Important UPDATE and PROBLEMS with My Vatrer Lithium RV Battery! 

James, I have no doubt about your honesty and integrity. There are so many examples of the lengths you go to - to make things right for your clients. I just wish you, or I, were closer in proximity than Arizona - Nebraska lol. That being said, I have watched a great deal of your content here on RU-vid and can say without a doubt how much I appreciate it. Your content has helped me in so many ways with my own projects on my own camper. A lot of content creators wouldn’t necessarily be as up front open and honest about mistakes they may have made, or subjects they weren’t as knowledgeable on AND the things they have learned along the way to success. You literally tell us everything you go through to make that success happen, even if it’s simply a suggestion a commenter makes and you decide to utilize that suggestion. I honestly believe if I needed the advice I would be able to find it in your list of videos somewhere lol. Between your channel and the RV Works channel, I believe you 2 are THE BEST rv techs in the country. Thank you so much for the support, advice, information, struggles and honesty and integrity. You have been a great help indeed !

Working in the electrical field, one of the items we would do was an infrared survey. What this showed was loose connection. We can apply this to the RV's. One suggestion is to check all electrical connection in your RV or have someone qualified check. You'll be surprise at what you find. It may Keep you and your loved ones safe.

Thumbs up 👍 to the viewer that spoke out. 😊

What about putting an Adel clamp on that cable to support it and prevent it from trying to turn against the terminal lug?

I guess the dirt road to the hot springs is taking its toll on the RV. 🤣🤣

Been 6 months already? Time flies

I know that I've used battery impact tools before and relied on them to torque the nuts down. I've found out the hard way, that is not a reliable method as a weak battery will sound like it did the job. It is always better to check with a torque wrench for critical connections.

Shouldn't the vents be open to vent heat?

Your title scared me until I watched the video. I am in the middle of my Vatrer installation. I can live with the Blue tooth limitations. I am currently struggling with connecting my Victron Dc to Dc charger. I think I am going to connect it to the chassis battery cable where it terminates right next to the house battery cable on the back of a breaker box within the battery compartment. On the other side of the wall are a chassis battery shut off ,an inverter shut off and a breaker panel. I just got this 2019 Tiffin Phaeton 37 BH. Batteries were 2018 dates so decided to go with the Vatrer after watching your upgrade. Keep up the great videos!

Great info James! Just as an FYI from a Victron installer :) The settings via Bluetooth will override any of the dial settings. And all settings are available via the Bluetooth. I never mess with the dial, just program via the Bluetooth according to the system requirements and the battery mfg recommended parameters

My Rover went came bad also. They just sent me a new one at no charge.

Great informaton! Enjoyed the video. We just got our 2019 Tffin 45 OPP and I am researching and planning my solar setup. Thank you!

Just a thought.On your positive cable that was loose, why not install a adel clamp ahead of the terminal a few inches to relive the pressure and movement of that cable at the stud. May be over kill, but very cheap and simple thing to do and eliminate one more thing that could cause problems down the road. I REALLY like your channael by the way..

Completed my vatrer 460 and dc to dc charger today. I would post a photo but I cannot figure out how to do that. Thank you for the inspiration, James.

Look forward to every video,makes my workday go a little quicker watching your videos in my crane.

As a 35+ year Auto mechanic and business owner I love and appreciate your videos. I think we would all like you opinion on SOLAR GENERATORS. Like you I do things fast and easy but safe. LOL!! I use an Anker f2600 with one Aux battery for a total of 5200+watts of power. I also have a VATRER 300ah battery as my 12v system. I have my Converter breaker off. This makes a split system. My shore power is connected to the Anker for 110v. 400w solar on roof charges the Vatrer. Also I have it wired so I can slow or fast(600w)charge my Anker from the Vatrer with a 12v to 48v UPCONVERTER. Works awesome. Basically it's a total of 8200w of power and 600w solar with my Anker 200w panel. That set up was less than $3500 and I can run 1 AC at a time for hours. Yet Facebook groups like to poo poo my system. What do you think? It would cost about $10+k in Victron system for what I get.

Hi! I’m new here and love the practical information on batteries! Cool motor home and shop setup!

I use that same lifpo BIM on my Transit based B+ with about 70 charge cycles in 25,000mi of driving with no problems. It's been a great solution for me. Thanks for your videos they helped me inspect my RV and maintain it. Thanks again!

I did not know that the victron cc had to be set to 7. I think that has been my issue all along! Thank you! I only had it set the setting in the app

Another great video! Thanks for the update.

Appreciate your videos. I Look forward for your content. I also appreciate backseat drivers.LOL

I just ordered 2x 24v DIY Lifepo4 battery cases for my 306aH EVE cells, and I'm going to set up a weatherproof 15kWh "solar generator" on a trailer hitch mounted carrier. This way it can be moved from my travel trailer to the Monaco and then to the Navion depending on the needs of the mission.

James, Thanks! I have spent the last few days pulling my hair out within the victron settings menus! Couple clicks of the screwdriver and now she is humming! Appreciate all the tips!

I think I'd add a P-clamp on that positive cable so the cable flex would not apply torque on the terminal.

The battery is a giant heat sink so would a very long time to warm up. Also the moisture meter might be right, condensation with it closed up tight...

Nice update and keep the videos coming James

I, too, went to a Victron 100/30. I'm going to a 12V air conditioner for my Arctic Fox in bed camper. It's only 8000 BTU's, but be fine.

For a follow up it will be great to add a cable clamp on that cable to take any pressure off of the nut and connection.

Wouldn’t it be easier to take that backboard? The TV is plugged into or connected to mounted on I mean and put a hinge and a hinge lock type swing arm on your backer board there so that way you can open and close not only the TV but you can open and close the board. That’s the TV connected on.

Always wondered just how far the Bluetooth could go with the antenna stuck incident a metal case.. To bad you can't slip into the bms and solder a small coax to internal antenna then run it out of the box to an outboard antenna , that could help a lot

👍🏻

I thought you were aware of that connection and this was a work in progress

👍

Are you sure there is not a cigar humidor built into that battery? That is the same temp / humidity Guage that would be on one!

Yes bluetooth is weak about 12’ in my fifth wheel.

Consider an insulated clamp just before the fuse holder and a slip on abrasion cover on the wire where it is against the wall. Lots of truck and bus fires from cables rubbing and shorting. Just a thought, appreciate your work your just across the country from me to be able to use you for repairs :{

I had a 1996 34' Safari, almost identical inside. That battery cable that was loose will become loose again if you do not attach a strain relief to the wall so there is not rotational pressure on the cable when the battery tray is moved. Cheers.

I have all Victron components in my set-up and the Bluetooth stinks. Works haphazardly in and out and is super frustrating. Only my MPPT solar charger will work from the drivers seat.

Take the tape off the vents of your batteries and I bet the moisture content goes down - lol.

I have the same Renogy charge controller that wouldn't work your LiFePO4 battery. It has been charging my 300 amp hour system flawlessly for 2 years. Maybe you just got a bad one.

Hey James, long time no chat! Hey just an idea if you wanted to add more Vatrer to your battery compartment. Perhaps you could build a second deck/level on your sliding pull out battery tray. This way you could put more Vatrers on the bottom and move the Rig batteries onto the second deck you will build? What do you think? I know the rig batteries are way smaller than the Vatrers so that may be an idea how you could add more Vatrers without moving the operation to another compartment! Anyway just a thought while I was watching this latest vid! Cheers! Michael

Have you called Renogy? I hear good things about their customer support. (But I do like the Victron gear!)

The voltage was 14.2V at 17:50 so the battery is basically full. That SOC reading on the shunt should reset to 100% once the amps drop off.

James I have a question for you I have a 1999 Georgia boy Landis. It has a Q55 generac generator I need a choke switch it has 3 wires go to the switch and can't find a switch to replace it what else can I use will a 3 way switch work and I also need the left and right windshield wipers for it and the rear ladder seems lose what can I do to tighten it up

Ditto re Bluetooth range being an issue. My Victron Smart Shunt, in my battery compartment, has a range not quite sufficient to get to my seat at the dining table. I have to stand in the hallway leaning on the bathroom door are yields and just lay over the foot of the bed while I read it.

Maybe if the BMS wasn’t inside a metal battery case the Bluetooth range would be better 🤷🏻‍♂️

Thanks for sharing. Like 818

Hi this is Jared in Bullhead City AZ. I'm originally from Utah. Since we've been in AZ, the heat has been really hard on my 2 engine batteries. Yesterday I replaced them with 2 brand new duracell 65 batteries same make and model as what was in there when I bought it. I labeled connections and reconnected them as they were but it keeps arching and sparking when I try to reconnect the cables. Is there something I need to switch off or is there a sequence while hooking up the new batteries? It's literally melting my post on the new batteries. Please help!

I don't know if they work, but apparently there are bluetooth repeaters for sale.

Blue tooth booster?

That red + cable needs to be mounted down, the weight of the wire wiggling is loosening up that nut over time.

That fuse should be a class T fuse, I cannot tell what it is, but other classes of fuses are not a high enough rating. lower rating fuses will actually liquify the metal in the fuse and arc across the metal vapor.

Awesome catch by the viewer! Did it break-loose even with a washer + lock washer? Or was it missing the lock washer?

Put a cabil strap on the cable and it will stop moving on you

In the opening scene... Isn't the slide going to take that smoke detector down? Based on the camera angle, it looks like it will.

Yeah, my Bluetooth won't reach more than 5'. It's pretty bad, and I've let Vatrer know about it.

Maybe tell people you put the terminals on the inside because it would be harder to steal.

My 460 Vatrer House battery charges fine with my 20amp Renogy. hmm?

Torque wrench, fuses and strain relief……

Considering that bluetooth has a max theoretical range of 10m, 33feet, then I'd say you are getting a fantastic result. All the metal in between will hinder performance

Had the older Renogy 30 amp controller. Not pleased. Bluetooth never worked correctly but lived with that as it wasn't a big deal. Final blow - controller died after 18 months! Of course out of warranty. Contacted Renogy, no assistance as they won't repair them!! He suggested I try an electronics repair shop. Threw it in the trash and bought a cheaper unit that is still working years later.

Whoa whoa whoa 😮😮 4:30 you are professional installer and you should know better to have more than three wires on that ground. You need a bus bar and ideally you would have a shunt in between that negative background and your needed busbar for all your grounds.😮😮😢