iPhone 13 ProMax Battery Replacement-NO IMPT BATTERY MESSAGE; TAG-ON NOT NEEDED Using W09 Programmer

Подписаться 861

Просмотров 1,6 тыс.

50% 1

Another battery prpgrammer that removes the important battery message and resets the battery health percentage to 100%. You won't even need a BATTERY TAG-ON Flex. There are PROS & CONS to this repair. What are you thoughts? Comment down below.
#iphone #iphonerepair #batteryreplacement #w09pro #batteryreplacement
Thank you for Watching...
LIKE...Share....Subscribe 👍🏽

Хобби

Опубликовано:

15 фев 2024

Ссылка:

Скачать:

Готовим ссылку...

Добавить в:

Мой плейлист

Посмотреть позже

Комментарии : 23

@yourclips9974 5 месяцев назад

i hope your channel grow so fast...😊🎉

@DaKabayanTek 5 месяцев назад

I hope so too. Thank you and hope u subscribed.

@MrDinakdakan Месяц назад

what happens if you reset the cycle count?

@DaKabayanTek Месяц назад

It will reset it but when you look at 3Utools is will still show the original cycle count.

@MrDinakdakan Месяц назад

@@DaKabayanTek have ordered RELIFE XA2 Pro instead, looks similar to w09 but newer, i think lol

@DaKabayanTek Месяц назад

they work all the same...

@Spiritualquantic 16 дней назад

my brother, if i don't have the original flex, i can remove the message error using a other battery also? Or it will show the message? Please i need know this

@DaKabayanTek 14 дней назад

if you do not have the original flex the message will still show. The flex has the encrypted chip that hold the information of the original battery

@Spiritualquantic 14 дней назад

@@DaKabayanTek this is so bad

@meaddela1828 4 месяца назад

Hello, does it mean with this work around I wouldn’t need a tag on flex for all models ?

@DaKabayanTek 4 месяца назад

technically yes you dont need it but I still put a pre-programmed tag on flex after this method. 🍎 has been smart like what they did on ios17.4. Also you might want to watch the Q&A ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-K5gb8r2ZTcU.html

@meaddela1828 4 месяца назад

@@DaKabayanTek alright alright, thanks 🫡

@meaddela1828 4 месяца назад

@@DaKabayanTek I’m sorry one more question 😅. So after programming the original battery with WS09 Pro, I’d have to take off the BMS and weld it on the new battery cell ?

@DaKabayanTek 3 месяца назад

yes you have to weld it to the new battery cell...

@covengarden День назад

New battery will have 0 cycles of charge?

@DaKabayanTek 13 часов назад

battery health and cycles are on the bms. this process is just going around a loop hole on the ios. similar to adding a tag on. So regardless you change it on the programming device it will still read the original battery health and cycle on 3UTools unless you add a tag on flex. A follow up video I posted to answer these similar questions...

@cesarmtz247 4 месяца назад

Hi, this tool is still working with iOS 17.4?

@DaKabayanTek 4 месяца назад

I will post a follow up video when i get back from vacation..

@DaKabayanTek 4 месяца назад

video that might interest you... ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-K5gb8r2ZTcU.html

@Shamicahpadasas 23 дня назад

@@DaKabayanTekkabayan ano gamit mow sah pang hinang battery terminal po?

@LightningFastRepair 5 месяцев назад

What I want to know about this is its software. Do this on a phone and then erase the phone see if it still shows 100% and no battery message

@DaKabayanTek 5 месяцев назад

Sorry for the late reply, Even if you erase the device and restore to factory it will still keep the 100% and no battery message as per my experience. I will post a follow up video for this procedure and will try to answer my questions and questions from the FB group... Will probably upload it the coming week.

@DaKabayanTek 4 месяца назад

Answering your question ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-K5gb8r2ZTcU.html