Important note! We have received a lot of comments to not use the foam brush due to reasons that any physical contact is not great for the paint. Plus, there are too many variables to control including a poorly maintained foam brush, foam brushes that are made from hard plastic bristles, other particles that may not be easily removed from the brush by spraying it. Thank you for the comments. From dirty microfiber cloths and wash mitts to snow brushes used to clear snow to driving at highway speed in sandy conditions to foam brushes and more, any thing or particles that come into physical contact with the paint could potentially cause the paint to get swirl marks or micro scratches depending on many variables. The aim of the video was meant to familiarize people who haven't used the self-serve car washes before. Hopefully it achieved its goal to demystifying what is involved in using one. Though a 2 bucket method would be recommended for the ultimate care of your paint, most car washes don't allow you to do this since it takes up a stall without payment to use it for the full time you are there. Plus, in the winter zones where temperatures get below 0°C you can't wash your vehicle at home on your driveway (If you have one). So, if you want to treat your cars paint with the most care at self-serve car washes, then it may be best to use a touchless method to wash your vehicle at the self-serve car wash. In the past, we have had issues getting the vehicle fully clean with just a touchless method and was a reason we use the foam brush (one that was cleaned by us, expels a lot of foam soap and was made of animal hair, not synthetic plastic or rubber and used lightly). It helped to remove the fine dirt film/residue that gets left behind. To treat our paint the best going forward, we have recently been trying again with a different touchless method and it so far is working better. More testing needed, though. The new method we are testing: 1) Start the wash using the high pressure soap or rinse from the wash wand to rinse off all dirt and debris from your vehicle. Focusing more time on really dirty areas. 2) Use the foaming soap from the wash wand (Not the foam brush) to dispense soap to cover the entire vehicle and wheels. 3) Stop the timer to stop the charges and to let the soap soak for a few minutes (You can go as long as you want). NOTE: We don't use the Pause function since it still counts the time and continues to charge. You may need to experiment because there will usually be an initial, higher startup cost to start the wash. 4) Start again, using the high-pressure rinse from the wash wand to rinse the entire vehicle clean. Starting from bottom to top to help ensure no sections are missed, then rinse top down. 5) Dry using a large clean microfiber cloth. 6) Use spray wax to finish. Of course, use whatever method you are most comfortable with to wash your vehicle. Don't forget that all car washes are different, with different quality and condition of equipment and soaps. Some are maintained better than others, which could give varying results. You can also consider testing the soap with litmus paper (pH test paper) to check the acidity. Let us know if you have any comments or suggestions!
Great response! I literally went to the comments right after you used the brush and I’m glad you wrote this. Yes, there are too many variables, but bringing your own wash mitt and drying towels is what I always recommend. Yes, any sort of contact mars and scratches paint over time, but the goal is not to never touch the paint. It’s to minimize swirls and scratches by proper equipment and technique for each wash. Wash mitt recommendation: - The Rag Company Cyclone Ultra (Amazon) Drying towel recommendations: - The Rag Company Liquid8r - The Rag Company Double Twistress (Both on Amazon) When washing towels and wash mitt, I would recommend using a dedicated microfiber detergent. Regular laundry detergent reduced the absorbency properties by clogging the fibers. I recommend P&S Rags to Riches for washing. Dry on low or air dry. Higher temp melts fibers and ruin the towel making it unusable for being safe on paint.
I was literally about to comment this, interesting to see you still commenting on your old videos. I went to a self service wash today, saw that brush, and didn't even try it. I could just sense the evil and dirt. I come back and watch this video and read the comments. I see many people feel the same way... lol
Shout out to all the people who are here because they’re terrified of looking like a clown trying to use one of these car washes for the first time. We’re all in this together.
Yup I've been postponing my first car-wash experience for days now because I'm quite terrified to look like a clown, especially since I got a nice car finally :D I've decided to go late at night when there's barely anyone and figure it out in peace.
Just used my first self serve carwash today and decided to only use the foam brush on my wheels + tires. My wheels are so shiny and my car looks fantastic. I've never been so satisfied with a car wash.. FOR HALF THE PRICE. And it was fun to do it myself. This might become addicting and it'll be atleast a weekly thing for me haha.
This is the video I've been looking for. Clear, concise, and easy-to-follow instructions help take the mystery out of car washes. For years I drove a 2005 grey Corolla. It was a workhorse and I liked it, but I just picked up a brand new VW GTI and for the first time in my life I found myself suddenly concerned about car washes! This was a huge help. Thank you very much for the time and effort that you took to make such a quality guide.
You're welcome. Thank you for the nice comment and for taking the time to give us feedback. I used to have a 1997 Corolla. Very reliable cars indeed. Please subscribe to our channel and share our videos. We appreciate your help in helping our channel grow. Have fun with your new car! 👍
That's why I will use the wand on rinse/pressure wash and spray it out way before it touches the car, but that man has a glorious amount of soap out of the brush, where I'm at it is 8 bucks, unlimited time with all the tools wax, vacuum etc spent 2 hours there.
To avoid foam brush, use foam brush setting, gently put foam brush on the body of car to just use the foam. Put foam all over ur car without dragging the foam brush. Use your own wash mits to clean the car using the foam spots uve created.
Thanks for the tip. A good idea for those that want to avoid the foam brush like the plague. In that case, also bring buckets with grit guards to clean the mitts between panels. Pre-fill with clean water/soap at the car wash
@@BuhnanaFone I mean it makes sense… don’t use the brush as well, the brush. Just get the foam soap from it throwing it on your car then use your own mit or cloth to wipe it
Thank you for taking the time to provide such positive feedback. We really appreciate it. If you know anyone else this might help, please share our videos with them. We're trying to reach our next goal of 10K subscribers.
Please, PLEASE do NOT use the foam brush or any brush/sponge on your car. It will cause swirls, scratches, etc. use a microfiber wash kit and rinse it after washing every panel
Not all brushes are bad. Majority are (synthetic fiber ones) but Animal/Boar's hair brushes are very soft and are good if used properly (They hold a lot of water and foam and dirt and release easily when rinsed). If people use a good wash mitt and rinse it after washing every panel, then it can also be done to the brush to rinse or flick the new foam off the brush. Note that the car wash animal hair brushes have new foam regularly pushing out of the brush to push out the dirt and debris. Notice how in the car wash I was at, how much new foam was pushing out. This is also important. Flicking and lots of new foam coming through is similar to rinsing off a wash mitt. I also indicated to use the high pressure soap to properly spray off a lot of the debris on the car before using the foam animal hair brush. This gets most of the dirt off and also wets the paint surface. I also indicated to lightly scrub and regularly flick off the dirty foam (This can be done multiple times during, within and after each panel). I suppose if anyone is paranoid, they can bring a bucket with a grit guard and dunk the foam brush in after every panel. Here is a thread with people that haven't had issues with Boar's hair brushes. The OP was originally upset at the results but it was due to method of use. www.autogeekonline.net/forum/auto-detailing-101-a/18179-montana-boars-hair-trashed-my-finish.html Hope that clarifies things.
That's why it's important to clean them properly before you use and while you use them. Same thing as a wash mitt that is used with 2 bucket method with a grit guard. It has to be clean before use and also during use.
Frakking Creations dirt gets stuck on them then it scratches ur paint so you should pressure wash them about 10 times in a wash depending how big ur car is
Thanks for your comment. For anyone that is worried about this can of course do more flicking of the foam brush to get the dirt off the brush. Remember that new foam (and a lot of it) is coming out of the brush at the self-serve car washes. Not something that home foam brushes have. You can also, do what you recommend and pressure wash more frequently between washing panels. Another way is to bring a bucket with a grit guard and wash the brush as you would a wash mitt after every panel.
@@nibbax7772 Wash it out and the little tub of water it sits in first. You can always feel it for any grit. The real horsehair ones are quite soft, they also use that in higher end paint brushes. Good ones are always pumping out foam and that pushes any dirt out of them as well.
Thanks for this video! I just moved out on my own and have been watching "how to be an adult" videos, lol. Like I had to watch a video how to use a garbage disposal because my mom taught me wrong lol, and I watched a video how to do laundry because I didn't know if you put the detergent in the machine before the clothes or on top of the clothes, or do you put the detergent in that hole on the side, lol.
You're welcome. Glad our video was helpful. Thanks for sharing your story. It definitely can be a big learning experience when you first move out on your own. One of the reasons we do the videos we do is because as we learned things on our own we also found ourselves saying we wished someone had told or taught us sooner.
Here are the 10 steps I follow: I take two buckets (one with soapy water and one with just water) lots of drying towels, 3 microfiber mits (only need 2 but one extra in case you drop one), portable pump foam sprayer, soap, wheel cleaner, spray wax, and tire/plastic trim shine. Step 1: high pressure rinse Step 2: use your foam sprayer to presoak your entire car and let soak for 5-10 min. Step 3: clean wheels with your fav wheel cleaner while paint soaks. I like to use the brush method shown in this video for wheels only. Rinse brush after each wheel is clean. Step 4 (optional): rinse car again and reapply soap from foam gun Step 5: wash paint with micro fiber mits using two bucket method Step 6: high pressure rinse Step 7 (optional): spot free rinse Step 8: spray vehicle with your favorite spray wax/quick detailer. Step 9: dry vehicle from top to bottom Step 10: shine your wheels and exterior plastic trims if applicable. Now you will have a scratch fee experience, and will never wash your car another way. Happy detailing fam! :D
Cost will depend on how many minutes you use and what their cost per minute is. For the ones I have used, you can pause the water/soap but the timer keeps going which is dumb. But you can always stop the wash and restart it when you are ready. Just note that they typically have a higher charge to start the wash which is usually more than the per minute cost. So plan your washes and that should help you spend less.
@@Thomashorsman It doesn't matter if the brush was washed, real car enthusiasts knows not to use those brushes at self-served car washes. A lot of Yall clowns don't know how to wash a car correctly without damaging the paint.
@Xachary Zealot That's cause you ain't there and it's not outside in the Sun. Once it's parked and the Sun hits it, he'll start to notice all the swirl marks in his paint.
I tried using the foam brush even with the cleaning/flicking technique before using it and still left a bunch of swirls on my clear coat and lost significant shine on my car. Would NOT recommend it at all.
yeah the self serve in the video was really nice. My local one has some questionable brushes so I always try to go when its empty and just sneak in a bucket and some microfiber towels haha.
This is the same method my old man taught me. I miss the good old days of 50 cent Tuesdays at the car wash. This may not be for everyone but my tip is rinse with the wax or clear coat protectant setting on the spray gun.
Thanks for helping the ladies out. I feel more confident about washing my car tomorrow. I’m so tired of letting others wash my car and not thoroughly cleaning or drying.
I'm glad they're helping the fellows too 😂. I'm always so unsure if I'm getting bad service when I don't know how to do it myself. Now I probably will always do it myself
I gave this video a thumbs down because you NEVER use the brush on your Car. No matter how much you clean it , it WILL leave scratches on your paint. If you love your car, you will never use that brush
You're welcome! And great job. 👍Glad you were able to get great results. Thank you for taking a minute to comment back. Please share our videos with friends and family if you think it will help them too. We appreciate your support in helping our channel grow!
I tired this with a brand new swirl free rental car cleaned the brush off and did just like this, took the car out of the wash inspected the paint and guess what I found swirls everywhere good thing it was a rental 😉 and that’s why I will never use that swirl wand on my personal black car 😁 well actually I do use the brush for my floor mats, engine bay and wheel wells the only thing it’s good for lol
Simple instruction but still have the details that matter. I like the ‘wash top half first’ tip and also the ‘stop bebore the minute end’ to avoid getting charge for the next minute :))
Thank you for your comment. Appreciate you taking the time to let us know! :) Please share with anyone else you think it will help! We want to grow our channel to 10K subs by year's end.
Thank you, just the info I was looking for, other videos didn’t mention the wax. I had no idea what I was doing whenever I went to wash my car, all I used was soap and rinse power wash.
Please Note: You have a fourth option, a rinseless wash. I use Optimum No Rinse (ONR) for my weekly washes all year round, even in the winter. I agree with you, NEVER use an automatic car wash. If you have to use a self-serve car wash, NEVER USE THE SOAP AT A CAR WASH, I would recommend a PH neutral soap, such as Meguiars or Turtle Wax, available at any box store or auto parts store. NEVER USE THE BRUSH AT THE CAR WASH, you never know how the brush was used. Bring a soft microfiber towels, brushes or wash mitts, etc. with your own soap. For professional car detailing videos tricks & tips, I would recommend Brian from Apex Detail or Pan the Organizer. I have been cleaning cars for 45 years, and I still learn from Brian and or Pan HAPPY CAR CLEANING!
Stay away from the evil Foam Brush👹 if you truly love your car just buy a wash mitt or car specific sponge to scrub with soap. Even Rinsing the foam brush prior to use won’t guarantee not scratching your paint job
Thanks for the feedback. Part of my problem is that when I bring the car to the dealership for warranty and such, they wash it. I don't think their employees take the time to wash properly or use the 2 bucket method. Plus I also noticed they have a spinning cloth automatic wash that wash used on my car the last time I brought it in. Unfortunately it was already damaged by the dealership before all this.
Another reason not to use the bay brush is because it costs $$ during the time it’s used. Bring your own buckets and mitts, and pay only for the soap before and rinse after!
If you're using a brush on any part of the paint, you should not be providing a tutorial on how to scratch, Mar, swirl up the paint. This was horrible.
Makes self service car washing look a lot easier and less intimidating to do now. Thanks! Oh and how much time should be set aside for the whole process?
You're welcome. Thanks for commenting. How much time depends on how good you want the results to be, how much money you are ok with spending and also how dirty the car is to begin with. We usually take 15 to 20 minutes to do a good clean. You can experiment to find out what works for you. Some people only need about 10 minutes. Add additional "free" time for drying and waxing if the car wash isn't busy. They don't kick you out when it's not busy and you have already paid to wash.
I'm not a big fan of those self car wash liquid waxes. I find that the self application like I showed in the video to give better results and last longer.
Never use the brush. Not only can it have dirt in it, but the bristles are too abrasive. If you wouldn't use it to clean your glasses then don't use it on your car.
Umm I operate carwash equipment, and microfiber is not foam and much less volatile than doing it yourself, and even doing it yourself will cause swirl marks if you don't wax
4:32 because you will get swirl marks on your paint/clearcoat. sure you can clean the brush and it may be free of dirt and contaminants, but the brush itself is rough, it shouldn't be making contact with the paint or you'll get swirl marks, it needs to be a soft plush wash mitt for the actual scrubbing part. i would use the foam brush to just foam up the car, but i'd bring my own hand wash mitt to actually do the scrubbing. unless you have an older car with imperfect paint anyway then it's not a big deal i guess.
It’s not just the stuff that gets caught in the brush that is bad, the brush is not safe. The brush is too abrasive for the paint and it will cause swirl marks. Do not use it and you’ll thank me later.
Can you opt to not dry with a microfiber towel but just drive around and let the airflow dry the car? Will that leave any streaks, residue, or watermarks behind?
I wouldn't do it since it will leave streaks. The streaks can be from the water drying and leaving mineral deposits but it will more likely come from sand, dust and dirt in the air and on the road blowing up around the car and sticking to the water and then drying onto the car. Hope this helps.
Thanks so much! Hope you enjoy using the self car wash going forward. We would love to have more Canadians watching our videos but get more from the US. Please subscribe and share our videos if you haven't already. We appreciate it!
This is pure cringe for me. They used a broom for a nice merc do not use this video just get your own buckets and microfibres then wash ur car. Do not use this vid.
I provide my reasoning in reply to Luis below... Also, not everyone can wash their vehicles outside, especially when in the winter so self-serve car washes are needed. And generalizing the animal hair brush as a broom doesn't make this method invalid. For those that are totally against, you don't have to use the animal hair foam brush. Bring a wash mitt and 2 buckets with grit guard. All the other tips are still valid even if you disagree with using the foam brush.
Thanks for commenting. Here's my thoughts on this. There are at least 4 things needed when washing your car in order to prevent scratches to the paint. Good wash tool, water, soap/foam and technique. Without any one of those 4 you will scratch your paint. I'd like to see someone use the best microfiber cloth out there and clean the paint without water, soap or good technique and not scratch their paint. I wouldn't use any regular brush. Do not use synthetic hair brushes as those are very harsh. Animal hair brushes are best. They must be in good condition, clean, with long hair bristles and wet with a lot of soap/foam before use. One thing that the self-serve car washes have that you don't have at home is the foam brush that continuously expells soap/foam. This will continously push dirt out of it and provide new soap/foam. See how much comes out from the one in my video. I wouldn't as easily recommend a foam brush that you use at home that doesn't do this. The water and soap will start to dissolve (a little) and wet the dirt and lift the dirt from the paint surface. But that's not enough to clean it. That's why you still need some physical washing... hence the microfiber cloth/wash mitt most recommend with 2 bucket method. Though, in this case we're using an animal hair brush. The water softens the animal hair brush much like what happens when you wet your hair. The soap/foam is also an important factor because it helps clean but more importantly, suspend the dirt that is washed off. The water also helps in this. That's why the best microfiber cloths are made to hold a lot of water and soap. As mentioned before, the self-serve car wash brushes continuously expell new soap/foam. For technique, I mentioned to use only light brushing. But this is after most of the dirt particles are washed off by the high-pressure soap in the 1st step. A clean tool is needed so washing it at the beginning with high-pressure soap does a good job of that. Through-out the washing, the new foam continues to come out and the flicking is to help remove the dirty soap. I suppose, for anyone that is worried, the technique can be made better by different ways. for example, 1) using the pressure washer to rinse after every panel 2) bringing a bucket with grit guard and using it to clean the brush like you would a wash mitt. 3) using similar wiping technique like you would with a wash mitt Technique also includes more frequent washing. Just as dirty underwear that isn't washed for 1 month of wearing will take more washing to clean, washing your vehicle not frequent enough leaves more stubborn dirt particles behind (and baked on by the sun) that need harder scrubbing which will cause scratches. So don't leave your vehicle too dirty for too long. Hope that clarifies my reasoning.
You can always just use the high pressure soap and then rinse but you may not be able to get all the fine dirt off. It would also depend how dirty your truck is every time you wash. More frequent washing could make it possible to just use touchless. I think just dripping the foam from the foam brush could take a while so not sure you want to do that. The car washes do have a low pressure soap you could use too but you will have to see if it outputs enough soap for you.
This is exactly what I was planning to do. The brush scares me, even if my car is a 90s beater. Just, the paint still looks nice and the brush seems good for if you got a mudded up truck, but if you have a nice car with dust, then just do that.
The bottom area of the car and the wheels pickup the most dirt so it's fine to scrub with the foam brush here, especially if you have a body kit. For the rest just drizzle foam everywhere without making contact. Then rinse. Easy peasy in and out. Good video though. Thanks for putting in the effort.
Or do what I do and bring a laundry basket full of my micro fiber towels, microfiber wash mit and sponge and my foam cannon. Spray a coat of my foam cannon on whole car first. Use the free light rinse coming out of the wand to wet the whole car. Do the high pressure soap, high pressure rinse, wax, then spot free rinse. Finish off with microfiber towels only allowing the weight of the towel itself to make one pass then flip. I go through 8-10 towels a wash. Then instantly throw them in my basket to be washed separately than anything else. No pain no Gain. I invested in a nice car there for it only made sense to invest in keeping that car looking good
what is the purpose for the first step, the second step seems to be enough soap to clean and the the third step would rinse all the dirt and soap off, right?
Good question. The first step is to loosen, dissolve and remove as much of dirt from the surface as possible. Especially the larger dirt particles. The reason is that larger dirt particles left behind can potentially scratch the paint as you use the foam brush.
I would love to own a car wash business like this however here in America people don’t wash there own car much they use the drive through car wash. Seems like truck users use these most. Btw great tips that I over looked in the past.
The only time I’d use a wash station like this would be for a work van or maybe if I Can’t access water and I need to wash a car prior to polishing. Nice tips tho
I live in a valley surounded by Amish cornfields. It gets really dusty down there. I live there with my parents. I don't give a damn about my car, but My Old Man washed his Jeep Grand Cherokee about every other weekend. He passed away last year. Recently I've been having to drive his old Jeep around to take my mother places. That thing ended up looking terrible. Oh, I should mention the Jeep is Brilliant White. Just took my mother to the dentist this morning, so I thought I swing by the carwash just down the road. It was $3.50 for 4 minutes! But thanks to this vid I didn't spend more than $10.
Yeah you really do have to be sneaky about it. 🙂 And if you're a regular and it's not busy, I'm sure they're ok with it. We always dry and wax inside when it's not busy.
As long as you’re paying for the time, it should be iight. I think the problem comes when people pay for a minute of pre-wash and then pay another minute for rinse
Great video, for me i just wash my car every two weeks at home. I would not take it to those automatic washes or self serve. but i i went to the self serve, i would bring my own wash mits and brushes. And contact wash is must, u cant just clean the car just by spraying it with soapy water, that removes like 65% of the dirt stuck on top, i would also use an iron remover as well as tar remover by spraying carpro tri-x. And wheel inner barrels must be cleaned too
Thanks for sharing your experience. I too have found that the spray itself is not enough to remove all the dirt. Usually, there is some residue left behind that you can't see until the car dries. The self serve car washes are needed for some because some people don't own a house and in some cases, even if they do, they cannot use the outdoor hose in the winter.
There are so many things i want to comment that are wrong about this video, especially regarding how to treat your paint (a brush scratches the paint, dont apply pressure when drying with a towel, so much misinformation). If you really want to learn HOW to wash your car, go watch ChrisFix' videos on how to super clean your car. I dont think this video is good for anything but to see how to control the hoses on american self-serve washes.
DO NOT use the brushes, idc how intelligent this guy sounds when making this video. Anything on that brush will scratch your car, and simply cleaning and washing the brush will not always do it. It’s a risk.
The brushes are filthy and doing a little rinse off, especially with the brush on the dirty ground, is not going to clean it. Anyone who wants to really know how to wash a car should watch Chicago Auto Pros.
Good video! Is the best way to wash the foam brush just to lay it flat and spray with high pressure? Do you ever use the ‘wax spray’ available at car washes? Thanks again for the video!!
You're welcome. Thanks for commenting. Checkout my pinned comment as I don't use the brush anymore and talk about that there. I typically don't use the wax spray at the car wash as it's more cost effective to bring your own and you can get much better ones. I linked to a few in the video description so choose one that suits you (synthetic, ceramic graphene)
This is a great guide. Just washed my car after watching this video and got pretty good results, did need to scrub a bit more with the foam brush in some areas but otherwise it was good. Also i like to go fast to dry the car instead of towel dry
Thanks for taking the time to provide us the feedback. We appreciate all the comments we get. We're glad that it helped you! Please share our videos if you feel it will help others. It'll help us know we're making the right videos. Subscribe and stay tuned for more great content in coming weeks.
Yeah, that is a valid concern. Thanks for commenting. We get a lot of comments on the brush. Even with a wash mitt you can scratch the paint if not used properly with good technique. If you use these brushes with good technique and light pressure (after high pressure washing the large dirt off the paint) it is possible to clean without damage. For those that are worried, they can use a scrubbing technique more similar to that of using a wash mitt and 2 bucket method. Note too that these brushes I showed also pump out a lot of new foam as you use it. With wheels I think it would depend because some wheels now come painted and that paint can get scratched too. I show one technique and the video provides more tips than just the brush, so hopefully it is helpful. Not everyone wants to spend hours doing a car wash. These car washes are needed and useful for those that can't wash outside (when in the winter) or have facilities and in the end it's up to the owner how detailed they want to be.
I've never touched the paint of any car I've owned and they all sparkle afterwards as long as you use the spot-free rinse and super air shammee to dry. A spray-on wax is a good idea but not required. I've never seen dirt or streaks after washing and drying. In any case, I'd rather some streaks over risking a scratch on a $15,000 paint job anyways. My paint will always be a virgin.
I just used the foam brush in same manner on a rental and didnt do any additional damage. Afterwards I applied QD and waxed it with sprawy wax - looks impressive and there is no additional swirls or scratches really. Spoke to the owner of car wash - they replace the natural brush often, but he also recommended pre rinse of the brush to ensure there is no grime in it. I will test it on new car which I’m picking up next week! I think more scratches are caused by people doing touchless and then wiping dry.
Don’t use their shine or wax, it will take off the paint in time. I heard about this 15 years ago. Tried it and sure enough the paint started coming off. Use your own shine and wax like here.
Oh, very interesting. In my city (another part of the globe) all self car washing stations are outdoors, so people usually only use them during warm weather. I think it's very cool to have indoors one.
Thanks for sharing. I've seen some new ones around our city that are outdoor versions too. The indoor ones are nice for when it's sunny out. You won't get too hot and when you apply wax the car's surface stays cool.
Yeah. There are several self car washes we have found and use that are fairly close and in really good shape. It's too bad you have to drive that far to use one that good.
Thank you for the comment and for the suggestion. It should work too. For us, the floor was pretty clean and the spray was strong enough to push the dirt out. If you don't mind, please share our video with anyone else it will help.
Avoid hitting the paint at a 90 degree angle with the power washer as often displayed in this video since it drives dirt into the paint, shallow angles are better.
Like he said, not if it’s a newer car wash with newer equipment that has animal hair brushes. And if you use the power washer to rinse the brush first, and get the brush saturated with foam first.
I definitely should have watched this before washing my car this morning and not after. I didn't rinse the foam brush, so it left streaks on my car twice, so I just did the automatic afterwards. 😂 But I'm going to try this again next week. 👍
Thanks for watching and commenting on our video. Make sure to also wash a panel at a time and wash in consistent and overlapping motions. I find that sometimes if I don't properly overlap then I sometimes end up with streaks in sections that I missed... and I don't find out until the car dries. Please like and subscribe if our video helped you out. Enjoy your clean car!
I prefer to use the foam brush just to spread it all over the car, with very smooth and almost no pressure. I use my own clean fiber cloth to wash it . Thanks for the video!
That's always a possibility. The main concern is that you are using the facilities without paying for it. Usually, most places are ok with this as long as it isn't busy. But when it gets busy they will kick you out if you aren't actively paying.
Thank you! I moved to a townhouse so I can't wash my car from home anymore and I really want to take care of my new car. I kept leaving the self car wash with white water marks and I was so frustrated. Thank you for the video !!!!
I just wanted to do a run on this topic to see if any buddy actually uses the wax from the pressure wand at the wash. Or which of the options are really just a way to make more $. I have a better grasp of what I'm doing wrong. So, who are you and why do you know so much about c l cat wash protocol. Lol. Thx
