/get-rid-of-that-noise-the-different-uses-for-a-noise-suppressor
Good demo, but the pedals aren't noisy, it's always your guitar. If you have an actually noisy pedal it's defective. A gain or boost or distortion pedal just boosts the signal it's getting and the noise it makes is it just doing its job.
I have to definitely disagree depending on which pedals Your speaking of and the order they are placed, buffers etc. Are You telling Me that amps are not noisy as well and that it’s just My guitar? Just wondering
@@adamstein9333 Yes it's just your guitar. Pedals and amps are not supposed to add additional noise, if they do they are faulty. The noise gate was literally invented to filter out guitar pickup noise, it can work for bad pedals but that is not the intended use. If you want a noise gate for your guitar and your bad pedals, then get the EHX Silencer. It has an effects loop that will allow you to apply the noise gate to your pedals.
@@sbesbesbe Yes I have a AMT R2 and a Tubescreamer Clone that are Very noisy together especially but compliment each other very Well at the same time. When paired with other preamps I have no noise at all, and I’m using a Chapman ML3 Pro Modern and A Washburn Paralaxe and Your making Me extremely paranoid lol! I’ve notice a lot of amps these days (the modelling ones) have crazy feedback, and stacking pedals can have very noisy results no matter how noise cancelled Your pick ups are. 25 years ago I bought a Gibson SG Standard off the rack at guitar center (main problem lol) that had a screaming noise as loud as the guitar signal and was for sure faulty, which was replaced with a Toni Iommi that actually was worse than that, so I took the old bridge probucker from My Sg special and that solved it. I totally understand that argument, but should I return My pedals because they are defective? Isn’t that what noise suppression pedals are for? Or just for people with defective gear?
