Iphone 11 Battery Health 100% using JCID V1SE, How To Remove "Important Battery Message"

Подписаться 1,7 тыс.

Просмотров 24 тыс.

50% 1

Iphone 11 Battery Health 100% using JCID V1SE, How To Remove "Important Battery Message"
In this video I show you all how you can replace your battery on iphone 11 and reset your battery health back to 100% using the JCID V1SE tool.
Timestamps
00:00 Intro
00:10 Remove battery
00:30 Remove BMS board
09:55 New Battery
12:15 Solder Bms board
18:20 JCID chip
23:25 battery health 100%
#iphone11 #batteryreplacement #importantbatterymessage #howto #repair #fixed
@phonerepairmaster9787

Наука

Опубликовано:

9 июн 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 29

@LevanjilSanktifye 7 месяцев назад

Good job.😊

@phonerepairmaster9787 7 месяцев назад

😊

@francartcedric 2 месяца назад

Magnifique 👍

@tacticalgamerat3745 5 месяцев назад

After i do all of this can i remove the jc flex cable? And will the percentage remain 100?

@phonerepairmaster9787 4 месяца назад

Yes 100% , no remove jc flex

@blackrepairs5978 2 месяца назад

I have an iPhone that will keep showing the old data at 88%, I have tried connecting a different battery, rebooting and reconnecting the new battery with the transfered bms board again but to no avail. The new data won't show up whatever I do, have you come into this? I have done many replacements without issues with the same tag on. Thanks in advance for your reply

@rtafadar 19 дней назад

you should flash the device which would also flash the battery. You can use 3utools and select quick flash and then once u press flash it would prompt u to flash the battery health percentage which u tick off. Make sure the device is backed up as the flash would erase all data off the phone, and have icloud details on standby for when u restore the phone.

@janmatejcik7073 4 месяца назад

@Phone Repair Master Hello, nice job! can you please confirm if this will work: started with bought a new battery with bms, old battery with original bms coded to iphone. When I switch the bms between them (welded) and connect the new battery with the original bms using jc flex to the phone (cycles 0 and health 100 set to JCID V1S) and then I would use the old battery with the bms from the new battery to reset the phone. And finally connected the new battery with origo bms and jc flex, will it be there 100%? Will this work please? Thanks

@aintthatthetruth69 4 месяца назад

With the tag on flex installed and old battery board swapped, boot the phone with an iPhone charging cable. Then after it loads it should show 100% in health. If you do not start the phone with the lighting cable for the first boot it won't work.

@shahyerukh7263 4 месяца назад

What is the liquid u used before soldering plz? 12:03

@shahyerukh7263 4 месяца назад

12:23

@phonerepairmaster9787 4 месяца назад

Soldering acid

@Oprafoun 5 месяцев назад

Hi, is tag on flex reusable?

@phonerepairmaster9787 5 месяцев назад

Yes

@odoyewukobby7242 5 месяцев назад

The blue little board what is it called?

@phonerepairmaster9787 5 месяцев назад

Welding Sleeve Set Battery Repair Clamping Battery Cable Layout Mold

@odoyewukobby7242 5 месяцев назад

@@phonerepairmaster9787 thanks

@alangordon6461 7 месяцев назад

What if you dont have a second battery to false start

@phonerepairmaster9787 7 месяцев назад

then fail to do with procentage

@gamurrrrr7898 5 месяцев назад

Why u used the another battery before??

@sinykrif2092 5 месяцев назад

I was wondering about that too but i think you need to do it for it to like not read anything cz the batt is dead (the old one). And when he put the new one It can read 100% with no prblm