Inline exhaust for better laser smoke extraction

Подписаться 16 тыс.

Просмотров 4,8 тыс.

50% 1

Having good smoke extraction can greatly improve the quality of your work, and keep the smoke and vapors from dirtying up your laser, causing you more downtime and less efficiency. Using straight walled pipe and an inline fan will greatly improve airflow and hopefully allow me to run two lasers from one fan while still extracting all the smoke. Check out this video to see how I did it.
Want to use these files for your own setup? You can grab the files from my Etsy shop here: vintaurisworkshop.etsy.com/li...
Follow me on Instagram and Facebook for behind-the-scenes on what is happening in my workshop!
/ vintauri
/ vintaurisworkshop
vintaurisworkshop.etsy.com
www.amazon.com/shop/vintauri
Items used in this video. Some links will be affiliate links that provide a kickback to this channel at no extra cost to you. This is a great way to support this channel!
xTool P2 laser - www.xtool.com/products/xtool-...
xTool S1 Laser - www.xtool.com/products/xtool-...
xTool F1 Laser - www.xtool.com/products/xtool-...
Hon&Guan 6" Inline Fan - amzn.to/4a0H7EX
Use Code "Vintauri" for 10% off this fan on Amazon from 3/26/24 - 6/30/24
4" Blast Gates - amzn.to/3VoKyAO
Aluminum Foil Tape - amzn.to/4ciAVd2
6" x 4" Reducer HVAC Reducer - amzn.to/3IFwxal
Electrical Tape - amzn.to/3IHCyna
#laserengraver #lasercutting ‪@HonGuan_official‬ ‪@xToollaser‬

Развлечения

Опубликовано:

16 мар 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 48

@Samcraftcom 4 месяца назад

I have the same exact fan, it works very well with the exception of being leaky on airflow around those clamps and the backside. Tape the devil out of it to seal it up and you'll never have any issues. The one fan runs all of my shop's extraction: 2 CO2 lasers, diode, and 2 galvo lasers.

@Vintauri 4 месяца назад

Thanks Sam, I was going to ask you what fan you installed as it seemed to work very well in your setup. I'll be doubling back and adding some tape around it to ensure I'm not getting fumes leaking out.

@guynotes777 4 месяца назад

I agree I have one like this and it is no where near air tight enough. Now it could be that I gave it set up like host with 4 inch going to the 6 inch fan then out to a 4 inch exit vent. I have taped it with painters tape as I don't want to make it too permanent. Great video

@minnesotamaker1846 4 месяца назад

Nice and clean install.

@Vintauri 4 месяца назад

Thanks! Every little bit of shop organization helps keep things easier to use and thus keeps my motivation and productivity up!

@sannyassi73 4 месяца назад

Nice exhaust setup!

@Vintauri 4 месяца назад

Thanks! It’s working well so far!

@JeffBenedict 4 месяца назад

Awesome setup. Great work.

@Vintauri 4 месяца назад

Thanks! Hopefully it helps me with being more productive and less shuffling things in the shop.

@htl-customs 4 месяца назад

Awesome video! I will need this as a reference later.....I have a long wall that everything will eventually get set up on. Great info!

@Vintauri 4 месяца назад

If you have the room go with 6” piping right away. It will help maximize the airflow and allow more machines to be added.

@ScottKershawRX 4 месяца назад

Excellent!!! This is super helpful!!!

@Vintauri 4 месяца назад

Glad it was helpful! Thanks for watching!

@kevinjensen9817 4 месяца назад

Nice and clean. I like it.

@Vintauri 4 месяца назад

Thanks! Every little bit of shop organization helps!

@MWE-693 4 месяца назад

Thanks for the topic, I have been looking forward to seeing modifications to the S1. I am running an AC Infinity 4" with good results, though I plan to remove the internal fan in the near future as is offsetting the true potential of the inline. Please keep us posted if you remove the fan from your machine.

@Vintauri 4 месяца назад

If I work out a way to remove the fan without erroring out the laser and hopefully not voiding the warranty, I'll be sure to share that. I'd hate to recommend anything that would cause people issues with support of their machine, and if I do, it will have a big disclaimer on it.

@celton58 3 месяца назад

So, what about flame detection and auto fire suppression with the inline fan? I have a similar set up on my S1, but have not yet figured out a way to shut it down during a fire (without hitting the fan switch manually). Had a fire on my D1 and forgot to hit the inline fan switch, so sucked all the fire suppression before putting out the fire. Had to turn off inline fan manually and hit it with the fire extinguisher again. Cooked my wiring, but no damae to the laser head (just luck though).

@brittond14 4 месяца назад

likely putting less strain on the motor as long is heat is dissipated enough to cool motor windings.

@Vintauri 4 месяца назад

I’ve been running a similar setup in my basement shop for over a year and while that does not seem heavy use, it’s not failed me yet.

@robmills4709 4 месяца назад

Great solution Steve, i have a similar setup, though not as neat. Is the bracket file available, brilliant idea. I've forgot so many times to open gates.

@Vintauri 4 месяца назад

I've just added them to my Etsy shop! vintaurisworkshop.etsy.com/listing/1698178253

@balahmay 3 месяца назад

Nice clear explanation. Just wondering if there is a check valve at the outside to prevent wind forcing its way in?

@Vintauri 3 месяца назад

I have the typical flap on the outside that opens when the fan is on, but it can also sometimes open a bit if the wind is right. It would not hurt to put another blast gate or valve at the exit to provide another barrier if you feel the need.

@timahrndt2496 4 месяца назад

Good video, looks great. Do either of the lasers have any filtration before exiting the enclosure? I have my Ikier 48w in a homemade enclosure, cutting and engraving created so much smoke that the inline fan and the screen outside the garage actually became clogged with smoke residue. My solution was to use A/C filter cut to cover the 4" exhaust flange inside the inclosure. It takes about 20 seconds to replace it and when I have a pile of dirty filters, I just wash them out in the sink and re-use. They do a great job of keeping all the smutz out of the inline fan and exhaust port.

@Vintauri 4 месяца назад

I do not run any filters on this setup. As you’ve noticed you do have to clean the fan and outlet or it will build up residue from the smoke and vapors.

@GeraldJensen 4 месяца назад

Good video ... comes at the right time! I just finished an enclosure based on the plans on your Etsy site (mine is larger to accommodate my ATEZR P20), using a 195cfm fan from Vivosun. Right now, I am running a flex hose out under the garage door, but plan to run metal pipe through the wall later this spring. A file to cut pipe supports would sure come in handy (SVG or Lightburn)! Any plans to add that to your store?

@Vintauri 4 месяца назад

Yes I'll be tweaking the clamp files and will have them available soon. You'll like the increased flow from straight smooth pipe over the flex hose. Thanks for watching!

@Vintauri 4 месяца назад

vintaurisworkshop.etsy.com/listing/1698178253

@GeraldJensen 4 месяца назад

Thanks!@@Vintauri

@jackhelm9852 4 месяца назад

Very nice. Do you have the plans for those clamps anywhere? They look so much nicer than the straps.

@Vintauri 4 месяца назад

I'm going to make some adjustments and also sort out the 6" size and then I'll make them available soon.

@Vintauri 4 месяца назад

vintaurisworkshop.etsy.com/listing/1698178253

@donepearce 4 месяца назад

I think the big improvement would come from some inlet vents along the front face of the machines.

@Vintauri 4 месяца назад

Yeah that may help, the P2 has some inlet space on the lower front where the crumb tray slides in and the S1 with the riser has lots of area where air can leak in. But having some air pulled in from the front would definitely help.

@chrisr1241 24 дня назад

Thank you! Very nice video… but why do you have a s1 if you have a p2?

@Vintauri 24 дня назад

I find that diode lasers can give a better engraving on some materials compared to the Co2 lasers, while the Co2 excels at other things like acrylic. It’s nice having options and the ability to run multiple jobs on separate machines.

@KnotboredWoodworking 4 месяца назад

Did you already have the 4inch galvinized pipe before you added the 6inch inline? I know youre aware that you lose alot of CFM because the pipe isnt 6inches. Using 4inch pipe out of each laser into the 6inch main would be perfect. It still looks better than mine with black flex. I had to cover the end with fine stainless wire mess to prevent birds or wasps making nests against the damper.

@Vintauri 4 месяца назад

Yes I already had most of the 4" piping from my previous set up. So before spending too much on extra piping I thought I would see how it worked out with this. I also might move things around and then I'll look into the 6" piping as it will be much better and might allow me to add more ports for other lasers as well.

@sharonsimonson5392 4 месяца назад

Do you have a link for the elbow at the front exhaust? I’m looking to do a better exhaust system for when my M2 30W gets here. I’m planning to vent out the window.

@Vintauri 4 месяца назад

Here is one on Amazon - amzn.to/43yMqch Or Home Depot - www.homedepot.com/p/Master-Flow-4-in-90-Deg-Round-Adjustable-Elbow-B90E4/100033952