I designed STM32 MCU card for Speeduino! 

I agree 100% with you! I admire him. Good job man!👌🏻

Thanks!

Well yeah I only speak Finnish and English..

Thanks.

Yeah bit strange that they didn't give any sponsored link or so. But at least they gave me free hands to do anything with the video, so that's nice 😁

Thanks!

It should work just fine on any speeduino v0.4 based board.

Hi! Thanks. No I don't have any specific tips for those.

The jumpers between wasted spark/sequential and for injection too were on the rev2.0 because of the speeduino FW limitations at the time. With current FW versions, you can leave those open and assemble the board with 6-cyl sequential fuel and spark. Then run the custom 6-cyl sequential injection FW in the Mega and use wasted COP mode for coils and it will work. And if you later upgrade to this processor, you can just switch to sequential ignition in TS.

@@pazi88 great, thanks for the tip

The number of IO has never really been a problem. Even the Arduino Mega has way more IO than you need. The Speeduino boards just don't utilize those well (and earlier there really weren't features that would have benefitted from that). So not even half of the IO is actually being used. I have designed my newer boards to have more IO than other Speeduino boards have to be able to use the new features easily. Problem in Arduino Mega has been lack of timers to do more than 4-cyl full sequential, but this board solves that problem. And also the Mega doesn't have enough external interrupt enabled pins to be able to use all features that require those. Like VSS, dual CL VVT, flexfuel etc. But this board solves that too.

@@pazi88 Parabens e Sucesso Sempre!!!

Unfortunately no. It doesn't use the standard Arduino Mega board, but the Core4. So this doesn't fit that.

That's alternartive for the sd-card slot. It's basically sd-card in a chip. But if you have sd-card slot there, you can't even install it.

​@@pazi88Suspected as much but had to ask. Thank you for your prompt reply. Looking forward to trying things out. I övrigt anser jag att Danmark gör bättre lakrits än Finland. Salta pingviner ❤

Well, yeah, if you have already speeduino running on one that uses ie. v0.4 pinout.

Yeah it will be in the next video (finally) 😄

Hi! Unfortunately these aren't for sale anywhere currently. You need to get these made by yourself.

Not really. 8HP is really complicated beast and good tcu controller for it is hard to acheive. I know there are few tcu's for it that replaces the stock one, but those aren't really good for street car 😅 But anyways I plan to step up to the 8HP game with in my mind better option.

@@pazi88 yes indeed there are not many ecu for the gearbox the only one that I know is turbolamik I also currently mount an 8hp but I am missing the calculator.

@@M328turbo Check out this one: 😉 www.canformance.net/product/cantcu-transmission-controller/

@@pazi88 Oh thank you very much for the information. I order immediately 🙏😎

??

@@pazi88 on GitHub I mean, but I already found it. thanks for your work! 💪

From my GitHub: github.com/pazi88/Speeduino-M5x-PCBs/blob/master/m52%20PnP/M52%20temp%20sensor%20calibrations.xlsx

Yeah same tune should work just fine.

Can you be more specific that what components are discontinued?

Kiitoksia! 1. Oman kokemuksen mukaan tommonen THT USB-B liitin on kaikkein jämäkin fyysiseltä rakenteeltaan, mikä on iso plussa autokäytössä. Niin siksi valitsin sen. Toki ko. projekti on saatavilla EasyEda:ssa että jos haluaa, siihen voi vaihtaa USB-C liittimen 2. En oo ikinää oikeen lämmenny Linuxille, vaikka sitä oon koittanu opetella. Onnistuu kaikki hommat niin paljon nopeammin winukalla. 3. En oo vielää, mut pitäs kennottaa 😅 Monia akkuja on kyl tullu kasattua ja korjattua, mut noita thinkpadin akkuja en oo väsänny.

@@pazi88 Kiitos vastauksesta. Oman T430:n akkukesto tuplaantui uuteen tarvikeakkuun verrattuna, kun nakkasin Panasonicin kennot sisään. Pitää vaan muistaa herättää jumpperilla se turvapiiri 0V:n jälkeen ennen kuorien kiinnitystä.

@@vicmac3513 Joo tuossa on aika kuollu akku jo, vaikka onkin isoin tehoakku mitä noihin on saanu. Varmasti riittäs akku melko pitkään jos tuon kennottaa uusiksi moderneilla kennoilla.

In speeduino the Arduino Mega only has 9-timer channels left for inj/ign outputs. So it can run up to 4-cyl as fully sequential. But with this, there is plenty of timer channels to run 8-cyl as fully sequential. Or even 12-cyl with some code changes.

@@pazi88 thx for the explanation! :) also, with this one it wouldn't be necessary to buy the Arduino one right? I could straight up buy this one

Thanks. The 202310 is full of comms bugs, so I wont be making it available for these. I'll wait for next one. There isn't really any new features on that, so it doesn't matter.

You need cam signal.

@@pazi88 after restarting the board the hardware test output is working. I can turn the ignition leds individually

@@b3dr01994 Ok. It should prompt to reboot the ecu after changing things like that. It needs to reset properly to apply those kind of changes.

As I said in a video, you need to order those by yourself.

Tietotekniikan insinöörin oon AMK:sta, ja tällä hetkellä oon Keysightilla töissä. Voit googlata firman, jos ei oo tuttu 😁

Most of my designs are with through hole parts, so I don't think it's feasible to get those assembled. But the rev 3.0 M52 board is SMD and so is the m52tu/m54 one. And for those the pick and place files should be in GitHub.

thank you@@pazi88

@@pazi88 any plans to update the m50 board to 3.0?

@@tre_2EC0 Yes it's in the plans, but I don't know when I have time to do that 😅

Yes it is.

@@pazi88 would you be that kind and make a video about it? Btw best youtube channel!!

Roughly 50€ per board with current prices.

Tuskin ihan hetkeen on tulossa. Ainakin mitä oon DIY yhteisössä tekemisissä, niin ei oikeen hirveästi ole suorasuihkutukseen kiinnostusta. Lähinnä kun niissä kummiskin melko äkkiä tulee rajat vastaan lisätehoa hakiessa (mikä on se juttu miksi siirrytään pois orggis ecusta). Niin sillon on vaan helpompi siirtyä perinteisiin suuttimiin.

@@pazi88 karstahan on kaiketi suorasuihkun ongelma ollut ja siihen on reagoitu laittamalla toiset suuttimet perinteiseen tyyliin. Eli isot perinteiset rinnalle niin tehojakin tulisi ja muutoin käyttöauton normiajelut menisi sitten niin että lisäsuuttimet olisivat suurimman osan ajasta kiinni tai lähes kiinni. Se Linkin ecu ei nyt enään maksa kuin 3keur mutta sekin on liikaa kun koko koneen saa monesti jo siihen rahaan. Toivottavasti sen Linkin joku hakkeroi😃 ja muuttaa esim. Speeduinoon.

I would guess that no. There is a high chance that this has different pins in use than that.

Oli tarkotus, vaan vaimo oli pätkiny sillä VOM koiranruokia ja haisi niin pahalle se ettei kehdannu käyttää 😅

Joo, kunhan RU-vid enabloi mulle ääniraidat eri kielille. Toki tuleva bimmerparty video on suomeksi, kun se ois vähän hassu puoleksi englanniksi 😅

@@pazi88 tätä odotellessa 😁