Our system was put in in 2004. They have made a few changes since then. The safety clips the clear sediment filter case. The leak preventer system. Cutting the drain line at a 45 will keep the line from being restricted if it was push in to far. We have the 5 filter system. What pressure should the tank be empty, and when it is full?
Pretty much everything. From their website: "The heart of the system is the reverse osmosis (RO) filter, which removes contaminants down to 0.0001 microns: Virtually nothing can squeeze through the filter except for water molecules." Then there is a remineralizer to put some minerals back in to return the pH level back to normal.
Clear, concise, & to the point. Excellent demonstration. Walked me through the whole process. Other videos must be using older models because they did not match up with the system I have but yours was spot on. Thank you!
Hi any body can help me i change all the filter but still the water no good I check the water still not good the give me 46 % the water no good I don't know what to do i have the machine to check the water
I am not sure what the 46% reading is you are getting. If you are still getting bad water, something isn't hooked up properly. Hard to tell what it is from here, but go back over it and make sure everything it hooked up with the proper flow direction.
Near the end I went over how the leak stop valve works, and how to install it. It just gets secured to the floor near the RO system, and you cut the red supply line and connect the supply side to the red connector and the part of the red hose that goes to the filter to the Grey connector on the leak stop valve. I didn't show it because I didn't install it. It seemed kind of low tech to me.
Dude you’re the best. Got it done in an hour. Had to replace my old cold water line and shut off valve in the process but this guide was amazing. Definitely subscribed thanks again 🔥
Hi there - just dropping by to say thank you. This is one of the BEST install videos I could find on RU-vid for this series of RO system. Do you have a video on when/how to change different stages of filters, and test water quality etc? Thanks again, and keep up the great work!
Awesome, thank you! I haven't done a filter chang, yet, but will post a video as soon as I do. We have a local water testing lab, so I just pick up bottles from them, give them samples and they send me the results.
Great video thanks. I’m having an issue with a vibration in the red supply line right at the stop leak detector after replacing my filters (didn’t do it before) Any suggestions? Thanks.
Thank you so much for the detailed video.. how long does the water continue to drain when a new filter is installed.. mine is draining since a couple of hours.. is that normal?
What if my drain pipe was made of copper? Can I drill a hole in copper the same way? I have a titanium coated 1/4 inch bit that I’m gonna use. Install the saddle the same way but is it a good idea?
It shouldn't matter as long as it is the same diameter pipe so that the saddle fits. I don't remember the size of the drill bit , but make sure that is the correct size so that the hose going in there is a snug fit. Otherwise, it may leak a little.
At 11:56, is that a sticker on the RO membrane? Doesn't get removed? Also the hole for the faucet opening is 1/2" correct? Thanks for the detailed installation video btw.
That area on the filter shouldn't get water around it. They encourage you to not touch the membrane cartridge, so I would just leave it alone. If you have to drill a hole, it should be 1/2". I used the hole for the sprayer, which is quite a bit bigger than that, and it is working just fine. Thanks!
It is normal for water to come out of the drain hose, but it isn't usually more than a trickle. It may trickle for a few days. If a large volume of water is coming out of the drain hose, it sounds like something isn't right.
Question: Under normal operating conditions, how much water is actually sent to the drain in this system? Let's say you plug the system in, open the inlet valve, let the system fill and don't use any water (like in a "away from home" scenario), how much water will actually be sent to the drain ? I’m considering an installation in which I collect the waste water for cleaning / plant watering but wonder how much water this would actually mean. Thanks
This is a really good question, and I have no idea. It would be an interesting experiment. I like your idea of using the waste water, rather than it just going down the drain.
I didn't. Toward the end of the video I describe how to install it. It needs to be on the floor of the cabinet (or wherever you have the system installed) so that if it starts leaking, the valve will get wet, causing the puck to expand and shut off the valve.
Great installation video. I like the end part where you show how to flush the system and letting the carbon out until the water runs clear. when its time to replace the filters I will follow your way . I found the water that came out of the RO system tasted awful. RO takes out all the minerals and we are used to drinking water that has minerals, especially if you drink spring water. I found this company Vitev and they have the Remin Ph or Remin CA filters which you put at the end of the system and it adds all the minerals you need to have great tasting water. I use the CA because I don't want to put the my water to high in PH. It also replaces the filter that comes after the membrane and that also gives you more pressure at the tap. Check it out. totally worth it.
I installed it 6 months ago and haven't had any issues with it. I just did the 6 month filter change and will be posting that video on Wednesday. The only other RO system I am familiar with is AOSmith which I also made vidoes about. I chose the iSpring because the filters are less expensive. I haven't had any problems with AOSmith, but other people have posted that they have had leaks from the filter sumps.
Excellent job. On mine, the "pressure" of holding tank was slightly low, used bicycle tire pump to increase pressure to recommended guideline. Wished I had seen your video prior to installing mine... I HATE directions. Thank you sir!!
Hello, if I didn’t flush the 3 stages does it ruin the filters? I just connected it and ran the flush through the system. I forgot the part at video 18:20
I don't think you ruined anything. Probably some of the carbon dust from the filters went to the RO membrane. Probably a tiny reduction in efficiency for the membrane.
Good video, just be careful about too many wraps of Teflon tape, fitting could pop off under pressure if not enough thread bite. I also flushed the other carbon filter as well. Surprised at how much carbon comes out. Could plug other filters or membrane.
This was a big help and very well done. I had a little leak at first and fixed it easily by reinstalling the tubing. But I forgot that the shut off valve was activated by the leak 2 hours later as I checked to see if the tank was full. I made a by pass line without hooking up the stop leak and water flowed normally. Thanks for your helpful video, looking forward to the replacement video.
Thanks! I really appreciate your comment. I am glad you found the video helpful. I have uploaded the 6 month filter change video. It went live a week or two ago, I think. Enjoy!
@@TheFixitShed Thank you for uploading the filter change video. Looking forward to viewing it and saving it for the next time we have to do a filter change. I wrote the date down we installed under the sink on the sticker provided by the system. Your video's sure made it much easier to view and put this together for us. Nina and Philip, Fla. Thank You.
Thank you so much for the detailed video.. how long does the water continue to drain when a new filter is installed.. mine is draining since a couple of hours.. is that normal?
Probably not, but not a bad idea to check.when you check the air pressure, the tank has to be empty. When it is empty, the air pressure should be 5-7 psi.
Great video. Used it for my RCC7. I had no problems with the installation. My water valve didn’t have a gasket. Always handy to have a multi gasket kit for such an occasion. thanks for making the video.
Best video on installing these systems. To be honest, all of these systems are basically the same thing, but the instructions that come with them are not created equal. Without this video I think I would have convinced myself I hadn't hooked something up right or didn't have enough pressure because my instructions said nothing about waiting times between various stages at the end of the process. Super helpful. Thanks.
Thank you so much uploading this video, i was really confuse to assemble when i cleaning all parts of filter , after assembal was wrong when i c this video
If you opened all of the valves you closed to change the filters, the only other thing I can think of is the stage 2 filter. It is directional, and if you installed it upside down, that could be an issue. I have a video on replacing the filters here: ru-vid.com/video/%D0%B2%D0%B8%D0%B4%D0%B5%D0%BE-5NErj8eATxE.htmlsi=8-y6RrsetTDM68te
Hard to say without more info. I highly recommend contacting iSpring for tech support. If you go to their website (123filter.com), the contact info is there (phone, text, fax...). Or open a ticket at the top of the page.
Great Video - bought the ispring specifically because of how good this install video was. Thank you for your help, clear instructions and good video placement. Cheers
Thank you for this video. Question though... Does the cold water have to be turned off to drain the tank or can I leave that on and it will eventually start trickling more slowly? (30 min in water still strong)
If you are 30 minutes on and it is still going strong, that doesn't seem right to me. The tank only holds 1 gallon. Once that is empty, it should flow at the rate the RO membrane will allow, which is just a trickle.
Im having problems withe the osmosis filter, the water wont come out from the filter, I removed it to check if the pressure was good and it is, I pushed the osmosis filter to the end of the tube but it's not coming out, do you have any idea? Thanks for the vid
@TheFixitShed yes it does, and actually I added more pressure into the tank till 40 psi but nothing, actually I asked for a replacement and they send it but it's happening the same
@@greylp88 If you disconnect the water inlet from the RO filter, as I shoed in the video to flush the carbon out from the new filters, does water come out?
Great video man. By chance would you know if a hose could be T'ed off into a refrigerator? Would love to have filtered water coming out of my fridge as well.
Great video! Just installed a system identical. Wish I had watched this first. Has anyone had any failures with these push quick connects? Just curious because I am not familiar with them.
I am sure they have. If you have any issues, you just want to make sure the cuts on the ends of the hoses are as clean and square as possible. A jagged or angled cut can cause a leak in the connectors.
Great video. It made installing my system a breeze. You really need to tighten those vertical filters. Luckily the leak detection uses standard compressed tissue disks and it works very well.
Hi, I just installed a system like this, 7 stage, and notices that the water flow was clearly reduced when getting water from the fridge. Before it was a direct line and it had pretty good pressure, after the filtration system the flow was drastically reduced. Is this normal or did I do something wrong? Great video, btw
Hi I just bought the same system and i expect to receive it in a couple days. Did you receive results from lab test? How is the taste of water before and after installation? Here in europe this filter cost around 400€, so i hope i did a good purchase 😄
My water tasted fine before and after installation. My problem was lead in the water. We did have it tested before and after installation, and don't actuallt remeber the numbers, but before it was high and after the installation it was at an acceptable level. Sorry for being vague.
Most likely it is just air bubbles. If you let the water sit for a minute, it should clear up. It seems to happen when water pressure is higher. I have low water pressure so it comes out clear. Slowly, but clear. My friends have higher water pressure (like a fire hose) and theirs comes out cloudy, but a minute later it is clear.
Hi! Thanks a lot for the video, very well explained, installation was super easy :) If I go on vacation for a month and I shut off the water supply, do I need do to anything specific when I come back, like draining the tank or that is not necessary ?
Glad it helped! Do you have to? Not really. Running for a few minutes until it reduces to a trickle would drain the tank, and resupply it with fresh water. It wouldn't hurt.
Sure doesn't look like it on the video, I'll check next time I am down there. It probably isn't critical. That is not a pressurized line, so you don't really have to worry about leaks coming from it. If you have a clip to put in there, I would put one in there, though.
Thank you so much for this video! I bought this system but don't even have the tools yet, hence why I'm watching your video! In your case, your RO faucet could be fitted into the existing hole in your sink set. If I don't have a hole, can I just drill it with any regular drill for drilling into PVC pipes (that I will go buy)? Also, at 6:50, you drilled into the vertical part of the drain pipe. I had seen other vids that said to drill the hole on the horizontal part to prevent dripping sounds; was there a reason you chose the vertical part? And would the horizontal part of your drain pipe been sufficiently long to drill a hole there if you wanted?
Any drill is fine for drilling a hole. But make sure you are using a drill bit for metal. (If you use a bit for wood, it will dull very quickly.) The reason I drilled into the vertical part is because that is what the directions said to do. You could probably drill into the top of the horizontal part, but the base of the sink might make that difficult.
Is it specks in the water ot air bubbles? I have a friend who gets a lot of air bublles. If you let it sit for a minute, it clears up. If it is white particles, that should not be.
I didn't realize it went further into the housing for the RO MEMBRANE container and had to touch it momentarily. Will that cause a bacterial build up or something?
The storage tank pressure should be arounf 5-7 lbs (You may want to check with iSpring to double check that range, but it is close). You have to check the pressure when there is no water in the tank. Over inflating will damage it. Adding more pressure to the tank does not increase the pressure coming out of the faucet.
By the way, had another Q - I had a leak at the yellow quick-connect on top of the pressurized water tank. Tried reconnecting, inserting it all the way in etc, but did not stop the leak. Finally, I cut the yellow hose about an inch down, put a lil vaseline on hose, stuck it back all the way into the quick-connect, and now the leak the gone. However, in that process, I ended up opening the tank's cap, and all the pressurized water literally splashed up the ceiling! Does this mean I need to check/re-pressurize the tank (up to ~10psi?), or is that normal, and let it be? The pressure at the outlet faucet seems okay - but not too fast.
It could be that the end of the yellow line had an imperfection, and making another cut was the right solution. If water came out of the tank, then when you reconnect everything, it should repressurize and be fine. If you let AIR out, then you would need to put air back in.
@@TheFixitShed Didn't let the air out, just the water came out (pressurized). Cool, will leave it alone then :) Drilling the hole in the granite was a ***** ! I hit the steel corner plate of the sink under the granite... and it took some work and lot of patience to get through. But, so happy it is all done and working great now :)
I am not sure that I understand the question. The RO filters the water and stores it in the pressure tank. The RO process is slow so you need the tank to save up the filtered water so that it comes out quickly when you want it. If you don't have the tank the water flow would be restricted by the filters and would just come out of the faucet as a trickle regardless of your water pressure in the rest of the house. I hope that answered it.
@@TheFixitShed Sorry I should have been more clear on my question, thanks for your response, I was asking do I need to purchase a system with a pump? but I purchased RCC7AK 6 after seeing your video and followed your instructions to install it on my own, It's working perfectly good without a motor pump. thanks a lot for your step-by-step instructions. You really did an excellent video here. I really appreciate it.
@@sabai005 Thank you! I am glad it helped. Sorry I messed up on the question, but glad you sorted it out. I actually didn't realize you could get the RO system with its own pump. I'll have to check that out.
If you want to fixt it, you could replace the piece of pipe. Its not terribly expensive. If you just want to plug it, off the top of my head, I would cut a small piece from a pvc pipe (maybe 1" by 1"), use plumbers putty between the patch and the pipe with the hole and put a hose clamp around it.
If you have the RCC7AK 6 stage system, I don't see where you can buy just a single set of filters. you can buy this one year set amzn.to/3cnpnLl, but it doesn't come with the RO membrane. You can buy that separately here amzn.to/3Kn9u4i
RO filtration is a slow process, so the tank holds filtered water so that there is some available when you need it, and you don't have to wait 5 minutes for it to fill a glass of water.
@@WebGuyTV The replacement filters are a little pricey. Other than that, it has been ok. I have seen a bunch of review online with complaints of leaking, but I haven't had any. I installed on at my son's place and opted to go with iSpring. It had good reviews, and the replacement filters are a little less expensive. I have done a couple of videos on that system as well. If you haven't bought a system yet, I would check them out as well.
Best installation video!!! Thank you so much for the amazing explanations and great video angles. If you're looking for a video for this filter, look no more...save your time and watch this one!! Thank you man! 🙌
Could you please help me the leak protection... I understand one side goes to the red but what connects to the Grey? Also our water is cloudy, any suggestions? I filled and emptied tank 3x
@@loupakisathleticcenter9667 The red line is the supply line that delivers water from the FEED WATER ADAPTER to the RO system. You will cut this line in the middle somewhere and insert the leak stop valve. So the red line will go from the FEED WATER ADAPTER to the LEAK STOP VALVE, and then the red line will come out of the other side of the LEAK STOP VALVE and go to the RO system. The cloudy water is probably just air bubbles. If you let the water sit in a glass for a minute it should clear up. If it doesn't, I would contact iSpring and ask them.
