*I turn microwave transformer into a welding machine new technology* ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-U-ub_hPVo1k.htmlsi=n9_ncSCngAyl2QEB
Yea I'd like some proof that the belt used here is actually capable of transmitting 650w or so like your demonstration. I find it hard to believe. Also the core isn't even closed and there's a huge gap between the magnets and the pole piece. It just seems so far fetched.
@@bobbybiggs4348 Yup, lucky if that arrangement manages to generate more than a couple of watts. Notice how the ground looks like it has been dug up all around the area where he's "testing" the generator? I'll bet anything there's an extension cord buried in the ground to hide it from the camera. The demonstrations in the video are about as fake as fake gets. Even the first test with the incandescent bulbs... you would never get incandescent bulbs to glow even a little bit by hand-spinning the generator shaft like that with little effort!
@@TehMG "Even the first test with the incandescent bulbs... you would never get incandescent bulbs to glow even a little bit by hand-spinning the generator shaft like that with little effort! " Как раз в данном случае можно заставить, надо соединить последовательно обе обмотки тогда напряжение увеличится в двое, а лампочки загораются при напряжении где-то 50-60в, и ток им нужен небольшой.-Just in this case, you can force it, you need to connect both windings in series, then the voltage will double, and the bulbs light up at a voltage of somewhere around 50-60V, and they need a small current.
Ok I find this all questionable so hear what... I'm looking to create some free current and I happen to be collecting microwave transformers. So I'll test this theory myself... if it doesn't work following all the methods displayed then I'll call out this video. And if it does then I'll upload it...
I recommend 500 turns on each side of Transformer with thicker magnet wire to give you more amps. Fill both sides of transformer fully with wire. Use n52 neodymium magnets and shave the epoxy down more to a 1/16 of an inch. Use 4 of these microwave transformers. You can also go to a car parts store and purchase a mechman alternator then hook up a solar panel to power the alternator , then spin the shaft with a motor and you get a nice source of power.
Nice work! But the steel plates used after the aluminium fail for holding the rotor can act as a magnetic short circuit that heats up the metal and lets you loose some of the energy. I also would try to use 3 or 6 coils to get 3 phase AC.
Mr. Michael may you explain me some? Small Generator is no taking fuel which is this coil? If smaller generator taking same fuel like these small using things than what the benefit? Please must reply.
Молодец, чувак понимает как можно управлять симисторами с помощью магнита и катушек. Кто физику в школе не учил, для того весь мир полон чудес и волшебства. Расходимся, нас нае..ли.
@@alexinfinity2870 мало взял! 17 кВт! Он ещё сварочный полуавтомат просто забыл подключить, чтоб тот вентилятор сверху приворить, на активное охлаждения гены😂
Ficou bom . Porem , vc poderia ter pego um atalho ! Ao invés de desmontar a bobina de três volts e ter removido o secundário do transformador , poderia ligar o primário em série c secundario de 3 e de 10kv transformando tudo numa só bobina . Além de economizar tempo , vc teria mais saídas de tenção e maior potencial de geração. Outra ! A onda de saída deve ser bem quadrada no vale e bem pontiaguda nos picos pela frequência das lâmpadas. Tipo um riple forte de saída . Vc poderia ter colocado mais imãs em números ímpares, para imitar a frequência da rede doméstica e diminuir o intervalo de ondas formando uma senoide. Isso diminuiria a necessidade de maiores rotações e ruídos assim como desgaste . Não precisava ter desmontado um motor bonito daquele . Pelo jeito é novo . Qualquer induzido velho já seria suficiente , de ventilador ou de micromotores de refrigeração que acha muito em casas de recondicionamento ou no ferro velho . Ou então uma sucessão de arruelas grossas num eixo tu já faria um rotor produtor de senoides se vc colar imãs em múltiplos exatos de três. Gostaria de ver um vídeo de vc transformando um trafo desses num motor. Faça um buraco no nucleo entre as bobinas que vc tera um motor e transformador. Abraços!
*What would really be better is to attach a 3 to 1 ratio Waterwheel to your homemade power generator 👍instead of depending on a gasoline run drive source. Also, how about a rectified circuit to help stabilize the current at 115 Volts AC @ 20 Amps Max ? This would help compensate for any variations in revolutions of your rotor to a certain extent and smooth out your AC cycles to 50 or 60 Hz.*
Mis felicitaciones tu proyecto energía libre con imanes neodino Muy bueno buenísimo excelente Lo que te falta es elevador de tensión eléctrica y estabilizador de corriente . dos transformador de potencia
А каша то уже варёная была, он просто её подогревал. Я так понимаю... Или вообще не включил, иначе обороты мотора должны были поменяться от нагрузки, по-любому, хитрит однако. Небось со страны AliExpress 😉
Now some of the magnetic flux is leaking in the air gaps between central core and sides instead passing the copper coil. The bearing housings also need to be made from non-magnetic material, because they now are shorting some of the field to pass trough them instead of the main lamination. I have learned motors and generators design in university and I know how important is the size and position of each element and how the magnetic flux is running trough iron cores and air gaps.
This may be off topic, but someone might find it interesting.Over unity electric generator. By AMA. Segment 1: 1 motor with bar connected to it standing vertically. Circular disc connected to bar that has magnets embedded in it surrounded in high permeability material to focus magnets outward pushing force in an upwards direction from top of disc. Segment 2: Hollowed out cylindrical Bar of material horizontally positioned. Flat hollowed out ring shaped material with openings around its outer top flat edge. Magnets surrounded in high permeability material embedded in these openings. Magnets positioned in openings around ring are in at least 1 of 2 configurations either all N magnetic field pushing out or N,S,N,S all around it. Just depends on whether your going for Piston structure or spinning structure explained below & whether you want it to be DC or AC current. Place these all along the cylindrical bar connected to it solidly, except at far ends of bar. At both ends of bar place ring of material that can be magnetically repelled in specific locations. (magnetically repelled in specific location is in reference to outside of ring area that faces away from center of bar)(Other side of same ring facing in towards center of bar is capable of being magnetically repelled all around) Ring must be connected solidly to bar. points of repulsion on these rings is off set from each other on each end of bar. 3 Hollow ring structures with small square bars protruding from each. Ring structure has all magnetic repulsion on inside of ring shape & can rap around the main bar so that the bar wont be causing friction on things as it moves back and forth or spins. 1st positioned around far left of bar, 2nd position at center of bar (be sure to leave enough room for magnetic structures to be able to move back and forth without hitting it) & 3rd positioned on far right of bar. Tube structure is constructed in two parts that fit together on top of each other length wise over main structure. Tube structure has 3 square openings for the bars that the Ring structures that are connected around the main bar keeping it from causing friction on structure, to slide into. This tube structure is designed with material that does not block magnetic fields. Perhaps some type of transparent material glass or other. At both ends of the tube structure there is a built in circular groove that will house a round disc. The ceiling/floor/left side/& right side of groove has openings for small magnets to be embedded in it, so that the pushing force from magnets is pushing in towards the edge of disc that goes in this spot. There is also 4 openings located on the top, bottom, left & right positions of the open groove. Small magnets are placed in these spots so when round disc is in position these magnetic fields will hit sideways keeping it from generating friction against structure. Far Ends of bar has Cap structure that screws over tube halves holding them together. Cap structure also has 4 points on inside top, bottom, left & right that have openings. These openings have small embedded magnets in them that exert there pushing force outwards (sideways) so it will keep disc in position, generating no friction against structure. Cap is made of material like tube so it does not block magnetic fields. (Note: These magnets in groove and cap structure are only needed for piston design. If Disc is directly connected to main bar so as it spins the bar spins, magnets are not needed here). The disc has ring around it (ring of material goes around outer edge and folds over front side & backside a small distance) that is repelled by magnetic fields so the 12 small magnets will keep it lined up but it will be able to spin without causing friction on structure. The disc has openings on it's flat side that face inside of tube and magnets surrounded in high permeability material are embedded in this disc. The disc has small bar that is connected to it's center that goes all the way to the other end of bar structure through the center of the hollowed out bar and connects to disc on other end. Disc on other end is set up the same but magnets embedded in it are off set in comparison. As first disc spins the magnetic fields will push against specific spot on disc connected directly to bar, pushing bar in other direction, once bar is fully pushed over, further spinning of disc will then align the other sides magnet to push it back. Tube structure also has half moon shaped protrusion on inside and on both halves so when tube is connected they line up to make a full ring shape on inside of tube, these half moon shaped protrusions have at least 1 small round opening on it's side in middle of curve that faces away from center of bar. The opening has a small magnet embedded in it so magnetic force is repelling out sideways away from center of bar. The protruding ring is positioned to line up slightly further in towards center of bar then the ring of magnetically repelled material connected directly to bar. This way when bar moves right or left it is magnetically stopped after a short distance. Copper coil setup: Copper coils are wound in at least 1 of 2 ways. Either coiled in circles next to each other (Like if you wound coils around a cylindrical bar) or laid out in a row as if wire was on flat table going up then bent to go down & back up until it formed a flat rectangle of wire bending up and down and then the entire structure folded around tube. Copper windings are then lined up perpendicular to magnetic fields on outside of tube. Ends of copper coils are connected into separate construct that will allow electrical current to flow somewhere else. Circular construct is built like a stand that goes around the outside of motor segment. Circular construct has flat ring of high permeability (magnetic field shielding) material that has small openings that will allow magnetic fields through specific locations. Top of circular construct has groove to allow the horizontal bar to balance on. Circular construct can also be placed on other end of bar so it is balanced. The motor segment is positioned so the disc connected to the bar that is connected to the motor is lined up so the disc passes under the horizontal bars disc that is at end of horizontal bar. The high permeability material keeps the magnetic fields in disc from hitting into the disc that spins or pushes the horizontal bar until just the right moment when the impact will cause the disc in horizontal bar to spin which will perpetuate the piston motion in the horizontal bar. More horizontal bars of the same design are built and positioned around the motor segment in a circular horizontal fashion all the way around. The bar connected to the motor can be increased in length to desired height (As much as motor can handle) and more of the exact same setup is repeated higher and higher up, maximizing the over unity potential of the construct to ridiculous proportions. :D Current from the horizontal bars is diverted to power the motor as needed and all other current is diverted to power my game console or the world. :) Interesting variation to this design would be to connect the spinning discs on far ends of horizontal bar to main bar that magnets are connected to so the magnets spin instead of getting pistoned back and forth. So long as moving magnetic fields are perpendicular to copper wires it should work. By AMA
14:53 in you can see he has moved the left coil closer to the spinning magnet to increase voltage output. This is totally plausible. I agree this works
I thought it was sketchy when he was using a pair of scissors as if they were electrically isolated, but when I seen the bare foot hold down the transformer, I knew It was only going to get better 😅
@@Ghst-tl9ec Nope, you need both high voltage (above 48 V) and significant amps. One can hold on to a power source capable of delivering 10 volts at 100 amps without any problems, but I sure wouldn't want to grab a source capable of 100 volts at 10 amps. Both have the same power capacity at 1000 watts.
excelente ideia, eu acho que se adicionar duas bobinas em fase em cada lado dobra a corente e a potencia se soma ( 4 coil ) ,duas em paralelo em cada núcleo ( caberia) ,isto poderia ser movido a queda d,água ,com uma pequena represa de um rio ,,onde daria energia o dia todo ,para uma geladeira , um tv ,lâmpadas led, e radio ,
You can increase the magnetic field and the number of coils, and have the magnetic field drive the electric field, in a self contained and closed circuit.
@@bondq7424 I have a hard time believing that all these 3 items run on an unknown amount of revolutions per minute to even make a count. No way is this thing between 50-60 hz @220. Anyone care to pitch in?
@@danyf3116 In theory he has made a four pole generator so it would need 1800 rpm to spin . I don't see a problem with the engine/pulley ratio as they are equal , but I'm not really seeing his set-up doing what it's doing , no voltage regulater , etc -
It was funny when you showed how aluminum couldn't be welded with a welder like mine. If it would have welded it would have surprised the crap out of me. Loved the video
Mucho trabajo, mucho empeño. Pero me quedan mis dudas, cuántos voltios es capaz de generar? Y cuántos amperios soporta? Sería bueno realizar ésas mediciones. El calentador ése nomás ya absorbería toda la energía, y creo que ése bobinado tan chico no produciría el voltage y la frecuencia necesaria para hacer funcionar todo éso.
Estoy con vos además el tanque de nafta de la máquina no tiene nafta aparentemente, lo digo xq yo tengo una máquina de cortar pasto igual y se nota la nafta cuando está cargado el tanque esel mismo color q ese pero se logra ver Clarito el nivel de nafta y este parece vacío ... Creo q es Fake
No es fake, lo que pasa es que en esos países los electrodomésticos funcionan en 220v y no es necesario regular, esa planta es capaz de mandar hasta 2000 whatts que esas que suficientes para mover esos electrodomésticos
Great job mate! Frequency and tension are likely to get off the 50hz, since there doesn't seem to be any sort of regulation. However, all the machines you connected can work fine on a wide range. This is a good generator made from a small petrol engine and a microwave transformer. It's hard to tell how much power it can provide, but then I don't think it is a good idea to push it too far without any sort of regulation. Microwave transformers usually work at 1200w, so I wouldn't feel comfortable going over that power. Then there's frequency regulation (it defines the water pump motor 'no-load' speed) and tension regulation - too much tension and that electric cooker is likely to burn some control component. There's some information on this on the internet, let me know if you need any help to move on to working on that sort of V1.1 improvement.
The hertzer cycles will depend on the RPM which won't be much to get either from the windings on that thing he was only doing 10 RPM to make those bulbs flash about I would say 30 RPM on this thing would be making 240 volt something like that I don't know but I can tell by looking approximately
@@ronalddaub7965 Hello, it also depends on the number of poles. In this case it has 4 poles and therefore for a frequency of 60 Hz you will need 1800 rpm to obtain 220V.
Мне больше порадовало когда он в сверлильном станке обробатывал ну херли биение ноль все строго на глаз! Кстати мог бы и просто скотчем замотать магниты тоже бы работало
@@billyjones9045 кандинсатор делает ток постояным то есть когда горелы лампочки они во время врашения генератора мигали конденсатор убирает это мигание. Накапливая внутри себя ток делает ее стабилным
External power (electricity) used generate power to light the electric bulbs...if that portable drilling machine could be powered from the board socket....then it would have been super...
Тем временем Доктор Дью: - вы не поверите, но чисто случайно у меня нашлись 2 трансформатора от микроволновки и не нужный мотор). Что же, мы начинаем начинать!))))
This information is actually been abundantly available, it's just been locked and hidden behind gatekeepers at academy and three letter agencies. You can easily find demonstration of this yourself if you just look at ancient megalithic sites. Take a multimeter and put it on a rock, then hold it in your fingers, then put it on a leaf everything has a charge. It's just focusing it into a centralized point with either a capacitor or a battery Bank. Transferring it in white area is where the information gets really scarce. That harnessing it or creating it is stupidly easy take a coil and push a magnet through it where it does not touch the coils and then put the multimeter on each end it'll create a significant current.
This is a very good idea, but a better renovation could have been done. For example, by pushing the second 220 volt winding further back, a cavity would be opened in the microwave oven core suitable for the outer diameter of the rotor, because there is a very suitable space for this process in the two cores. A round hole suitable for this rotor would be opened on a milling machine so that a better magnetic coupling would be provided and this magnet rotor would be able to induce more effective induction currents in 220 windings and generate electricity. If it were integrated later, for example, even at lower revs, there would probably be relatively less fluctuation or flickering. These are my own personal opinions of course, But the 220 volt AC winding connected in series only provided an efficiency like 220 volt AC, because of the magnetic fluxes of this leakage core magnet output. If these leakages were further minimized, it is highly probable that the electricity generation efficiency would be much better, like the rotating squirrel cages of shadow-pole induction motors. Still, it's a good attempt and a good (quite successful for electricity generation purpose) renovation, well done. Good luck with.
Now this is someone who can think straight and show a good natured human thing without the clutter. Nice art and excellent power output. I can see a host of applications and other sources to spin the rotor, great up-cycle.
Ai făcut o greșeală enormă, prin care ai pierdut ceva ce te-ar fi făcut să...plutești de bucurie ! N-ai mai fi folosit motorul termic, iar generatorul ar fi mers la infinit !
Great idea anyone thinks it can't work doesn't understand basic electrical copper wire steel or iron and a rotating magnetic field same principle as in store bought or commercial generator
The best thing about it is the feeling you get when you are using this energy knowing that it is a separate Entity that you made as if it’s a Nother part of you that’s creating energy because he will get to do so awesome video man
porque por cómo fue creado, puede generar una corriente intermitente e inexacta .. tal vez alrededor de 200 voltios pico y 25 Hz .. Cualquier dispositivo funcionaría mal
Sir; by welding the laminated core as you have done, the reduction of eddy currents is bypassed and excessive heat will be the result. How hot is this project getting on the core and does it effect the efficiency very much?
It appeared to reduce the cogging when he initially spun the generator by hand? It should have more resistance to flash the bulbs. Maybe shorting it reduces cogging but heats itself up due to eddy currents?
For me it was the fact that he didn't move the generator closer to the pump. Why is everything so far apart. How is the rotor continuing to turn fast with such a loose belt. Why is the ground freshly disturbed only in that area.
Suggestions for improving efficiency of this generator. 1) add soft iron to bridge gaps between the two iron cores. 2) Decrease distance between magnets and iron cores.
@@ixflqrThe air gaps between the two laminated iron cores represent a loss; if those air gaps are filled with soft iron pieces, or better yet laminated iron pieces, the generator could produce greater current. Likewise the gap between the magnets and the iron cores is also a loss. The closer the magnets come to the iron cores the greater the current the generator can produce. Air gaps in a magnetic path of an iron core increase the reluctance of the core and limit the maximum magnetic flux in the core. The flux is proportional to current produced.
@@barneylinet6602 I've built one with a washing machine motor with less gaps and good magnets but still gave me 5v ac only and this guy lit 220v easily 🤔
Yo creo que esta muy bien demostrado que funciona. Pero hay algo que es muy importante y muy necesario tener en presente La frecuencia, si no se tiene encuenta según altitud, 50/ 60 hz, podría dañar el motor del estractor de agua y ventilador.
Скажите, я один охуел, когда он начал алюминиевый сплав к железу приваривать? Слава Богу, не получилось🤣 Хотя от приваренных подшипников тоже подгорает😁😁😁
Helloooo from the backwoods of South Carolina! Love love love this! Small enough to fit in my boat, yet powerful enough to run my lights, stove, and phone charger at our floating cabin in the swamp. Thanks for the guide, it was a pleasure to watch!
It is not usable for electronics device. As like phone charger, LED lamp. This output power is over damping. If you use more than four Yoke and rotor magnet number eight. Then it will produce efficient output power efficient frequency. This will be a smart generator.
Man I've been having issues with generators in Washington, people always spending $2000.00 on generators. I now see how they work. Thanks man, I'm now 100% sure my generators motor was too old, it backfired one day and never started again. If ida known the motor blew I'd have gotten a new one. Instead I got a different generator that's going to suffer the same fate. I need to learn how to work on motors apparently. Awesome. I do have the old one still so maybe I can learn from that one?
Bro, in my opinion, his method is not really that effective when it comes to creating energy. I've watched something that I want to share with you that you will surely like. Now, this one is legit free energy without any gas-fueled so-and-so, just pure free energy. Let me share with you the link. I think it is way way way better . ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-WwyXZfrs6EI.html
@@stasanoffstasanov9224 к бабке не ходи к его фигне на поле внешнее питание подведено при подключении нагрузки у двигателя обороты вообще не падают, ремень хлипенький сомнительно что с таким натяжением вообще что то бы работало даже если генератор был бы нормальным, ну и сам генератор с таким магнитным зазором если что и выдает то максимум светодиодами посветить
Good work! If you were to utilize smaller magnets while increasing the amount of magnets around the rotor then you wouldn't experience the rapid oscillations in the current resulting in higher Hz for a smoother output.
He doesn't know much about generators. I once recreated one of his generators and saw that it couldn't work. He made a mistake so it couldn't work. During the rehearsal, he must have taken the power off the grid and pretended his generator was working. I didn't make the mistake like he did and it worked for me. Not everything that he shows works with him. That's a little cheat.
Aproximar mais as bobinas e colocar neodimel em toda superfície do rotor deixando o com os polos aparentes não submersos na resina mas a ideia foi genial
