If you have a cooking oven you can also make dry carbon fiber parts. [DIY] (Making Engine Cover)

Подписаться 156 тыс.

Просмотров 748 тыс.

50% 1

#carbonfiber #drycarbon #enginecover
If you have a cooking oven you can also make dry carbon fiber parts. [DIY] (Making Engine Cover)
How to Make a Dry Carbon Fiber Engine Cover.
How to Make a prepreg Carbon Fiber Engine Cover.
How to Make a Dry Carbon Fiber Parts
Making Dry Carbon Fiber Engine Cover
How to make a mold for carbon fiber
How to make a fiberglass mold
HANKUK CARBON
Website : www.hankukcomposites.com
Linkedin : / hankukcarbon
RU-vid : / hankukcarbon
#카본
#드라이카본
#엔진커버
만약 당신에게 오븐이 있다면 당신도 드라이 카본 파츠를 만들 수 있습니다. [DIY] (엔진커버 만들기)
드라이 카본 파츠 만들기
드라이 카본 엔진커버 만들기
카본용 몰드 만들기
FRP 몰드 만들기

Хобби

Опубликовано:

31 июл 2023

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 145

@user-wf4iz5wj2c 9 месяцев назад

가끔이라도 올려줘서 너무 좋습니다!

@danboyes7477 10 месяцев назад

Looks amazing, well done! Loving your work as always 👍

@sgsuck109 9 месяцев назад

Great video, but please wear gloves. Epoxy is bad for your skin/health and also the pre-preg will be contaminated with grease from your hands

@namrokmc7364 10 месяцев назад

와..자주보는데요. 대단하시구. 멋지세요.

@ourtorreslikestoreviewandp2108 10 месяцев назад

My experience of Laminating, would be to lay the long piece first, then put the strip around the coney part. If it’s a seen part you won’t see the join that way. Also I would cut the strip at 0-90 it’s easier to work round corners, the weave should be straight not at a 45 degree angle

@jhj7460 10 месяцев назад

진짜 많이 기다렸습니다

@hohomandoo882 10 месяцев назад

기다렸어유....진짜 영상 잘봤어유^^

@Generalusuer 10 месяцев назад

Fantastic work🎉

@mcpotx1nonly 10 месяцев назад

You need a filament dryer for your cf nylon. You won't need to sand your 3d prints anymore. Run it at 70c for 24 hours then run a ptfe tube to the printer prints will come out way nicer

@alexde4310 10 месяцев назад

Good job as always 👍

@viajando-con-edgar 10 месяцев назад

Exelente como siempre amigo!

@chrikimck 9 месяцев назад

에코님은 카카오 물티슈를 너무 좋아하심🙂

@bae_ru_ru 10 месяцев назад

포지드카본에서 드라이카본으로 새로 만드셨군요~

@abovewongart 10 месяцев назад

that's incredible

@ronbaer67 9 месяцев назад

great creativity in your project but a couple of suggestions, 1) use a fine hair like camel or horse hair brush as it leaves a better finish so less prep and 2) work on keeping even spray patterns for more even coats

@hetori9918 10 месяцев назад

Dude you are a pro

@jeromedouillere3444 10 месяцев назад

Bravo quelle patience !

@mohammadrasoulfard-habibi3066 10 месяцев назад

This legend got me into this, brilliant video as always mate.

@andihema132 7 месяцев назад

The best 👏🏻👏🏻

@neostarfromearth107 Месяц назад

nice job, thanks for sharing :-)

@user-jc8bq5eb6s 10 месяцев назад

Ну наконец то . Я уже думал ты забыл про нас ,так сказать кинул ))) .Как всегда ,видео на высоте и предельно ясно показано поэтапно. Жду новых видео ...

@ThatOneChannelinAZ 10 месяцев назад

Welcome back. your content is missed. I hope you're doing well.

@SHADOWBLACKs650 9 месяцев назад

I make them for RC bodies, you got it down correctly, except don't use the min wax, use the automotive polyurethane clear and it's a dream when finished... 👍

@jeanfrancoispoivre4438 10 месяцев назад

Magnifique ❤️

@chang5dayo 4 месяца назад

녹이나서 구멍이 길게 난 자동차의 하부에 가본으로 덥을 생각이 있어 정보를 찾던중에 들르게 되었습니다. 뜨거운 열을 가하지 않고 철에 잘 붙게 하는 방법은 없을까요?

@autogeek23 10 месяцев назад

Very nice!

@robSTI 9 месяцев назад

WOOOW TOP DIY

@gurt300 7 месяцев назад

You should not do the bagging like infusion but put the entire mold in a vacuum bag with absorbant material after the release film. And also keep vacuum during curing

@hockysa 10 месяцев назад

didn't you get an ultrasonic cutter? I thought you would use that over the dremel.

@elnolasco 2 месяца назад

Excellent videos! Help me a lot What kind of towels do you use for cleaning the carbon parts? Thanks

@Atipecomputers 8 месяцев назад

awesome

@Reddot_AUTO 10 месяцев назад

아 정말 배우고 싶은 기술입니다. 이런거 배울수 있는 국비 교육과정은 없나요?

@sofuzzywuzzy 7 месяцев назад

Have you ever done something much larger, like an E61 panoramic sunroof?

@ignantf00 3 месяца назад

great job! that clear spray doesnt turn yellow\green with all the heat in the engine bay?

@ThomasEvoSam 4 месяца назад

Hello there. I have a question What kind of mechanism you use to remove the inside air from the bag?

@junyoung458 9 месяцев назад

8:45 에폭시를 섞은 후 진공챔버에서 degasing 과정은 필요 없나요? 부품에 칠하는 과정에서 공기 기포가 어차피 들어가게 되나요?

@volare2378 9 месяцев назад

저정도 얇은 두께로 올릴경우에는 딱히 탈포과정이 필요해 보이지는 않네요~탈포를 하더리도 사실상 붓 사이의 공간을 통해서 기포가 발생할수는 있지만 도포 이후 오븐에 들어가면서 열에 의해 탈포가 되기도 할것같네요ㅎㅎ

@sonaki_custom 9 месяцев назад

오븐이 있어서 나도 하나 만들어 볼까 하고 들어 왔는데, 전문가들이 돈을 받아야 하는 이유를 알게 되는 영상!

@Alex_Artix 5 месяцев назад

Что за препрег использовался и какой плотности? И температура запекания тоже интересна

@teor7809 10 месяцев назад

기다렸습나다

@rafakalisz7761 9 месяцев назад

no no fajnie Ci to wyszło :)

@macolaiden 10 месяцев назад

Perfect You're still here ❤

@lotuselansteve 3 месяца назад

Good job, but perforated film is used for wet lay. Unperforated film is used for prepreg as the resin to carbon ratio is correct so you don't want to remove any of it.

@CarbonFiber-nd2sq 10 месяцев назад

Nice

@EliudUrba 10 месяцев назад

Interesante, crees que se pueda poner un aislante termo acústico tipo kilmat por la parte interna, a modo de que cambie el sonido, saludos

@user-be6hl5tc2t 9 месяцев назад

Подскажите хороший современный учебный материал по изготовлению карбоновых деталей

@darkwafflez_6190 10 месяцев назад

would you be willing to compile a list of materials/tools to attempt this project? I want to make a carbon engine cover for my 335i lol

@vanchaa1 10 месяцев назад

Gelcoat Black, Glass fibre staple, epoxy resin for the mould. Prepreg (dry Carbon + epoxy works also) release agent, release film, Vacuum bag, cotton flece. You also need some filler, sanding material, scissors, flex / dremel whit diamond blade, knife, wooden wedges etc.

@joscythe556 9 месяцев назад

I advise you to use non-perforated release film to prevent dry spots and pinholes in you parts. There wouldn't be a point in using perforated film without a bleeder cloth anyways. Also it's advisable to use a breather cloth over your non-perforated film to get a better vacuum.

@thecarbonfibernation 5 месяцев назад

To add to this point, pre-preg materials have a carefully controlled resin to material ratio in order to optimize strength and weight. Using perforated release film removes resin that is needed for the material to cure properly. Resin starved parts are brittle and subject ro cracking.

@shanyebyt4899 9 месяцев назад

How much would something like this cost, material wise, if i were to do it myself? Thanks.

@ariklotia3958 9 месяцев назад

Ok can you explain why the first time you put item in the heater your numbers staid the same compare 2nd time your numbers were cleared out… I could only image you’re it using that small heater..

@Samuele.Deganello 9 месяцев назад

Hi Philip wellcome back😉... this system is very good but in my opinion you not learn to work... i things this that too too simple. But i think it an very good system for the big industry where production times are of the essence. in any case great idea😉

@bigcar_kr 10 месяцев назад

언니 살아있을줄 알았다구!!!!!

@ilanSniping 8 месяцев назад

What clear coat is that ?

@user-ol3pu8hg9j 10 месяцев назад

형 살아있었구나

@pb6839 9 месяцев назад

Spray with the spray can at 90° so that the paint layer is even

@user-pf6nb3vn1i 10 месяцев назад

0:46 Prepreg Carbon Fiber (Dry Carbon Fiber) 안녕하세요. 프리프레그도 드라이 카본이라고 표현을 하는 건가요?? 드라이는 레진함침이 안되어있는 상태일 때 쓰는 용어인 줄 알았는데 궁금합니다~

@ECOLAPStudio 10 месяцев назад

안녕하세요 말씀하신 것이 맞습니다 본래 레진함침이 되어있지 않은 상태의 카본섬유를 드라이카본이라 부르는 것이 맞습니다 하지만 자동차쪽에선 프리프레그로 만들어진 파츠를 드라이카본이라 부르고 있습니다

@user-pf6nb3vn1i 10 месяцев назад

@@ECOLAPStudio 아 그렇군요 처음 알았습니다. 항상 좋은영상 감사합니다.

@volare2378 9 месяцев назад

프리프레그카본은 레진으로 도막층이 형성되어있지 않아 드라이카본이라 부르는것 같아요

@sniperkotakelor 7 месяцев назад

I want to know what is the name of the carbon material used in it

@sewerynbudziszewski8219 9 месяцев назад

czy piekarnik do pieczenia też się sprawdzi ?

@nunuland69 9 месяцев назад

What's your opinion on the prepeg dry carbon fiber then resin infusion? Is dry carbon lighter? I feel from watch your vids that carbon infusion is easier to manipulate into tight spaces than prepeg c.f. thanks!!

@user-ul7el1lo4r 9 месяцев назад

Легче и крепче.

@AndrewKay-fg1bj Месяц назад

And this is why carbon parts cost an absolute fortune, very labour intensive

@bluelake777 10 месяцев назад

늘 기다리고 있습니다

@deniskablukov4404 7 месяцев назад

Выглядит красиво, но меня волнует крепление нейлоновых ножек. У полиамида достаточно тяжело клеиться. Вы же используете эпоксидную смолу. Я пробовал также клеить издели из полиамида, только они были армированы стекловолокном. Результат был плохой. Все выглядело хорошо, но при небольшом усилии весь клеевой слой откалывался

@thomashellstrom9514 2 месяца назад

👏🏻👏🏻🤩

@user-dg4bb5td7q 10 месяцев назад

바이크 카본휠도 만드실수 있을듯 합니다.

@user-fn3iu1ty6n 10 месяцев назад

오이오이!!!! 기다렸다고!!!!!!

@user-gc4yn2os2n 8 месяцев назад

Где купить такой карбон ?

@premiumannelie4474 9 месяцев назад

Respekt !!!!!

@thenka197 7 месяцев назад

Where do you buy the carbon I need to order some..???

@3toedSloth75 9 месяцев назад

Should use sealed, not perforated, release film with prepreg. Otherwise, some of the "perfect ration" of resin will leak past the film and cause voids (pinholes, etc.).

@joscythe556 9 месяцев назад

Exactly, also there is really no point in using perforated film if you don't use a bleeder cloth.

@sttm1283 10 месяцев назад

why all the creases(wavyness) on the sealant tape? wouldnt it be better to just lay it flat? nice engine cover... nice work.

@seadog9534 10 месяцев назад

The bag would bridge if enough slack is not present

@user-dg4bb5td7q 10 месяцев назад

마지막에 3D프린터로 만든 마운트는 오래 못버티지 싶은데요 카본으로 한번 더빵 했으면 완벽했을뜻

@johnrichardson82 2 месяца назад

Where do you buy carbon fiber like this video has

@vanchaa1 10 месяцев назад

Do you use any protection on your hands? We never work whitout gloves on prepreg. It still very hazardous

@sdasclk1861 7 месяцев назад

😂

@stevebell3537 6 месяцев назад

Not so much the hands but breathing it in

@user-ci4cj5eq4x 9 месяцев назад

What's going to be made next?!

@francescobarone4443 9 месяцев назад

I hope in a tennis raquet😊

@Karma_Gear Месяц назад

great video,but where is my Mpower

@vinkenwood8233 6 месяцев назад

Suché díly? Ony se daji v troubě vyrábět i mokré díly??

@mark675 10 месяцев назад

The 3d printed mounts in a high temp environment? Hmm

@user-ys5ws5sw2k 9 месяцев назад

Крутяк

@sergioveron8018 9 месяцев назад

Haces llanta de bicicleta r.28?

@Phoenix_0777 7 месяцев назад

Please, fix retracts on your ender 3...

@meanza666 9 месяцев назад

Can you make a motorcycle frame for me? I like your work.

@baesundal 10 месяцев назад

카본 섬유는 어디서 사야 하나요?

@user-pf6nb3vn1i 10 месяцев назад

소량구매하시는거면 인터넷사이트 '화이바맨' 이나 'FRP 샵' 에서 구매하실 수 있습니다.

@alfalfasprout69 Месяц назад

Is this master at work in side his house?

@MyStiiX 10 месяцев назад

Babe, quick! Eco-lap just uploaded a new video

@kevinkev1530 10 месяцев назад

👍🏾👍🏾

@TANCOR1108 14 дней назад

Ни чего не понятно, но очень интересно! 😅

@Markelboomin Месяц назад

Why so many layers (legit question)?

@user-hd2hp7qn4k 10 месяцев назад

엠포도 좀 보여줘요 ㅠㅠ

@GregNFresh 7 месяцев назад

Trop de travail juste pour une pièce comme ça et qui en plus ne se voit même pas car elle cachée sous le capot.

@user-kv8mu5td5h 9 месяцев назад

손이 좀 탔네요 ㅋㅋ

@JuanTorres-ly1rq 6 месяцев назад

Can we request part. And if so would sell it back to me😅 97 lexus sc400 center console

@Trumppower 10 месяцев назад

Better buy a Easy Composites Oven and Pump if you want to do this right. It's too expensive to make mistakes with this material.

@lotuselansteve 3 месяца назад

Agree with a decent pump, but the EC oven's base price is over £1700! A standard oven works well if you use a digital temp sensor to monitor the temp.