Husqvarna YTH2148 Drive Belt Change

Подписаться 47 тыс.

Просмотров 217 тыс.

50% 1

Vid on how to do this with some bsing thrown in.
Disclaimer:
Due to factors beyond the control of Hank's Garage, I cannot guarantee against improper use or unauthorized modifications of this information. Hank's Garage assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. Hank's Garage recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of Hank's Garage, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Hank's Garage.

Опубликовано:

11 сен 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 34

@hanksgarage_ 6 лет назад

Gas tank was removed as it was being replaced, you dont need to do it for a belt change.

@jasonwatson8375 2 года назад

What did you use for a fuel tank

@alexe.2291 5 лет назад

Nice video; it helped, thanks... Couple pointers for anyone else doing a similar job (mine is a Husqvarna YTH1342): 1) it looks like you are missing a "belt keeper" that bolts on under (against unibody) the idler pulley. Part #532 17 55-56 on my schematic. 2) pause the video at 5m25s to see the proper routing. V is around the transmission pulley, straight run through the belt keeper to the engine pulley (still V side), then directly around the clutch pulley (still v side), then directly to the idler pulley (flat side of belt), and back to the transmission pulley 3) like you I removed the PTO clutch, but now that I've played around I believe the belt should be removable by simply keeping the clutch pedal depressed - hopefully somebody can confirm Thanks again! -ace

@scottward4316 3 года назад

Thank you very much for putting this video up. Big help. I have the same mower. BTW, should the tensioning wheel spin? Mine is stuck like glue.

@mikedunning424 3 года назад

Yes

@Blayze1017 Год назад

Nice snake skin at 2:25

@cameronrichard8098 2 года назад

Hi Hank, is the engine pulley that's attached to the PTO clutch suppose to spin freely like the other pulleys or no?

@tylerhaney09 5 лет назад

sounds like it needs the valves adjusted, that's why it hesitates before cranking

@hanksgarage_ 5 лет назад

Already been done in another video made after this one

@patrickcuyno2586 4 года назад

I have a Husqvarna YTH2448 Riding Mower that I would like to flip on its side in order to replace the steering bar because it is nearly impossible to remove the bolt & nut at the end closest to the steering column. Do I need to remove the gas and oil before setting it on its side? Will turning it onto its side hurt the inside of the engine in any way perhaps from oil getting into areas where they shouldn't? I'll remove the deck before flipping it.

@tristanheckler2568 7 лет назад

Great vid man!

@hanksgarage_ 6 лет назад

Tristan Heckler thanks bud

@mowerrepairshopfortscottkansas 6 лет назад

Good Video buddy

@amberfhscott3885 6 лет назад

KB'S Small engine Repair parts & Service 8

@jamesaydelott6042 7 лет назад

nice work hank! I buy riding mower that need work and fix them up! Butt it like you said lawnmowers! You never know what your getting into sometimes!

@hanksgarage_ 7 лет назад

James Aydelott hey man yea lawn tractors can very quickly not be worth fixing. Thankfully this one was and its owner loves using it !

@thomasthibodeaux7548 7 лет назад

Be careful with that carb when you take it apart if it’s a Nikki, there is a very small brass jet that fell out on the first one I ever rebuilt. I didn’t realize it fell out and the engine ran fine until I engaged the blade. Had to go on RU-vid to find out what was missing, found the jet on the shop floor and she ran perfect after. This might be a good topic for a future video.

@shazamitt1721 Год назад

thanks dude

@Ytu477 5 лет назад

Would you have an Idea what's going on with mine the clutch doesn't move as well as forward and backwards doesn't work its a Husqvarna YTH23V48

@barbeychris2636 Год назад

good product fast shipping

@DaCoder 7 лет назад

Video seems much better 👍

@hanksgarage_ 6 лет назад

da coder really? I didn’t make any changes

@scraig000001 3 года назад

Great video man I did the same thing . flipped mine over and and changed out the drive belt ..the problem Is I need to change out one of the plastic pulleys and I cannot get it' off The bolt just spins ..suggestions would be helpful thanks again man. I have a 2004 huskavana YTH1542 It's the idle tension pulley

@hanksgarage_ 3 года назад

Try and get something on the other end to hold the bolt in place, or try and use an impact and you may get lucky

@scraig000001 3 года назад

@@hanksgarage_ thanks man.. got it.👍👍

@greggerdner2443 6 лет назад

What do you think of Predator engines from Harbor Freight ? Good/Bad ?

@hanksgarage_ 6 лет назад

Gregg Erdner imo they are far better than the new Briggs are

@tommyhanlon8012 7 лет назад

Ok Mr.Hank, ...... what's with the ''Ming The Merciless'' Beard look ? ..... Has Briggs not made a mini mower to trim that off ? :~)

@hanksgarage_ 7 лет назад

tommy hanlon haha I’ve had that forever man !

@dannylewis4225 2 года назад

I put my drive belt on without taking the pto off I did first time but 2nd time nope I started at back of it put the belt through like it shoudl be and got to front and pry it a little bit with wrench and it went on no prob