@@nickspencer3132 This works. The Amish use. Hydraulic Ram Pump to supply their homes with H2O. A HRP will even push water uphill ! The 1 to 7 ratio. For every one foot drop the pump will push H2O 7 feet higher. You could even use a reducer near the output end and create more pressure.
The only way to move water through a pipe is to either push water into it with a pump, use an Archimedes' screw, bubble air into the vertical pipe or make a siphon. The siphon is the only true no power way to move water. The only way a siphon can work is if the outlet is lower than the inlet. Gravity pulls the water to it's lowest point, creating a suction at the inlet. This is 100% fake. Replacing the rubber seal with a Schrader valve is the easiest way to fake this. If an air line is connected to the Schrader valve, the rising air will lift the water up the pipe and out the exit. I think there are either some clever video cuts where the air hose is hooked up and placed in the water or the check valve has been further modified to allow a hidden hookup under water with a push on fitting. There will be thousands of people who will pass the video around showing the "magic" water pump. The author will get his views and possibly $ for advertising. People don't know anymore that the seemingly impossible videos are almost always faked. Like the guys that build seemingly impossible homes in the jungle dirt - pictures surfaced of heavy construction equipment tracks when it was supposed to be done by hand. If you see it on social media - there is probably a 30% chance it's fake.
Please don't call it fake. The uploader was so close to just attach a water turbine at the outlet and generate electricity for free, copy the system a million time, energy problem solved, free energy, yes, perpetuum mobile to the MOOOOON
30% fake is like 30% pregnant (and most opinions) -- meaningless. These same guys have videos of much more powerful siphons that DO work (we use them on our farm) and I have seen no end of de-bunkers trying to discredit them. The de-bunkers are the fakes! I happen to KNOW we have been lied to by science many times over, especially about fluid dynamics. A siphon is actually a powerful vortex and it works on the SAME principle used by jet planes to fly without 80 tankers of fuel in their wings. Get out from behind that keyboard and actually do some work!!! One less keyboard warrior is not a bad thing.
@@mariana1964 yeah, heavy working on it :D Just plug some PVC pipes together and learn that it doesn't work. Did you know that a siphon is at the pipe from your toilet, why doesn't water constantly come out of your toilet if that in the video works?
You don't need the bicycle inner tube schrader valve inside the check valve. In fact, you don't need the check valve at all. Or any particular configuration of pipe. Just properly align the end of the pipe with the outlet of the hidden underwater fountain pump and presto!
The check valve allows you to prime it in those first few pumps. But I honestly don't know what the valve stem was for....the check valve was fine how it was.
In the first 20 seconds he shows you his 'siphon' begins working without priming. There is a battery operated pump. The alteration to the check-valve is totally useless also.
I’m no expert in hydrodynamics, but I do know that for a siphon to work the output end has to be lower than the surface of the water you’re trying to move, unless you’re using a pump.
bro i m also search for real project like this if this work ! if u a exprnt on this method so plz share its real or fake and also share real and sold method its bnfical for farmers !hmm i m waiting for positive ans
Okay I'll admit it, I got excited for a second. I really wanted it to make sense because I was already building my energy producing perpetual motion machine. I'm very open minded that if somebody ever figures out a way to do it, it will probably be in a way that in hindsight should have been obvious to us because it will be a very simple principle, like water crawling up a sponge.
Finally, a video to 'disprove' Bernoulli's and energy equation which I learned in Fluid Mechanics and Hydraulic Engineering. The piping must have negative head loss or the system is creating energy for this to work 😂😂
Gravity is a theory. The truth is buoyancy and density. PHD and con artists - there is no difference - They all make money spreading lies. The PHD guy just makes more money. He has to pay for his deception education, right?
Definitely works! 😁👌 I have 2 bathtubs installed 1 above the other. I use that "magic pump" to lift the water into the top tub. Then I let the water drain out of the top tub, through a mini turbine to generate electricity, then back into the bottom tub to start the whole process over again 👨🏫 I've stopped paying for electricity and even started selling the excess electricity to my neighbors 💵 My next project is creating a water powered car that uses the same principle 🚙 I should be able to finance everything with all the money I'll be making from selling electricity! And for my final project! I'm gonna turn cow manure into gold bricks! 😂🤣
@@funwithfamfun WOW! NO SHIT!? 😮 How did you manage to pull it off? Sadly, my "perpetual motion" machine wasn't perpetual motion after all 🤷♂️ The damn thing started to slow down after only 20 years! 😫 Very frustrating! Where will I ever find the time to test another?
A bomba e a bateria estão montados dentro do tubo e ele chega com a bomba ligada fazendo o barulho característico desse tipo de bomba quando está sem água. Ele bombeia com a mão até a água cobrir a bomba, que é quando a bomba começa a puxar a água e então pára de fazer barulho.
FREE ENERGY! This guy just saved the planet!! Imagine millions of these powering generators all around the world doing nothing but moving water from one pond to another, then back!
No way this is real. One of those pipe sections has to have a battery-powered pump and battery inside it. Or maybe that part of Asia is not subject to the laws of physics.
When he puts the long end of the pump in the water, you don't see it clearly, but he's agitating the pipe up and down (along the length of the pipe) which is forcing water through the check valve into the long tube and it can't drain back into the pond. When the long tube fills to the first bend (the 45 degree), an auto siphon is created which pulls the water up the long pipe and over the 45 bend and the first 90 bend. The two bends form a U-siphon which assists in pulling water from the pond. I don't understand how the water then climbs above the siphon, but the inside of the U-siphon has a partial vacuum, and the open end of the pump is at 14.7 psi (air pressure). The pressure difference (including the weight of the water) may be able to lift the water that 3 ft. I'd add a downspout there to create a second siphon. Ingenious device! U-siphons are regularly used in aquaponics to drain media beds, but the exit end is below the water level in the tank and they don't require a check valve because the bed is always filling. The height of the U siphon sets where the water will start flowing by siphon effect.
I noticed that too but it reduces the wt of the ck vlv and he also lost the seal that was removed from the disc and the schraider vlv was left in place. I suspect he did not have any silicone handy. Seems like he primes it like a shaker syphon. Still trying to understand how the flow is maintained . I may build one when I retire and get board.
Magicians use a diversion tactic that is totally irrelevant to the trick. Exactly what I was thinking when I saw the inner tube bit. Made me laugh though.
There is no way that water can go up with just having a u turn pipe.You can bring up water by siphoning provided the outlet is much lower than the source of water.Siphoning work in a way that once the water goes out on the outlet it tend to suck up the water because of gravity or the suction pressure created by continous flow to the lower section.iniatialy a water is place on the opposite side of the pipe that will act as the one suctioning the water from the source going to other side of the pipe whose end part is lower than the water source.
The machine which continues to work infinitely are called "perpetual machine" .... It is a theoretical concept ... No machine is perpetual in practice .... Fake video
the schrader valve requires 30 psi to force it open. Water has more psi the deeper it is - so the pipe goes six feet down and is 3 inches diameter - so you get greater than 30 psi to force open the shrader valve.
It's a one way valve at the end in red, which he hand forces water into a simple gravity siphon caused by the bends in the pipe ... why are people naysaying this??? It's basic flow dynamics!!
I love his disinginuity, sorry I got confounded. I love his dishonesty and ingenuity. I love when people figure out how to change the laws of physics, very impressive
This device cannot work in still water. Note at 11:25 there is a big hole on the left where water flows into the pond. Note the water turbulence too. The water could be directed towards the pipe via the red check valve.
The very steady flow of the water proves this pump is powered either by electricity, gas engine, or otherwise a windmill on a very windy day. You'll be needing a new tire tube for your bicycle. Do what I did and use a broom handle in place of the tire tube! Don't worry... the broom handle will bend into the shape of a tire tube. Kidding. Just sticking it to you like you stuck it to all of us. 🤣
Stumbled upon the thumbnail and just had to have a watch laughing thinking that either he had figured out a clever way to pump or if this means free energy. Guess it was the latter hahaaha. Sccrew you NASA - seems we only needed a valve and some pvc pipes anyway xD I call there is a pipe he pushes the inlet side into. Edit: Or watching all the way through I'm going with pump.
It takes work to elevate water from a standing pond. Without energy from some source to create the force behind that work is pardon the pun "a pipe dream".
In 6.53 to 7 minutes on the video you can hear a small pump sound inside that pvc listen carefully 😂😂😂 all of his video’s are fake don’t try to make those
owh really ? your ears is good but your eyes not.. if u rewind back and see whats near the roadside is the sound of bike not pump.. i bet your might need to go for doctor to check your ear & your eyes
@@dickymobile9189 I am not concerned by the noise, be it bike or airplane; this guy is making so many people lose their time showing a bad music hall trick .. enough for me.
I could actually see this working a little is the outlet opening craned down and wasn't aimed straight out. Seems a little too easy for the air to enter and the vacuum to break and the flow to stop. certainly not enough to squirt out of the hose like that. My vote is that there's more going on here.
Mine works so mush better if I huff the glue instead of wasting it on the fittings. Side note, abs is a lot easier on the nostrils, and it has a sweet smell. You won't need any purple primer...
the schrader valve requires 30 psi to force it open. Water has more psi the deeper it is - so the pipe goes six feet down and is 3 inches diameter - so you get greater than 30 psi to force open the shrader valve.
Well at least you're kinda right. It's electricity that you don't have not power. The ram pump uses water as it's power source, and it is very efficient. It works and works 24-7 without you there pumping it by hand.
the schrader valve requires 30 psi to force it open. Water has more psi the deeper it is - so the pipe goes six feet down and is 3 inches diameter - so you get greater than 30 psi to force open the shrader valve.
@@voidisyinyangvoidisyinyang885 The schrader valve never even opened. It was mounted in a non-watertight sliding check valve leaf and water could flow past it freely in an upward direction, straight into the little battery pump mounted inside the pipe. The valve was added for visual effect.
@@TrueSolitaire Actually the secret is when he moves the PVC pipe back and forth - that's what opens the Schrader valve. Then when the bottom of the 90 degree pipe fills up that creates a negative vacuum that pulls the water up. Then the water pressure keeps building up to push the water out the other end of the pipe.
Couldn't help but notice him building a small version of what he brought down to the stream. Not sure what the point was in doing that but it's much smaller. I'm also trying to figure out how the tire valve would be used considering it wouldn't let any water up from below without being compressed.
I actually was thinking that this was a trick using the valve stem to compress air the moment I saw the stem. Truly however this can be achieved and I use a similar method to clean my aquarium. Also if you've ever had to siphon gasoline into a container the very same physics are at play. This is not impossible. Also as he's jabbing the end into the water that's pumping water into the body up to the spout to start the flow. The only thing that's I question is the distance of the output and angle. One thing to note is if a large air bubble gets into this pipe the flow will stop. So did you build the smaller version? Results?
@@1134phi He built the small one to make it look that's how he built the big one. It's a scam to fool people who don't know simple physics, that generates revenue for the views and discussions on how it's real or fake. He knows it's fake and will keep making fake videos because there's enough idiots out there who believe it's real. His other video of an auto alternator running a motor loop, and generating excess electricity, is proof how stupid people are.
Same principle as siphoning. The red contraption below is a non-return value. Once the pipe is filled with water and flows, then it'll be free flowing.
That is not a non-return valve it is a torn apart valve stem. I guess it could help if when you put the thing in the water you slipped a hose over it and then someone turned on the water.
Note, the initial siphon pipe is equal the the other, but once it is carried to the pond it is almost five feet long. Does PVC grow in that country? Fraud. there must be a pump in the pipe. Show us the inner of pipe before placing it in the pond and then reassemble on spot, there was no glue needed.
I noticed the longer siphon pipe too. Better yet, make it with clear plastic pipe. A little more expensive, but hell, he's got 588k subscribers. He can afford it!
Right! Compare the build pipe length at 5:43 with the pond length at 0:05 - twice as long. He had to remove the modified check valve as there is now way that volume of water would flow through the tiny Schrader valve!
Total bull crap, against all laws of physics. From the time he put the pipes together before you walked into the grass we did not see him and that is when he installed a small pump battery powered inside the pipe. The check valve lets him sloshing it back and forth in the water allowed him to prime the pipe up to where the pump takes over.. not only that but when he was putting the smaller half inch or 3/4 pipe to extend it up The Big unit he was fighting pressure. The rest assured there is no magic here, only a pump installed inside the pipe well the cameras weren't on him. It amazes me how many people are falling for this 🙄 👎🏻
Nice magic trick, he should try it out on the show "Penn and Teller: Fool Us". 😉 At a depth in water of six feet the pressure is about 2.6 psi (gauge). This is nowhere near the 30 psi he says the Schrader valve needs. You could make a perpetual motion machine by using the falling water to drive a waterwheel and letting the water return to the source. A perpetual motion machine channel on RU-vid is a perpetual cash flow machine. It would be interesting to know how many there are.
I was thinking of this idea myself - I live on a lake and thought: can't I put a pvc pipe down into the water and the pressure of all that water in the lake should push the water thru the pipe, even upwards above the level of the lake. then I could have it flowing onto a water wheel to turn and create free energy. Or also do what this guy is doing and get flowing water without needing an electric water pump. Pretty smart.I do see that everyone says this is fake - okay I'll make one myself and try it out and see & get back to you with the results.
Water is pulled up by moving the pipe in and out motion using the check valve I get it. How does it continue to pull water out of the pond higher than the pond level? Gravity doesn’t allow it. Unless there is a pump of sorts.
This is one of these thousands of videos on youtube where the publishers only chase the number of views for financial gain. Although these are all hoaxes, what I cannot understand is why would you risk your good name and honour to post videos like this - and I have not specifically chosen this video to say this. It is just impossible to comment on all the BS videos out there.
the schrader valve requires 30 psi to force it open. Water has more psi the deeper it is - so the pipe goes six feet down and is 3 inches diameter - so you get greater than 30 psi to force open the shrader valve. So no - not a hoax
You can buy a gas siphon hose with a half inch copper fitting with a marble in it for siphoning gas without getting any in your mouth at any auto parts store in the US. I have 3. One in each car and one at our cabin for transferring gas from gas cans to generators with total control so I don't spill. As you jerk the hose upward from teh bottom of the gas can, a moving column of gas rises and when you jerk the hose back down, the gas continues upward for a second and then as it begins to go back downward, the marble seats in the copper fitting and stops the flow. As you jerk upwards again, like this guy does in the video, the process repeats. That part is simple and readily available in the US. It's just a simple check valve. He is using the inertia of the moving column of water to open the check valve on the drop, then it closes and holds the water in and raises it and develops inertia in motion on the rise, and then while he jerks it back down again, the water keeps rising in the pipe and teh valve opens and lets in more water, then the process repeats. What I don't have an answer for is how it keeps pumping. I suspect once he attaches the hose to the output, it acts like a simple siphon as that delivery water goes downhill out the delivery pipe. Somewhere inside that u shape there is something else happening in hydrodynamics that is causing water to pump uphill in a small amount at teh expense of water going back out the bottom of teh contraption and creating a vacuum. gonna have to look that one up.
Now, build an enclosed system, power a suitable sized motor with that water flow, and you've got yourself a perpetual power generator. And they say it can't be done 😆
but no system can be total closed you can get close, but fully, the bar for perpetual motion is way higher, just regular power generator, unfairly really regular stop and star all the, but to perpetual power generator once started much keep going on for ever to the ends of time, the second it stops it not perpetual motion
The reason why it (any type of perpetual thing)can't exist is because nothing is 100% efficient. Not the water pump, nothing. You might get away with the system for a few seconds (long enough to make a video) provided that the pump pumps up a fraction of what was used to power it. That is obviously not sustainable
Yeah, that was just what I was thinking….with a series of basins on a hillside connected by these, and then to a gravity fed water power generator….seems like this would solve all the world’s energy problems. Since this would be pretty obvious by now, and this isn’t done, I am missing something here. Even if not perfectly efficient and lose some power at each step up, seems like a solar pump could compensate for this, but again as this isn’t really done, something doesn’t add up.
I don't care if it real or fake it a dam good trick and I now have this dam video stuck in my head trying to figure out if there is some scientiic reason , when I know there is none
And for my next trick Mom Dad we have running water! It looks like he stuck it over a natural spring in the ground. That's pretty good for having no leaks and nothing is glued.
Totally credible, this is in the Southern Hemisphere so water will always want to drain to the Northern Hemisphere. Otherwise we wouldnt have tides in the ocean. :)😁
No water will flow up in a pipe unless mechanically assisted. It does not matter what specification or pipe measurements are used. Pumping at that flow and constant pressure, endless. Built the exact model, did not work. BS.
The water will absolutely flow up into the pipe. Right up to the height of the water on the outside of the pipe. Unless you plug the pipe with a schrader valve. Then no water will flow up the pipe.
No this is called a RAM Pump, and it is fed by Gravity, it may actually work, I will experiment with it more to find out. It would be neat if we could somehow make this work and then have the water fall on a water wheel which could spin up a small turbine to make power. IDK.. Just my thoughts on it. THe more water we could get to flow, the more power we could put into our water wheel and if we could get our water wheel to have enough power we could gear it up to a generator and make the generator spin at a faster rate, then it would be free Electricity. Or theoretically, I forsee a lot of issues with this though. I will experiment with it see what we can come up with.
There is one tube not addressed in the measurements, it is attached to the Valve and the V120. How long is that I know I didn't miss it, went back and looked twice? LOL.
I watched till the end, and I am amazed. Mine won't work though. I don't think my inner tube was broken enough. But hey, almost 1,000,000 views and nearly 600,000 subscribers. Not to mention over 1000 comments (plus replies). Money in the bank!
People don’t understand what a check valve does which is why he is moving it back and forth in the water. They make gasoline siphon hoses with the same valves and I use them all the time to transfer diesel from a tank to buckets for excavators.
You can put a water mill to make unlimited energy and have the water drain back to the pond. Build a hundred of these with water mill and create enough free electricity to power the city. Cool idea. Lmfao .
Notice in the beginning he's showing you the insides of the small pipes... The big one doesn't get a clear shot through it as that's the one that has the pump. The check valve is used to prime the pump, without that it wouldn't work. Next video please.
could not get in mind, why the cycle valve was fitted, what is its function, the cycle valve works minimum 100 PSI, depends upon the inner pressure, the one way water valve can work through suction by vacuum basis. Finally looks great for the people who could not understand mechanism not for the people who know how things works.
the schrader valve requires 30 psi to force it open. Water has more psi the deeper it is - so the pipe goes six feet down and is 3 inches diameter - so you get greater than 30 psi to force open the shrader valve.
It's common sense the down slop is 1/4 of the up slop. It physically doesn't have enough energy to pull the water up. And his red valve just holds the water from going back
Clearly the red thing is some sort of battery operated pump. lol. But pretty slick attempt at trying to convince people water can flow up hill against gravity with no power.
