Interchange Comes To The Piedmont Southern (200) 

Congrats on your milestone. Really useful info on bending hard board.

Hi Larry. Happy 4th of July (up the British!).

Nevermind, Larry. I just discovered Video #187, which answered my question. Thanks.

Congrats Larry. I really enjoy your videos.

Larry, CONGRATULATIONS 🎉 ON THE 18,000+ SUBS. Though you may wish to update your Subscribe Promo clip from 2K. Also a change you could have made was to install a lower deck to ceiling hard board wall covering. Then you would have your entire backdrop surfacing in place, and not have to piece meal two backdrops. Also you could have used your temporary chipboard clamps below and above the hard board surface. Eliminateing the need for plastering repairs. Still and all I'm anticipating the development. ~Jim

Thanks for sharing the information in video

Hi Larry, congratulations, both with your RU-vid milestone and your very promising layout extension. Certainly the research you showed add to the level of interest of the whole Piedmont Southern. Am already looking forward to your next video reports on the progress.

Thanks Larry;

Thank you for including the history of the short line and Tye River and your plans for operation. It’s so helpful to know the ‘why’ behind the design.

Congratulations on your 200th video! Three days ago I got my first DCC starter set, a Zepher Express, even though my layout is a very small switching layout for one loco. My Walthers Plymouth now runs smoothly at very slow crawling speeds. I also did my first DCC conversion, putting a Tsunami2 TSU-1100 and speaker into an old Proto 2000 SW9/1200. Whew! I had to remove the cab interior for the speaker and the extra weight for the decoder, but the results were worth it. I can now have very authentic sounds when I'm in the mood. I'm sure that your library of videos will be a great resource for me. Cheers from Wisconsin.

that is so cool, 18k and 200 videos.. all I can say is thank you for your helpful videos.. you help a lot and help me look out side the box of what I know, and what I can do . thank you

Great Job Larry Happy 4th to you and your family

Hope you have a happy and relaxing Fourth of July Larry. It is really great to see more of the Piedmont Southern. I was very impressed with your Method of bending the Hardboard around such a sharp Curve, I ‘d seen it on the Module but this was another level of Magnitude, I bet your Heart was in your Mouth when you started to bend the Backdrop…….Thanks and Keep safe.

Congratulations on your 200th video and you have helped 18,000 very grateful subscribers, of which, I have been for a very long time. You always supply such useful information and have saved me from quite a few headaches. Thank you.

Thank you for your constant stream of high quality content. Looking forward greatly to the new expansion.

Hi Larry you have the advantage over most of us in the UK as you have a basement with seemingly unlimited space, the best we get is an attic with hot and cold temperature variations.

Hay Larry : Much Congrats On Your 200 / 18 K Achievement; Knowing That We ALL Appreciate Your Time and Endeavours ! Your Videos Certainly Are A Valued Reference Resource For MR-ers; Old ( Me ! ) and New. Much Thanks and Cheers For Now / John

Well done the history of Tie line is pretty cool happy 4th to you

Thanks for another great video. Have a happy fourth

Larry, another nice informative video as usual!

Congratulations Larry on hitting two milestones!

Atta boy number 200. Thanks for sharing.

Congratulations! Here's to another 200!

Congratulations Larry!

Hey Grats Larry! such a great learning resource too. I look forward to learning more from the next 200. PS. i hope that's ammonia free windex?

What makes the windex significant in soaking the board to bend instead of water or something else? This is something that I will have to remember when I start building my next layout.

Hi Larry: Never thought that Hard board could be curved so sharp. I have a similar outside corner to do. Seeing how you made the bend has giving me some idea as to what will be needed to accomplish the bend. If this works I will try it on the 180 D bend at the end of the peninsula. If you have any other suggestions please let me know. thanks so much for your very informative vidilos.

Larry: Does the Windex trick work with doing both concave and convex bends? Much obliged.

Can the curvature be reversed for an inside curve

What is the best track to use for HO kato or atlas

First!

What is the thickness of the backboard?

Sound continues to be murky. Consider a better microphone.