I Built an Engine With Double Pistons for Maximum SPEED! 

What other things should we build in Scrap Mechanic?

Just so you know kAN, the average in the dyno is a moving average. It only uses the values from the previous 5 seconds of it recording, so by pressing the reset button, you are completely wiping the table of values. If you let the engine run at the new rpm, it will update to be accurate in 5 seconds, but by pressing the white button, it takes 5 seconds plus the time it took to press the button.

brother I'm a 34 year old construction Forman, I came across your channel cause I watch some gaming from time to time. I'm glad I did. its extremely interesting watching you build these engines. you are extremely smart. you build this stuff with ease. I realize you have been doing this for years but its pretty amazing to me. I am glad I found your videos, I'm learning a lot. I'd really like to see piston engine with any kind of trans and diff. I know how hard that probably is, but I will watch even if you fail. I cant tell you how happy I am to have come across your channel these physics fascinate me. p.s. sorry if this is difficult to read. I am terrible at typing, I have carpel tunnel.. the more I type the more it hurts the more I don't care about correct grammar and punctuation.

Instead of stall point to stop the engine, what I usually do is to rotate the sensor themselves so none of them see a the "encoding wheel". This way I make sure its "off" without AND gates that add delays.

I have been really enjoying your piston engine journey! Please keep making content like this. I get so hyped every time you post one of these videos.

by having pistons stacked, when the first one push, the second one get longer before retracting because of the speed, which loose you tons of performance (the "opposite" will happen if the piston were in the same direction)

You realize that you can just have to controller loop -15 rather than +15 instead physically changing the gear in the back

I thought about making an engine like this before, but I didn't get around to testing it yet. Its a cool concept which I think can be pushed further to 600RPM no problem due to the conrods and overuse of pipes. Overall this is a great lead-in for building a Kein-engine, so I better see one in the next video. Actually, I much prefer to see best builds next video, then a Kein-engine afterwards.

This is definitely some cool stuff! Can't wait to see more!

So, you built that little piston stack and showed how it jitters a lot. Does that happen when attached on both sides? Like, could you utilize that silly interaction as the movement? Because that seemed to move a lot faster than normal piston movement ....

Love these videos some much man 👍🏽

This is so cool!!!

Try a quad piston set up as opposed to a dual piston setup. That way you can push down evenly.

instead of putting them against eqhother, you sould have put them on the opposit sides top and bottom of te arm that you made longer to prevent collision with the shaft. So it works like a steam engine piston.

When is the survival run with all this new found piston engine knowledge come out?

On the chasi you should try to use pistons to switch the rear gear, instead of just breaking it and replacing it.

Thank you for listening to my idea. Good engine design too by the way! Love your vids buddy

I love how there's a new upload everytime i go to the youtube homepage

0:10 that piston setups reminds me on some certain piston setups in minecraft involving sheep... *cough cough*

Hay Kan I think if you had two crank shafts you could simplify this design just put a bearing in between the two pipes connecting to the pistons delete the extended pipe pieces towards the middle so one pipe can connect to A crankshaft forming an L pattern with the Pistons and the part connecting the two pistons will spin around the engine. putting the two crankshaft closer to gather, would Decrease leverage and increase speed

Love these

Could you use the funky pulsing from the pistons set to 1 in series like that, as just, some kind of really fast system? Tho, I imagine the torque is bad, but that's what tremmel gears are for, yeah?

man I just can't wait for this update to scrap mechanic for survival but then the only issue is I'll have to re-download it :P the survival part is fun as hell would also like to know if we are keeping the old save worlds or having to start anew, fresh start wouldn't be bad just finding a nice spot is prob the hard part :P but do need to be able to learn all blocks iin the survival even the big industrial parts

honestly, with this piston setup you could easily add more pistons without adding any bearings, would be interested to see how differently it preforms

KAN: Who's a good little engine!? Engine: spazzing prefusely

Love the video! But you should use this to make a boxer, might be more evenly balanced 🤔

Hey Kan, I heard from Hyce that you calculated the terminal velocity of a Shay, and I was just wondering which Shay you used in your calculations, and what said velocity was.

I had been pondering on the idea of using 4 in a grouping

I would put the diff gears on the body on pistons, so you could flip a switch and choose CW CCW on a whim. Not sure how close to IRL SM timing would be for engies, but would you want a IRL ignition timing map for a real running engine, maybe to try adaptive timing on these pistons engines?

Con rod - that's funny :)

The engine torque seems much more realistic and reasonable when you consider that your driving your engine with hydrolics rather than making an explosion machine.

I feel the more and more RPM you push out of your engines, the more you'll need good transmissions to use the power.

Good thinking with stacked pistons. How about stacking even more?

nice vid

Is there any way to use the pulsing effect of the three length-one pistons to get extra super fast rotation speed?

Hey @kangaming wouldn't U think reducing the vibrations from the chassis would help increasing the torque delivery Like making the engine mount higher and keep it at 0%. Because angle of the engine might also affect the angle of the timing wheel or however the combined angles are calculated should mabye make a video on the most efficient way to mount the engines

that engine is crazy.

Could you use the piston twitching to power an engine? Not sure what you could do to get the timings right though.

Damn Kan really thought he ain’t good enough at piston engines and decided to learn everything

What about at a 90Deg angle? to pull and push diagonally. should be far more compact?

This is the jankiest engine I've ever seen It's beautiful

If you want speed, why not try a simple lever? Instead of connecting the crank directly to the pistons, connect it to an arm with a pivot off to the side, with the piston attached near the pivot. If you want torque have the pivot on the crankshaft side.

use a heavy flywheel it will help the piston engine push past the stall points.

Imagine if that piston engine had a twin on the other side to neutralize the forces of momentum out side of it and then the wheel that's spinning from there was treated like flywheels that fed into the main transition point that actually gave power to the vehicle and because of them being two of them you can make sure there on the opposite piston position that's most optional there for just making even more nuts in power

I wanna build that engine, and add a second line of pistons in this configuration at the bottom and see what that would do

try to make a light car with 2 engines but 1 of them is like mirrored to make the torque glitches cancel out (maybe). And it should have double the power i guess

hey kan, what are your thoughts on scrap mechanic and chapter 2?

If you want to make something that looks even more cursed, put a piston in the connection rods, then set all pistons to distance 1.

Try pistons ontop of pistons, in one big long piston

Now I want to rebuild some of my old engines with the survival mode pistons since they have more power

I'd love to see how that engine fairs on a chassis with wayyyyy less mass

You should try and make a steam train with pistons on the wheel that go up and down to make it move.

What would happen if you combined two engine types together? For example if you did 2 single pistons and 2 double pistons one one shaft.

If you build stops above and below the pistons you might be able to get more torque sice the pistons would be forced to push the crank shaft

If u stretch the pistons and give them 0 power from smart controller, u could go into the 1000+ rpm

Just how much power do the jittery pistons have? Is that something you'd be able to utilize to try to make an even faster engine?

i don't know who told you a piston pass through is bad, its not the 2x1 ramp actually has slight collisions. If you have blocks or whatever collide to the side of them, it can help with containing the cranks position but honestly it's not ''better''.

Hoorah

Hook it up to some propellers in opposite directions and make a plane

This is pretty much like a Duel Overhead Cam Engine (DOC) engine. Lol

... Wouldn't stacking two pistons give an increase in speed while avoiding the 1-tick delay in the logic gate? If it meams that the crank distance increases, you could get higher torque but still rin at 300rpm.

It has the same hp and shape as my e30s m20b25 😮

LOL i want you to fix that steering

Make a high revving v10 (like int the mclaren solus gt)

That looks like a vr6 engine but with 2 extra cylinders

And what about using the multiple piston jiggle as power?

Kan try using a version of the extreme mod for some super fast and super strong pistons would be cool to see a 1000 rpm piston engine.

bro i was just messing around withj this idea myself lol

How many pistons can you stack like this until it breaks? 5 pistons per piston??

Here's to hoping he uses a T piece between the two pistons

now all you need to do is make a 4 sided double engine

still no flywheel.. 😁

I can't see how a forward and backward piston would be functionally different to 2 forward pistons.

I have a challenge for you. It’s in the work shop called “Kan fix this challenge”

you should really get a mod or make something that shows the exact numerical angle instead of having to kind of guess the precise angle

20:09 this is not close to that look at all if you seen the engenes that have 1k+ rpm

Short stroke (short lever) when

Wait, so you can hook a chair into a controller??? I didn't know that.

Kan make a 24 cylinder engine

one of the pistons on there does nothing as extending one will push it up which you cant do unless the other one is down which is useless as you cant push the other one up

Why not place that engine 90 degrees so you can remove that wierd pipe transfer to back wheels? ... also 2 engines = more power?

alternate title: kAN builds a 1.9 tdi

bread

your engine has 10 more HP than my car lol

What if you secure the engine to the actual car to make it stop going at an angle

Make a V8 with this piston set up

one thing i never understood in your videos... why are you painting the bearings if this is just for testing? like i get that it just takes a second, but why? xD especially with the ones that are completely covered by blocks....

wow im early

w-16 when?

you should hook up a normal gas engine to the dyno and compare i ot yor engiens!

Pistons in retraction have very little strength

Piston engine CLIMBERS?

i just manage to get it to go 723 rpm !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!🤯

The reason I hate this game is because even if you create something functional, you can never use it for any purpose, I mean in survival mode.

Bro i cant anymore, start putting flywheels on engines.........

why not put the pistons in line with each other? They'd still stack and wouldn't have no torque

1! Exept kAN

Now add stuff thats useless unless with context that only 1 manyfacterer really makes/uses that style dueto making their parts peprietary

it looks goofy but it's faster

V8 pistion plane