Howto design a Hirth joint

Подписаться 3,4 тыс.

Просмотров 4,4 тыс.

50% 1

I show how I modelled a Hirth Joint in FreeCAD. A Hirth Joint is used to connect two shaft's together using tapered teeth that mesh together.
Support this channel
I am very grateful that you watch my videos. I am constantly trying to improve the quality of the videos on this channel. If you'd like to help me do this, please consider supporting this channel to allow me to continue to produce content for your enjoyment.
👉 Help support this channel by buying me a coffee: www.buymeacoffee.com/gds
All donations are greatly appreciated and will be used to purchase equipment to improve my productivity and increase the quality of the content that I produce.
Contents
🔹 00:00 Introduction
🔹 00:41 Example Hirth Joints
🔹 01:33 Explanation of the design
🔹 05:50 Modelling the shaft
🔹 07:53 Modelling one tooth
🔹 19:44 Adding remaining teeth
Workbenches used:
🔹 Sketcher
🔹 Part Design
🔹 Spreadsheet
FreeCAD links
👉 FreeCAD website: www.freecadweb.org
👉 Downloads: freecadweb.org/downloads.php
Copyright Glasson Design Studio 2020. All rights reserved.
Where to find us
👉 Website: www.glassondesignstudio.com.au
👉 Facebook: / glassondesignstudio
👉 Instagram: / glassondesignstudio
Credits
Writer, Editor, Producer: Geoff Glasson
Music
Title: Existential Belief
Publisher: S.I. Publishing (SOCAN)
Available through AUDIOHERO

Хобби

Опубликовано:

4 авг 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 14

@GlassonDesignStudio 3 года назад

This video was requested by Kurt M

@kurtmeinders413 3 года назад

Thanks for doing this.

@GlassonDesignStudio 3 года назад

You’re welcome

@kurtmeinders413 3 года назад

Thanks for putting this together. I really like the use of the spreadsheet. I use the information for both 3d printing and wood working.

@lizardking427 3 года назад

Hirth teeth angle is 60°, mainly for two shaft coupling, your two axes can not be coupled

@GlassonDesignStudio 3 года назад

Thanks for letting me know

@lewiscobb7817 3 года назад

I'm just learning Freecad so bear with me 😊 The only thing that confused me in your video was when you were relocating the tooth profile sketch from the xz plane out to the tooth location near the perimeter of the cylinder. You were in the placement section of the combo view but were adjusting a z axis offset, yet the sketch was moving along the y axis based on the xyz indicator in the bottom right of the screen. It was obviously the right way to adjust it but why did it take the z offset and not the y offset ? Hope I explained it right. Great videos and many thanks for your efforts. Cheers from Eastern Canada 😊

@GlassonDesignStudio 3 года назад

Hi Lewis, Thanks for your feedback. I haven't forgotten your question but I've been very busy and haven't been able to put something coherent together yet. I'll get back to you as soon as I can.

@yannickjacob1648 3 года назад

Z-axis for the local coordinate system, not the global one.

@lewiscobb7817 3 года назад

@@yannickjacob1648 Thanks !

@LuckyCatAlex 2 года назад

Thanks for this movie I'm sorry but I can't understand how are calculated Computed values sc_InnerRadius and sc_ToothOuterEdge are the simplest formulas from them for sc_OuterToothWidth I thought I can use calculation of base of triangle by angle and one side(I use s_CylinderRadius for it) But for s_CylinderRadius=15 and s_NumTeeth=14 I got 3.36 but in movie it's 5.73 Could you help me with Computed values formulas? Thanks

@GlassonDesignStudio 2 года назад

Sorry for the delay getting back to you. I'll help where I can, but please remember that I'm not an engineer and the formula I used in my video were created specifically for that video. I not the slightest bit surprised to hear that you are getting different results since it sounds like you are using different formulas to me. That said, how can I hellp you?