Incredible Equipment Trailer Restoration 

Thank you for not just talking the whole video. Your work speaks for itself, no need for filler like other channels. Keep it up.

Nothing is more satisfying than seeing a project like this come together. You did a excellent job.

Beautiful job.

Nice refurbish I like the look of the wider boards on the outside, I used old motor oil to stain mine worked well plus free, if you use diesel oil it gives it a nice dark stain finish

Great work man! You killed it with that restoration. Trailer looks awesome. Can’t wait to see it hauling stuff around. Nice single cab GMC pickup btw!

You did a great job, there will always be those that will have something negative to say. As long as you’re happy with it that’s all that matters.

Looks great, only thing id change is the safety chain quick links. They have a very low weight rating (probably 3500# or less each) and wont safely control the trailer if loaded to the trailer limit in an emergency. A shackle in that position would handle a much larger load. Otherwise great looking trailer and nice video.

Good work! Can't wait to see more of your content as time goes on!

Killed it!

There's two different wiring color diagrams for RV 7 pin and trailer 7 pin. It's a screwed up system and a piss off every time you try and color match. There's no standard, some RVs use trailer color code and some trailers use RV color code.

Having your own sticker is a nice touch

It turned out awesome!

Nicely done

Turned out real nice!👍

Nice work on your restoration, looks great 👍.

Nice job, only thing I noticed is those connecting links you used on the safety chains are not rated for high loads, I would replace them with something stronger.

Looks awesome..!

Bad ass set up

We have gone to running carriage bolts through the decking next to the frame member and using a hd fender washer to grab the lip of the frame...no frame drilling required and you can use an impact.

Great work man, excited to join in on the channel early and see you grow. Trailer looks fantastic! My only advice would be to slow down your time lapses just a tad and mix in some more talking points during those like “Okay we’re about to paint … time lapse … okay painting is going well etc… time lapse.. I think that would help a lot. Good work man!

Looks great!

Great work man nice video keep up the good work god bless

Nice job!

Good job MMR!

Looks great 👍

good dam job little buddy

There is a kit that is available powered by a 12 volt dc motor that will wind your jack up and down and is relatively easy to mount ! CT3 added one to his equipment trailer and was pleased with it's operation !

Killed it broski

Awesome job

Great job, subscribed 🤙🏻

Probably be a lot of work but you could weld nuts to bold deck too

Nice rebuild and decal! Should sell quickly!

Badass bro great work would you consider getting a hydraulic or electric jack in the future for that trailer?

reflective tape must cover 50 percent of trailer length

Little music overlay would make these more enjoyable just a tip.

I would adjust the hitches for a slight positive rake when empty so when it's loaded it'll level out. That's just me

This does not help you since you have fixed the wiring. But there is a difference between trailer wring and RV wiring. A lot of those junction boxes are wired RV style...

Good video. Need bushings? 😊

How about the brakes and bearings how about the bushings and the equalizer i bet they were hammered out and the magnets probably are worn out

Looks Good To Me

Looks good to me. Do you restore to sell?

Use stainless steel self tapping screws.

Helping my brother redo his 26 ft car hauler soon we are thinking of using expanded metal for the deck .. probably more expensive but will last longer and easier to keep clean .. Thoughts anyone ?

Needs a hub cap over the lug nuts. Great job though.

Nice content, could use some music, too much dead air, but the video and editing are great!

You said something about staining it put old diesel and burnt oil on it

? Will the rust come back through the paint.

What did you deck it with?

This was excellent. appreciate your content. Keep up the good work.

Well we know 1 thing for sure, those electrical wiring won't last leaving them exposed like that

I was liking it till 8 saw yo7 only installed 1 carriage bolt per board, probably gonna see some cupping in the future. 2 per board would’ve been better. Great video tho

Coat those boards with old motor oil after they dry out in a few weeks.

Only mistake I see is grounding each light to the frame, should of ran all grounds to one point, much easier to pin point issues.

Might help to have some background music

Tidy job. As for the paint job, it's a working trailer not a car!

Been think about doing this and this video made up my mind on going ahead an doing the same thing